Download  Print this page

Panasonic KX-TGP600 Operating Instructions Manual

Sip cordless phone.
Hide thumbs
Most useful pages: More

Advertisement

Table of Contents
KX-TGP600
Thank you for purchasing this Panasonic product.
Please read this manual carefully before using this product and save this manual for future
use.
Please use only the batteries provided and charge the batteries for about 6 hours before using
the handset for the first time. For details, see "Charging the Batteries", Page 82 in this
manual.
Note
R In this manual, the suffix of each model number is omitted unless necessary.
R The illustrations such as some keys may differ from the appearance of the actual product.
R Certain products and features described in this document may not be available in your
country or area. Contact your phone system dealer/service provider.
R The contents and design of the software are subject to change without notice.
Document Version: 2015-02

Operating Instructions

Model No.
Model No.
SIP Wireless Desk Phone
Model No.
KX-TPA60
SIP Cordless Phone
KX-TGP600
SIP Cordless Handset
KX-TPA60
KX-TPA65
KX-TPA65

Advertisement

Table of Contents

   Summary of Contents for Panasonic KX-TGP600

  • Page 1: Operating Instructions

    KX-TGP600 KX-TPA60 KX-TPA65 Thank you for purchasing this Panasonic product. Please read this manual carefully before using this product and save this manual for future use. Please use only the batteries provided and charge the batteries for about 6 hours before using the handset for the first time.
  • Page 2 Introduction Outline This manual describes information about the installation and operation of KX-TGP600, KX-TPA60 and KX-TPA65. Related Documentation R Quick Start Guide Describes basic information about the installation and safety precautions to prevent personal injury and/or damage to property. R Administrator Guide Describes detailed information about the configuration and management of this unit.
  • Page 3: Table Of Contents

    Table of Contents Important Information Using the Base Unit Phonebook (when connected to a base unit other than the KX-TGP600 Important Information ..........4 only) ..............69 For Users in European Countries .......5 Using the Remote Phonebook (when connected to For Users in the United Kingdom ......5 the KX-TGP600 only) ........71...
  • Page 4: Important Information

    Important Information Important Information Data Security R This telephone communicates using digital signals that are difficult to intercept. However, it is possible that the signals could be intercepted by a third party. R To avoid unauthorized access to this product: –...
  • Page 5: For Users In European Countries

    This device is a DECT Portable station operating in the frequency band of 1880 MHz to 1900 MHz. The usage of this device is generally allowed in all EU countries. Panasonic System Networks Co., Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC.
  • Page 6: For Users In Australia And The United Kingdom

    Important Information For Users in Australia and the United Kingdom R This unit is capable of being used in conjunction with hearing aids fitted with inductive coil pick-ups. The handset should be held as for normal conversation. For operation, the hearing aid should be set to its "T" position or as directed in the operating instructions for the hearing aid.
  • Page 7 Important Information R The handset may be carried and operated with only the specific provided belt-clip. Other non-tested belt-clips or similar body-worn accessories may not comply and must be avoided. FCC ID can be found inside the battery compartment or on the bottom of the units. Note R This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 8: For Users In Canada

    Important Information For Product Service R Call 1-800-211-PANA (7262) for the location of your nearest authorized service center. R Panasonic’s e-mail address for customer inquiries: consumerproducts@panasonic.com For customers in the USA and Puerto Rico ONLY. For Users in Canada Industry Canada Notices and Other Information This product meets the applicable Industry Canada technical specifications.
  • Page 9 Important Information R To comply with IC RF exposure requirements, the base unit and KX-TPA65 must be installed and operated 20 cm (8 inches) or more between the product and all person’s body. R This product may not be collocated or operated in conjunction with any other antenna or transmitter. R The handset may be carried and operated with only the specific provided belt-clip.
  • Page 10: For Best Performance

