Matrix Fitness G7-S52 Back Extension Owner's Manual
  1. Manuals
  2. Brands
  3. Matrix Fitness Manuals
  4. Fitness Equipment
  5. G7-S52 Back Extension
  6. Owner's manual

Matrix Fitness G7-S52 Back Extension Owner's Manual

Ultra single-station strength
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNERS MANUAL
ULTRA Single-Station Strength
G7-S52 Back Extension

Advertisement

Table of Contents
loading

Related Manuals for Matrix Fitness G7-S52 Back Extension

Summary of Contents for Matrix Fitness G7-S52 Back Extension

  • Page 1 OWNERS MANUAL ULTRA Single-Station Strength G7-S52 Back Extension...

  • Page 2: Table Of Contents

    Table Of Contents Safety, General Care & Maintenence ........................3 Getting Started (Product Specifications) ......................5 Assembly Information .............................6 Markings ..................................7 Parts List ...................................8 Installation & Assembly: Value Line Part 1 Weight Stack & Mid Frame Assembly ...................9 Part 2 Arm Assembly ..........................11 Part 3 User Frame Assembly ........................

  • Page 3: Safety, General Care & Maintenence

    IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INFORMATION It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use. PROPER USAGE Do not use any equipment in any way other than designed or intended by the manufacturer.
  • Page 4 IMPORTANT SAFETY INSTRUCTIONS WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID INJURY! Never allow children on strength training equipment. Teenagers must be supervised at all times while using this equipment.

  • Page 5: Getting Started (Product Specifications)

    GETTING STARTED EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST EXERCISE PLACARD PRODUCT SPECIFICATIONS TECH SPECS Maximum User Weight 136 kg / 300 lbs. Maximum Training Weight 109 kg / 240 lbs. Product Weight 283 kg / 623 lbs. Overall Dimensions (L x W x H) 145.2 x 119.7 x 129.6 cm / 57.2"...

  • Page 6: Assembly Information

    ASSEMBLY UNPACKING | TOOLS REQUIRED UNPACKING Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Matrix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the machine.

  • Page 7: Markings

    MARKINGS WARNING LABEL LOCATIONS Hazard warning sticker (faces rearward)

  • Page 8: Parts List

    Parts List DESCRIPTION M10 X 75L Socket Head Cap Screw Pulley Bracket M10 Flat Washer M10 Nylock Nut Weight Stack M10 X 30L Socket Head Cap Screw Lower Connecting Tube Pulley Guard Inner Frame M10 Saddle Washer Wave (Spring) Washer Washer (45 OD X 30.3 ID) Axle/ROM Assembly M10 X 25L Socket Head Cap Screw...

  • Page 9: Part 1 Weight Stack & Mid Frame Assembly

    ASSEMBLY PART 1: MID FRAME ASSEMBLY STEP 1 | WEIGHT STACK INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 X 75L SHC Pulley Bracket M10 Flat Washer M10 Nylock Nut Weight Stack M10 X 30L SHC Lower Connecting Tube Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN .
  • Page 10 ASSEMBLY PART 1: MID FRAME ASSEMBLY STEP 2 | MID FRAME INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 X 75L SHC M10 Flat Washer M10 Nylock Nut M10 X 30L SHC Pulley Guard Inner Frame M10 Saddle Washer View A • Ensure that the frame is level and that all floor pads contact the floor equally • Install the frame hardware as shown, orienting the saddle washers as shown in View A.

  • Page 11: Part 2 Arm Assembly

    ASSEMBLY PART 2: ARM ASSEMBLY STEP 1 | CAM & CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY Wave (Spring) Washer Washer (45 mm OD X 30.3 mm ID) Axle/ROM Assembly • Remove CAM plate as shown - NOTE: two hex wrenches are required. Set hardware aside to be used later • Assemble Axle/ROM assembly and CAM; orient CAM as shown • Assemble cable onto CAM groove...
  • Page 12 ASSEMBLY PART 2: ARM ASSEMBLY STEP 2 | CAM & CABLE ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 Flat Washer M10 X 25L SHC Key (10 X 8) • Capture cable end with retaining clip • Assemble Key into Axle/ROM as shown • Using two hex wrenches, reassemble CAM plate and torque fasteners to: 39 N-m/29 ft-lbs.
  • Page 13 ASSEMBLY PART 2: ARM ASSEMBLY STEP 3 | ARM ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 x 25L BHC Exercise Arm M10 Flat Washer (42 mm Diameter) Medium Pivot Cap Torque to 77 N-m/57 ft-lbs.
  • Page 14 ASSEMBLY PART 2: ARM ASSEMBLY STEP 4 | COUNTER WEIGHT ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M8 X 20L SHC M8 Flat Washer Counter Weight Torque to 39 N-m/29 ft-lbs.

  • Page 15: Part 3 User Frame Assembly

    ASSEMBLY PART 3: USER FRAME ASSEMBLY STEP 1 | MID CONNECTION ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 X 30L SHC M10 Saddle Washer Mid Connecting Tube View A • Install the user frame hardware as shown, being sure to orient the saddle washers as shown in View A.
  • Page 16 ASSEMBLY PART 3: USER FRAME ASSEMBLY STEP 2 | USER FRAME ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 Nylock Nut M10 X 30L SHC M10 Saddle Washer User Frame M10 X 140L SHC View A 24 10 • Ensure that the frame is level and that all floor pads contact the floor equally • Install the frame hardware as shown, orienting the saddle washers as shown in View A.

  • Page 17: Part 4 Pad Assembly

    ASSEMBLY PART 4: PAD ASSEMBLY STEP 1 | BACK PAD ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 Flat Washer M10 X 20L BHC Lumbar Back Pad Orient the pad as shown. Tighten to 27 N-m/20 ft-lbs.
  • Page 18 ASSEMBLY PART 4: PAD ASSEMBLY STEP 2 | BOTTOM PAD ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M10 Flat Washer M10 X 20L BHC Install the pad as shown. Tighten to 27 N-m/20 ft-lbs.

  • Page 19: Part 5 Plastics Assembly

    ASSEMBLY PART 5: PLASTICS ASSEMBLY STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY Left Front Shroud Rear Shroud Right Front Shroud Install the weight stack shrouds as shown.
  • Page 20 ASSEMBLY PART 5: PLASTICS ASSEMBLY STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES DESCRIPTION QUANITY M8 X 60L SHC Top Cap Install the top cap and connect rep counter plug as shown. Torque to 17 N-m/147 in-lbs. I M PO RTA NT NOTI CE Position top cap so Rep Counter faces the user.
  • Page 21 Matrix Fitness 1600 Landmark Drive Cottage Grove WI 53527 matrixfitness.com Toll-free 866.693.4863 Facsimilie 608.839.8687 ULTRA Back Extension Owners Guide rev.1.2 Copyright© 2014 Matrix Fitness...

Table of Contents