Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for daltile 828 BrS
Summary of Contents for daltile 828 BrS
- Page 1 TILE SAW 828 BrS OPERATING MANUAL...
- Page 2 Keep this Manual in a safe place for future reference. ® Enter the Serial Number of your new Daltile 828 BrS Tile Saw in the box below. The Serial Number is located on the motor cover. PAGE 2 DALTILE 828 BrS OPERATING MANUAL V02/2004R1...
-
Page 3: Table Of Contents
Connecting to Power Supply ........................12 Motor Protection ............................12 Installing the Saw Blade ..........................13 3. OPERATING INSTRUCTIONS Cutting Procedure ............................14 45˚ Miter Cutting ............................14 4. MAINTENANCE AND TROUBLESHOOTING General Maintenance ..........................15 5. SPARE PARTS Spare Parts ..............................16 DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 3... -
Page 4: Daltool Safety
If the instructions are not that all tools are removed or in their proper followed it is possible that serious injuries could storage area before the machine is turned on. occur as well as death. PAGE 4 DALTILE 828 BrS OPERATING MANUAL V02/2004R1... - Page 5 Do not force the equipment to ment. If proper footing is not observed by do something that it wasn’t designed to do. doing such things as overreaching, serious injury may occur. DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 5...
- Page 6 Any part of the machinery that is damaged should be checked carefully to determine whether or not it should be used and whether or not it can function properly for its intended use. PAGE 6 DALTILE 828 BrS OPERATING MANUAL V02/2004R1...
-
Page 7: Hazard Symbols
OFF position death or damage to the before plugging the machine into equipment. an electrical outlet to prevent accidental starting of the machine. DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 7... -
Page 8: California Proposition 65 Message
Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. PAGE 8 DALTILE 828 BrS OPERATING MANUAL V02/2004R1... -
Page 9: Electrical Requirements And Grounding Instructions
3-prong grounding plugs and 3-pole nector, if an extension cord is used. receptacles that accept the tool’s plug. Repair or replace a damaged or worn Continued on page 10 cord immediately. DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 9... -
Page 10: Tile Saw Specific Warnings
It is important not to use an extension cord that is undersized. Using an undersized extension cord can result in low voltage to the motor thus resulting in a motor burnout or premature failu- PAGE 10 DALTILE 828 BrS OPERATING MANUAL V02/2004R1... -
Page 11: Machine Specifications
Height (without legs)........15 3/4” sockets at the underside of the water container Weight ............90 lbs and fastened with the knobs. Noise level ..........80 dB (A) Noise level during sawing ....90 dB (A) DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 11... -
Page 12: Unpacking And Setting Up
UNPACKING AND SETTING UP Unpacking and Assembly Cooling System Unpack the tile saw and inspect for any damaged parts. Install the legs in the sockets at the under Operating the water pump without a sufficient side of the water container and fasten with supply of water may result in pump damage. -
Page 13: Installing The Saw Blade
(Check the direction of rotation and make sure the blade is well centered) Mount saw flange and tighten with the hexagon nut. Place the blade guard and tighten with the 2 knobs. DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 13... -
Page 14: Operating Instructions
Perform the cut. Turn the motor OFF when work is Place the material to be cut on the sawing complete. table and position against the fixed stop and eventually the adjustable stop. PAGE 14 DALTILE 828 BrS OPERATING MANUAL V02/2004R1... -
Page 15: General Maintenance
Cleaning the pump as described above and leaving it outside the water container is recommended. Regularly check the saw flanges for wea- ring out and replace if necessary. DALTILE 828 BrS OPERATING MANUAL V02/2004R1 PAGE 15... -
Page 16: Spare Parts
ITEM NR. DESCRIPTION 6.516.018 MOTOR 6.513.335 SWITCH 6.516.026 MOTOR FLANGE 6.516.021 SAW FLANGE 6.516.023 FLANGE NUT 6.513.289 CAPACITOR 6.513.298 PUMP 6.005.792 KNOB 6.509.065 ADJUSTABLE HANDLE 4.207.040 GUIDING ROLLER 4.207.026 GUIDING BEAM 6.509.070 HANDLE PAGE 16 DALTILE 828 BrS OPERATING MANUAL V02/2004R1...