    Important Information For Best Performance Operating Range R The range of operation depends on the topography of your office, weather, or usage conditions, because signals are transmitted between the base unit and the handset/desk phone by radio waves. R Normally, you get greater range outdoors than indoors. If there are obstacles such as walls, noise may interfere with your telephone calls.
  • Page 11: Battery Information (kx-tpa60 Only)

    Important Information Battery Information (KX-TPA60 only) After batteries are fully charged (at 25 °C [77 °F]): Operation Operating Time While Talking Up to about 11 h (Backlight off , Narrowband Mode) While Talking Up to about 8 h (Backlight on , Wideband Mode) While not in use (Standby) Up to about 200 h...
  • Page 12 Important Information Important Notice Concerning the Correct Use and Charging of Ni-MH Batteries Batteries, due to their construction, undergo some wear and tear. The lifetime of batteries also depends on correct maintenance. Charging and discharging are the most important factors. You should take notice of the following to maintain the life of the batteries as long as possible.
  • Page 13: Before Operating The Telephones

    <When the base unit is a KX-TGP600> The KX-TGP600 is a SIP Cordless Phone, which consists of a base unit, a cordless handset and a wireless desk phone, and has the following features. The handset is the same as the KX-TPA60 and the desk phone is the same as the KX-TPA65.
  • Page 14 2.0 standard and can be connected and used with any base unit that supports this standard. This manual describes how to connect to a base unit other than the KX-TGP600, but the availability of certain features, and the specifications of certain settings and operations will depend on the base unit being used.
  • Page 15: Accessory Information

    Before Operating the Telephones Accessory Information Included Accessories KX-TGP600 AC adaptor for Base unit: 1 Model No. Part No. KX-TGP600/KX-TGP600C/ PQLV219 KX-TGP600LA KX-TGP600AL PQLV219AL KX-TGP600CE/KX-TGP600RU PQLV219CE KX-TGP600LC PQLV219BX KX-TGP600UK PQLV219E DC Output: 6.5 V AC adaptor for Charger: 1 Model No.
  • Page 16 Before Operating the Telephones KX-TPA60 AC adaptor for Charger: 1 Model No. Part No. KX-TPA60/KX-TPA60C/ PNLV226 KX-TPA60LA KX-TPA60AL PNLV226AL KX-TPA60CE/KX-TPA60RU PNLV226CE KX-TPA60LC PNLV226BX KX-TPA60UK PNLV226E DC Output: 5.5 V Charger: 1 Belt Clip: 1 Batteries *1 Rechargeable AAA Ni-MH 1.2 V, 630 mAh batteries KX-TPA65 AC adaptor for Desk phone: 1 Model No.
  • Page 17: Optional Accessories

    Before Operating the Telephones Optional Accessories KX-TPA65 Item Model No. Wall mount kit KX-TPA65/KX-TPA65C: KX-A440 KX-TPA65AL/KX-TPA65CE/KX-TPA65LA/KX-TPA65LC/ KX-TPA65RU/KX-TPA65UK: KX-A440X...
  • Page 18: Location Of Controls

