Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for daltile 1020 TS
Summary of Contents for daltile 1020 TS
- Page 1 TILE SAW 1020 TS OPERATING MANUAL...
- Page 2 ® 1020TS. Keep this Manual in a safe place for future reference. Enter the Serial Number of your new Daltile ® 1020TS Tile Saw in the box below. The Serial Number is located on the motor cover. PAGE 2 DALTILE 1020TS OPERATING MANUAL V02/2004R1...
-
Page 3: Table Of Contents
Cutting Straight Edges ..........................14 One-Step Sawing ............................14 Multiple-Step Sawing ..........................14 45˚ Miter Cutting ............................14 4. MAINTENANCE AND TROUBLESHOOTING General Maintenance ..........................15 V-Belt Inspection, Adjustment and Replacement ..................15 5. SPARE PARTS Spare Parts ..............................16 DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 3... -
Page 4: Daltool Safety
If the instructions are not that all tools are removed or in their proper followed it is possible that serious injuries could storage area before the machine is turned on. occur as well as death. PAGE 4 DALTILE 1020TS OPERATING MANUAL V02/2004R1... - Page 5 Do not force the equipment to ment. If proper footing is not observed by do something that it wasn’t designed to do. doing such things as overreaching, serious injury may occur. DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 5...
- Page 6 Any part of the machinery that is damaged should be checked carefully to determine whether or not it should be used and whether or not it can function properly for its intended use. PAGE 6 DALTILE 1020TS OPERATING MANUAL V02/2004R1...
-
Page 7: Hazard Symbols
OFF position death or damage to the before plugging the machine into equipment. an electrical outlet to prevent accidental starting of the machine. DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 7... -
Page 8: California Proposition 65 Message
Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. PAGE 8 DALTILE 1020TS OPERATING MANUAL V02/2004R1... -
Page 9: Electrical Requirements And Grounding Instructions
3-prong grounding plugs and 3-pole nector, if an extension cord is used. receptacles that accept the tool’s plug. Repair or replace a damaged or worn Continued on page 10 cord immediately. DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 9... -
Page 10: Tile Saw Specific Warnings
It is important not to use an extension cord that is undersized. Using an undersized extension cord can result in low voltage to the motor thus resulting in a motor burnout or premature failu- PAGE 10 DALTILE 1020TS OPERATING MANUAL V02/2004R1... -
Page 11: Machine Specifications
Cutting table dim.....18 5/8” x 15 3/4” and fastened with the knob. Length...............42” Width............23 5/8” Height (without legs) ........ 24 1/2” Weight ............176 lbs Noise level..........89 dB (A) Noise level during sawing ....98 dB (A) DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 11... -
Page 12: Unpacking And Setting Up
Movable Cutting there is a grounded power supply, Table the extension cord’s meets criterea as Ensure the Adjusting Knob is tight mentioned in the table on page 10. PAGE 12 DALTILE 1020TS OPERATING MANUAL V02/2004R1... -
Page 13: Motor Protection
Mount saw flange and tighten with the hexagon nut. Place blade guard and secu- re it using the 2 knobs. Adjustable cutting depth stop. DALTILE 1020TS OPERATING MANUAL V02/2004R1 PAGE 13... -
Page 14: Operating Instructions
Multiple Step Cutting With this sawing process the sawing blade must be adjusted to a desired cutting depth. The material can be cut to the adjusted depth by PAGE 14 DALTILE 1020TS OPERATING MANUAL V02/2004R1... -
Page 15: General Maintenance
V-Belt Inspection, Adjustment and Replacement: The DalTile 1020TS is designed with a power transmission V-belt. In order to ensure the O. Repeat steps M and N until proper V-belt DalTile 1020TS operates at peak efficiency, the tension is achieved. -
Page 16: Spare Parts
ITEM NR. DESCRIPTION 6.516.045 MOTOR 6.516.040 V-BELT 6.513.335 SWITCH 4.405.010 FIXED FLANGE 4.405.140 SAW FLANGE 6.503.170 FLANGE NUT 6.513.320 CAPACITOR 6.513.298 PUMP 6.005.792 KNOB 6.509.080 ADJUSTABLE HANDLE 4.356.080 GUIDING ROLLER 4.356.055 ROLLER 6.509.085 HANDLE PAGE 16 DALTILE 1020TS OPERATING MANUAL V02/2004R1...
Need help?
Do you have a question about the 1020 TS and is the answer not in the manual?
Questions and answers