Table of Contents
Advertisement
of the top wings. When the model is balanced correctly the
wings and horizontal stabilizer will be level (the model in the
photo is very slightly tail-heavy). If the tail is low the model
is "tail heavy" and weight must be added to the nose. If the
nose is low the model is "nose heavy" and weight must be
added to the tail. Carefully lay segments of Great Planes
"stick-on" lead (GPMQ4485) on the tail or nose until you can
get the model to sit level. Once you know how much weight
is required, attach it to the model. Tail weight can be stuck to
the fuselage under the horizontal stabilizer and nose weight
can be stuck to the fi rewall next to the motor–it is likely that
1/2 to 1 oz. [15 to 30 grams] will be needed on the fi rewall to
get the model to balance.
❏
3. IMPORTANT: If you found it necessary to add any weight,
recheck the C.G. after the weight has been installed.
Balance the Model Laterally
❏
1. Lift the model by the tail skid and the propeller shaft
several times and note which wing tip drops.
❏
2. If one wing always drops, it means that side is heavy.
Balance the airplane by adding weight to the bottom of the
opposite wing near the tip. An airplane that has been laterally
balanced will track better in loops and other maneuvers.
PREFLIGHT
Identify Your Model
No matter if you fl y at an AMA sanctioned R/C club site or
if you fl y somewhere on your own, you should always have
your name, address, telephone number and AMA number
on or inside your model. It is required at all AMA R/C club
fl ying sites and AMA sanctioned fl ying events. Use a fi ne-
point felt-tip pen to write the information somewhere inside
the airplane such as on the bottom of the cockpit.
Charge the Batteries
Follow the battery charging instructions that came with your radio
control system to charge the transmitter batteries. You should
always charge your transmitter the night before you go fl ying,
and at other times as recommended by the radio manufacturer.
CAUTION: Unless the instructions that came with your
radio system state differently, the initial charge on new
transmitter and receiver batteries should be done for 15
hours using the slow-charger that came with the radio
system. This will "condition" the batteries so that the next
charge may be done using the fast-charger of your choice.
If the initial charge is done with a fast-charger the batteries
may not reach their full capacity and you may be fl ying with
batteries that are only partially charged.
Range Check
When you get to your fl ying site ground check the
operational range of the radio before the fi rst fl ight of the
day. With the transmitter antenna collapsed and the receiver
and transmitter on, you should be able to walk at least
100 feet away from the model and still have control. Have
an assistant stand by your model and, while you work the
controls, tell you what the control surfaces are doing. Repeat
this test with the motor running at various speeds with an
assistant holding the model, using hand signals to show you
what is happening. If the control surfaces do not respond
correctly, do not fl y! Find and correct the problem fi rst. Look
for loose servo or battery connections, damaged wires or a
damaged receiver crystal from a previous crash in another
model. One other possible source of radio "noise" that could
cause interference is the arrangement and relative location
of the receiver, receiver antenna and motor wires. If possible,
remount the receiver in a different location or re-route some
of the wires. Then, try the range check again.
ELECTRIC MOTOR SAFETY PRECAUTIONS
Failure to follow these safety precautions may result
in severe injury to yourself and others.
Use safety glasses when running the motor.
Do not run the motor in an area of loose gravel or sand; the
propeller may throw such material in your face or eyes.
Keep your face and body as well as all spectators away from
the plane of rotation of the propeller as it is turning.
Keep these items away from the prop: loose clothing, shirt
sleeves, ties, scarfs, long hair or loose objects such as
pencils or screwdrivers that may fall out of shirt or jacket
pockets into the prop.
Always remove the LiPo battery from the plane before charging.
Always use a charger designed to charge LiPo batteries for
charging the LiPo fl ight battery.
Never leave the LiPo battery unattended while charging. If
the battery becomes hot, discontinue charging.
20
Advertisement
Table of Contents