    Before Operating the Telephones Location of Controls Base Unit (KX-TGP600) Status Indicator Status Meaning Color Light pattern Green R The base unit is connected to the Internet. The startup process is complete and you may now make and receive internet calls.
  • Page 19 Before Operating the Telephones Amber R The base unit’s IP address may conflict with the IP addresses of other devices on your local network. Contact your administrator for further information. Slow Flashing R The base unit is obtaining an IP address or is obtaining configurations.
  • Page 20 Before Operating the Telephones Handset (KX-TPA60) [Back View] (KX-TPA60 only) (KX-TPA60C only) (KX-TPA60RU only) (All other models) Ringer/Charge/Message Indicator Status Meaning Color Light pattern Charging Slow Flashing There is a new missed call or voice mail. Quick Flashing Receiving a call —...
  • Page 21 The headsets can be used with this unit. (Not all operations with the headsets can be guaranteed.) For up-to-date information about headsets that have been tested with this unit, refer to the following web sites: http://panasonic.net/pcc/support/sipphone (TALK/Speakerphone) Key Used to make or answer calls, or toggle between Receiver mode and Hands-free mode during a conversation.
  • Page 22 Before Operating the Telephones (POWER/CANCEL) Key Used to end calls, exit the phonebook or Function mode. Press and hold this key to turn the handset on or off. /[XFER/CLR] Key Used to transfer a call to another party, or to clear digits or characters. /[FUNC] Key Pressing this key followed by a keypad number (0–9) allows you to perform various common functions quickly.
  • Page 23 Before Operating the Telephones Desk Phone KX-TPA65...
  • Page 24 Before Operating the Telephones KX-TPA65AL, KX-TPA65LA, KX-TPA65LC, KX-TPA65UK, KX-TPA65X F G H I...
  • Page 25 Before Operating the Telephones KX-TPA65C F G H I...
  • Page 26 Before Operating the Telephones KX-TPA65CE...
  • Page 27 Before Operating the Telephones KX-TPA65RU Handset Hook Keeps the handset stable when the unit is mounted on a wall. For details, see “Hooking the Handset (KX-TPA65)”, Page 84. Ringer/Message Indicator If an incoming call arrives, the indicator blinks in accordance with the LED pattern setting. Status Meanings Color...
  • Page 28 Used to cancel the selected item. Headset Jack The headsets can be used with this unit. (Not all operations with the headsets can be guaranteed.) For up-to-date information about headsets that have been tested with this unit, refer to the following web site: http://panasonic.net/pcc/support/sipphone...
  • Page 29: The Display And Icons

    Signal Strength Indicator - Out of range Battery Indicator - Needs to be charged. Off-hook Status Incoming Call Log Outgoing Call Log Intercom Indicator Voice Message Phonebook Navigator Key Guidance *1 KX-TPA60 only. *2 Not displayed when connecting to a base unit other than the KX-TGP600.
  • Page 30 Registration number of handset/desk phone Call Forwarding Do Not Disturb *1 Not displayed when connecting to a base unit other than the KX-TGP600. Time Display Date, New Message or Missed Call Display Handset/Desk phone number and Name (when connecting to a KX-TGP600 only) Soft Keys For more information, see Page 31.
  • Page 31: Soft Keys

    Before Operating the Telephones Soft Keys Icons and information shown on the display will vary depending on the context. To select an item shown on the display, press the corresponding soft key. Soft Key A (Left key) Suffix Meaning (none)/C/ UK/AL/ LA/LC RU/CE...
  • Page 32 Before Operating the Telephones Soft Key B (Middle key) Suffix Meaning (none)/C/ UK/AL/ LA/LC RU/CE Confirms the entry. Opens the main menu. When in standby mode, pressing this key for more MENU than 2 seconds locks all keys. Opens the list menu (edit/delete in the phonebook, etc.). MENU Stores a new item in the phonebook.
  • Page 33 *3*4 PAGE Used to set a Memo Alarm. *1 Not displayed when connecting to a base unit other than the KX-TGP600. *2 KX-TPA60 only. *3 This soft key is displayed only when configured on the telephone. *4 This soft key can be configured to appear as Soft Key A, B, or C.
  • Page 34 Before Operating the Telephones 4. [D]/[C]: "Soft Key Edit" a 5. [D]/[C]: Select a desired soft key. a 6. [D]/[C]: "Standby"/"Talking" a 7. [D]/[C]: "Default" a Assigning Function Keys [In standby mode] MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Key Option" a 4.
  • Page 35: Line Key

    Lines that are available can be changed using Multiline Setting. See “System Settings”, Page 99. However, when connecting to a base unit other than the KX-TGP600, you can only seize a line using this key. You cannot check the status of the lines.
  • Page 36 Before Operating the Telephones Icons Description Shows the Block Anonymous Call setting. For details about operation, see “Call Settings”, Page 100. Displayed when an Anonymous Call is specified. For details about operation, see “Call Settings”, Page 100. Displayed when Call Forwarding is specified. Displayed when Do Not Disturb (DND) is specified.
  • Page 37 <Outgoing Call Log> Phonebook> <Incoming Call Log> *1 The Line Status screen is different depending on whether connected to a KX-TGP600 or another base unit. For details, see “LINE Key”, Page 35. /[FUNCTION] for the KX-TPA65. *3 The Function Keys screen is different depending on whether connected to a KX-TGP600 or another base unit.
  • Page 38 Before Operating the Telephones R To search for an item in the Phonebook, see “Using the Phonebook”, Page 62.
  • Page 39 Before Operating the Telephones Function Menus Press or the [CENTER]/[ENTER] navigation key to display the main and sub menus. MENU Main Menu–While in Standby Mode Incoming Log (Page 41) Enters the Incoming Call Log. Ringer Volume (Page 40) Accesses the "Ringer Volume" setting. New Phonebook (Page 63) Stores a new item in the Phonebook.
  • Page 40: Function Keys

    Makes a voice announcement to the handsets or the desk phones simultaneously. *1 "Call Forward" when connected to a base unit other than the KX-TGP600. *2 "Call Park" and "Paging" are displayed only when they are enabled in settings. Contact your administrator for further information.
  • Page 41: Incoming/outgoing Call Log

    2. [D]/[C]: "Incoming Log" a *1 If "Missed Calls" is not displayed on the LCD in standby mode, this step can be skipped. When connected to a base unit other than the KX-TGP600, since "Incoming Log" is not displayed, select from "Missed Call"/"Answered Call".
  • Page 42: Parallel Mode (kx-tpa65 Only)

    Before Operating the Telephones Making a call using the Incoming/Outgoing Call Log See “Using the Incoming/Outgoing Call Log”, Page 49. Storing an item using the Incoming/Outgoing Call Log See “Storing an Item Using the Incoming or Outgoing Call Log”, Page 64. Deleting the Incoming Call Log [When the Incoming Call Log is displayed] 1.
  • Page 43: Setting The Password

    Before Operating the Telephones Setting the Password The handset/desk phone password is not set by default. You must register a handset/desk phone password (4 digits) before use. You cannot use the following features without setting a password: R Phonebook lock (See “Locking the Handset Phonebook”, Page 68). R "Manual&Password"...
  • Page 44: Selecting The Display Language

    Before Operating the Telephones Selecting the Display Language You can select the language displayed on your handset/desk phone. [In standby mode] MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Display Option" a 4. [D]/[C]: "Language" a 5. [D]/[C]: Select a language. a R The handset/desk phone will restart after changing the Display Language. R For a list of the languages that can be selected, see “Display Option”, Page 95.
  • Page 45: Power On/off (kx-tpa60 Only)

    Before Operating the Telephones Example: To enter "Anne" in Latin Mode. 2 a [E] a [G] a 6 a 6 a [E] a 6 a 6 a [E] a 3 a 3 R To switch between uppercase and lowercase, press KX-TPA60: KX-TPA65: R To enter a character located on the same dialing key as the previous character, move the cursor by...
  • Page 46 Before Operating the Telephones Going off-hook In this manual, when you see the phrase "off-hook", you can do any of the following: R Lift the corded handset off its cradle. R Press /[SP-PHONE] while the corded handset is on its cradle. This enables hands-free mode. R Press /[SP-PHONE] when using a headset.
  • Page 47: Making Calls

    Making Calls Making Calls R To enter characters, see “Entering Characters”, Page 44 R You can confirm that the number was dialed correctly before calling (Predialing) by entering the number, then KX-TPA60: Press KX-TPA65: Off-hook R To clear an entire number while predialing, KX-TPA60: Press /[XFER/CLR] for more than 1 second.
  • Page 48: Easy Dialing

    Making Calls 2. [D]/[C]: "Flash/Recall" Predialing [In standby mode] 1. Dial the number while on-hook. 2. After dialing KX-TPA60: KX-TPA65: Off-hook Making an Intercom Call Intercom calls can be made between handsets/desk phones. [In standby mode] MENU 3. [D]/[C]: Select a desired handset/desk phone. a 4.
  • Page 49 Making Calls Note R While the Hot Key’s information is displayed, you can press [D] or [C] to select another Hot Key number. R If Hot Key dialing is set to "Auto", a Hot Key number can also be dialed by pressing and holding the assigned dialing key for a specified number of seconds.
  • Page 50: Using The Phonebook

    R For details about making a call using the Handset Phonebook, see “Searching for an Item in the Handset Phonebook”, Page 66. Using the Base unit Phonebook (when connected to a base unit other than the KX-TGP600 only) [In standby mode] 2.
  • Page 51: Making A Multicast Voice Paging Call

    Making Calls Using the Remote Phonebook (when connected to a base unit other than the KX-TGP600 only) [In standby mode] 2. [D]/[C]: "Remote Phonebook" a 3. Enter the name or the first character(s) of the desired name. a 4. [D]/[C]: Select the desired item. a MENU 5.
  • Page 52: Receiving Calls

    Note R When receiving an intercom call, the Handset Name is displayed on the LCD. To answer an incoming call on a specific line (when connected to the KX-TGP600 only) /[LINE]: Display the line keys. 2. Press the dial key or [D]/[C] to select the Line number. a You can also answer a call using the following features: –...
  • Page 53: Hands-free Mode

    Receiving Calls Note R Line keys with incoming calls will be flashing green rapidly. R If "Quick Answer" is set to "On" and a brief power failure occurs while the handset is receiving a call on the charger, the following may occur: –...
  • Page 54: Answering An Intercom Call

    Receiving Calls R During a conversation in hands-free mode with the handset on the charger, lift the handset off its charger. [KX-TPA65] During a conversation in hands-free mode, go off-hook. Answering an Intercom Call 1. KX-TPA60: : Answer the page. KX-TPA65: Off-hook: Answer the page.
  • Page 55: During A Conversation

    Receiving Calls R During a conversation with a headset in default Noise Reduction mode, even if you disconnect the headset from the handset, Noise Reduction mode will continue. R During a conversation without a headset in default Noise Reduction mode, even if you connect the headset to the handset, Noise Reduction mode will continue.
  • Page 56: During A Conversation

    2. Dial the party you want to transfer to. a CALL 3. Wait until the other party answers to announce the transfer. 4. KX-TPA60: KX-TPA65: On-hook *1 When connected to a base unit other than the KX-TGP600, the operation is as follows. KX-TPA60: /[XFER/CLR] KX-TPA65: /[TRANSFER] Note...
  • Page 57: Holding A Call

    /[HOLD/MSG] KX-TPA65: / /[HOLD] To retrieve a call on hold at your line (when connected to the KX-TGP600 only) /[LINE] 2. Press the dial key corresponding to the slowly flashing green LINE indicator, or press [D] or [C] to select a slowly flashing green LINE indicator. a Holding in a System Parking Zone (Call Park) You can use this feature as a transferring feature.
  • Page 58: Three-party Conference

    R When using a KX-TPA65, /[CONF] can also be used at steps 1 and 3. Removing a Party from the Conference (when connected to the KX-TGP600 only) During a conference, you can remove other parties from the conference. However, this operation is available only during conference calls you initiate.
  • Page 59: Call Waiting

    During a Conversation 3. Press the dial key, or press [D] or [C], and then press to select the LINE number that corresponds to the party you want to disconnect. 4. KX-TPA60: /[LINE] KX-TPA65: On-hook a /[LINE] 5. Press the dial key, or press [D] or [C], and then press to select the LINE number that corresponds to the remaining party.
  • Page 60 During a Conversation 2. KX-TPA60: KX-TPA65: Off-hook To hold the current call and then talk to the new party Note R You can also answer call waiting as follows: KX-TPA60: /[HOLD/MSG] KX-TPA65: / /[HOLD] Off-hook Monitor (KX-TPA65 only) During a two-party conversation with the corded handset, you can allow other people to listen to the conversation through the speaker while you continue the conversation using the corded handset.
  • Page 61: Before Leaving Your Desk

    4. If a Forward setting is selected, enter a new forward destination number, or confirm and modify a previously set forward destination number. a *1 "Call Forward" when connected to a base unit other than the KX-TGP600. *2 Only when connected to a KX-TGP600.
  • Page 62: Using The Phonebook

    1. Handset Phonebook This Phonebook is stored in the handset/desk phone. 2. Base unit Phonebook (when connected to a base unit other than the KX-TGP600 only) This Phonebook is stored in the Base unit. 3. Remote Phonebook (when connected to the KX-TGP600 only) If your telephone company provides the remote phonebook service, you can use it.
  • Page 63: Using The Handset Phonebook

    Using the Phonebook Using the Handset Phonebook You can store up to 500 phone numbers in the handset/desk phone along with names for easy access. You can also set unique ringer patterns for different categories to identify incoming calls. All Phonebook items are stored in alphabetical order.
  • Page 64 Using the Phonebook Note R Steps 7 and 8 can be omitted if you do not want to assign a category. R Steps 9 and 10 can be omitted if you do not want to assign a default number. (The first number entered for an entry will automatically be assigned as the default number.) R The valid digits are "0"...
  • Page 65 R To enter characters, see “Entering Characters”, Page 44. R When connected to a base unit other than the KX-TGP600, a menu to select the save destination of the phonebook is displayed between steps 3 and 4. Editing a Stored Item in the Handset Phonebook...
  • Page 66 Using the Phonebook Editing Category Names You can edit the names of the categories in the phonebook. [In standby mode] MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Display Option" a 4. [D]/[C]: "Category Name" a 5. [D]/[C]: Select the desired category number (1–9). a 6.
  • Page 67 Using the Phonebook KX-TPA65: Off-hook *1 If only Handset Phonebook is permitted, this step is skipped. *2 If you push and hold [D]/[C], the next/previous items will be displayed automatically. Searching by Category If items in the phonebook have been assigned categories, you can search by category. [In standby mode] 2.
  • Page 68 Using the Phonebook Character Table when searching in the Handset Phonebook This table is only available for the dial keys when you search in the Handset Phonebook. For details about the character table for other operations, see “Character Mode Table”, Page 88. Example: To enter "ANNE"...
  • Page 69: Using The Base Unit Phonebook (when Connected To A Base Unit Other Than The Kx-tgp600 Only)

    Using the Phonebook Using the Base Unit Phonebook (when connected to a base unit other than the KX-TGP600 only) Storing an Item in the Base Unit Phonebook Storing a New Item MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Base Phonebook" a 4. Enter a name (max. 24 characters). a 5.
  • Page 70 Using the Phonebook 4. [D]/[C]: Select the desired item. a MENU 5. [D]/[C]: Select the desired phone number. a 6. [D]/[C]: "Delete" a 7. [D]/[C]: "Yes" a *1 In step 6, you can select "Delete All" instead to delete all items. Searching for an Item in the Base Unit Phonebook Searching by Name You can also search for an item in the phonebook by entering a name:...
  • Page 71: Using The Remote Phonebook (when Connected To The Kx-tgp600 Only)

    Using the Phonebook Using the Remote Phonebook (when connected to the KX-TGP600 only) You can refer to the Remote Phonebook in addition to the Handset Phonebook, if the Remote Phonebook is available. Note R We recommend setting this feature with your administrator. Contact your administrator for further information.
  • Page 72: Customizing The Telephone

    Customizing the Telephone Customizing the Telephone Changing the Handset Number and Name Display You can change the display of the handset’s number and name when the handset/desk phone is in standby mode. MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Display Option" a 4.
  • Page 73 Customizing the Telephone *1 While the Hot Key’s information is displayed, you can press [D] or [C] to select another Hot Key number. *2 To delete all items, select "Delete All" instead of "Delete". Selecting the Type of Hot Key Dialing You can select one of 2 types of Hot Key Dialing for each assigned Hot Key.
  • Page 74 Customizing the Telephone c. Enter a time of day using the Navigator Keys and/or dial keys. a 6. Enter a text message to be displayed when the Memo Alarm occurs. a 8. "Save" a Note R For details about entering characters, see “Entering Characters”, Page 44. R When entering a time of day, press [AM/PM] to toggle between AM or PM.
  • Page 75 Customizing the Telephone 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: Select the main item. a Main Item Sub Item Page Incoming Option Ringer Volume Ringer Type Ring On Charger Page Memo Alarm Power Save Headset Ringer Talk Option Noise Reduction/ Speaker Volume Receiver Volume Page Voice Clarity Headset Volume...
  • Page 76 4. [D]/[C]: "Block Caller ID" a 5. [D]/[C]: Select a desired line. a 6. [D]/[C]: Select a blank line. a 7. Enter the phone number (32 digits max.). a Editing the phone numbers to reject (when connected to the KX-TGP600 only) MENU...
  • Page 77: Web User Interface Programming

    MENU 6. [D]/[C]: Select a desired phone number. a 7. [D]/[C]: "Edit" a 8. Enter the phone number. a Deleting the phone numbers to reject (when connected to the KX-TGP600 only) MENU 2. [D]/[C]/[F]/[E]: 3. [D]/[C]: "Call Settings" a 4. [D]/[C]: "Block Caller ID" a 5.
  • Page 78 Customizing the Telephone R Handset and Line Number select for making call R Phonebook import and export Note R Each time you want to access the Web user interface, you must enable Web programming (Embedded Web). See “Other Option”, Page 97.
  • Page 79: Installation And Setup

    Installation and Setup Installation and Setup Note R Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. WARNING R To reduce the risk of fire or electric shock, do not overload AC outlets and extension cords.
  • Page 80 Installation and Setup R High Position ® Low Position PUSH PUSH R Low Position ® High Position PUSH PUSH Removing the Stand (KX-TPA65) Tilt the stand in the direction indicated while pushing the PUSH marks with both hands. PUSH PUSH...
  • Page 81: Connections

    Connect the AC adaptor and the Ethernet cable to the base unit. PQLV219xx R The initial setting for the KX-TGP600 IP address is "DHCP—Auto". For information about your network environment, contact your administrator. For details, see “Network Settings”, Page 98.
  • Page 82: Charging The Batteries

    AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. R Fasten the AC adaptor cord to the cord holder. R Use only the included Panasonic AC adaptor. Battery Installation Open the battery cover, insert the batteries, and close the cover as indicated below.
  • Page 83: Wall Mounting

    R Make sure that the wall and the fixing method are strong enough to support the weight of the unit. KX-TGP600 (Base unit) 1. Drive the screws into the wall either 55 mm (2 5/32 in) apart, and mount the unit on the wall.
  • Page 84 Installation and Setup 5. Drive the screws into the wall either 83 mm (3 1/4 in) or 100 mm (3 15/16 in) apart, and mount the unit on the wall. *1 AC adaptor *2 Handset Cord *3 Washer *4 Drive the screw to this point. *5 83 mm (3 1/4 in) *6 100 mm (3 15/16 in) R You can find a wall mounting template at the end of this manual.
  • Page 85: Updating The Software

    Registering/Deregistering a Handset/Desk Phone to the KX-TGP600 Registering a Handset/Desk Phone to the KX-TGP600 You can register a handset/desk phone to up to 4 base units. You can register a base unit to up to 8 handsets/desk phones (KX-TPA60/KX-TPA65/KX-UDT series).
  • Page 86 Installation and Setup 1. Base unit: a. Press and hold the handset locator button for about 3 seconds. The STATUS indicator on the base unit will flash red (slow flashing). 2. Unregistered handset/desk phone: [When adding a new handset/desk phone] R Easy registration In standby mode, press and hold until displaying "Please Wait…".
  • Page 87 4. Handset/desk phone: Select a handset/desk phone. a Registering/Deregistering the Handset/Desk Phone to a Base Unit Other than the KX-TGP600 Registering the handset/desk phone The base unit operations/settings should be performed according to the base unit’s instructions. Handset/desk phone registration using the base unit 1.
  • Page 88: Appendix

    Appendix Appendix Character Mode Table KX-TPA60/KX-TPA65 (Suffix: [none/C]) ABC (Latin) +ÀÂ (Extended 1) 0–9 Keys (Numeric) Upper Lower Upper Lower Space B & ’ ( ) G , – . / 1 Space B & ’ ( ) G , – . / 1 A B C 2 a b c 2 D E F 3...
  • Page 89 Appendix 0–9 ΑΒΓ AÄÃ SŚŠ Keys (Latin) (Numeric) (Greek) (Extended 1) (Extended 2) D E F 3 Δ Ε Ζ 3 d e f 3 δ ε ζ 3 G H I 4 Η Θ Ι 4 g h i 4 η...
  • Page 90 Appendix АБВ 0–9 AÄÃ SŚŠ Keys (Cyrillic) (Numeric) (Latin) (Extended 1) (Extended 2) А Б В Г 2 A B C 2 а б в г 2 a b c 2 Д Е Ё Ж З 3 D E F 3 d e f 3 д...
  • Page 91 Level 1–6 Ringer Type (when Ringer Pattern Line 1–8: Ringtone 1–19, 25–32 using a Selects the ringtone for each Ringtone 1–8 KX-TGP600) Intercom Ring: type of call. R Line 1–8 Ringtone 9 R Intercom Ring Private Ring: R Private Ring Ringtone 1 (Category 1–9)
  • Page 92 Appendix Talk Option Sub Item Description Setting Default Noise Reduction/ Activate/deactivate Noise Voice Clarity Reduction. (KX-TPA60 only) Speaker Volume Adjusts the rear speaker Level 1–6 Level 3 volume. Receiver Volume Adjusts the receiver volume. Level 1–6 Level 2 Headset Volume Adjusts the headset speaker Level 1–6 Level 2 volume.
  • Page 93 Appendix Key Option Sub Item Description Setting Default Function Key Edits the Function Key list. Suffix: CE/UK/AL/RU/LA/ 1: Redial 2: Fwd/DND Redial 3: Conference 4: Auto Answer Fwd/DND 5: Flash/Recall Conference 6: Incoming Log Auto Answer 7: Outgoing Log Flash/Recall 8: Phonebook Incoming Log 9: —...
  • Page 94 "Auto" is pressed and held. *1 "Call Forward" when connected to a base unit other than the KX-TGP600. *2 Not available when connected to a base unit other than the KX-TGP600. *3 "Call Park", "Pause" and "Paging" are displayed only when they are enabled in settings. Contact your administrator for further information.
  • Page 95 Appendix Display Option Sub Item Description Setting Default Language Selects the display language. Suffix: CE/UK/AL Auto Up to 10 languages can be Auto downloaded from the base unit. English The feature depends on your Deutsch phone system. Contact your Español administrator for further FRANÇAIS information.
  • Page 96 Current+Scanned *1 Cannot be selected when connected to a base unit other than the KX-TGP600. *2 The keypad backlight is available only for the KX-TPA60. *3 Not displayed when connected to a base unit other than the KX-TGP600.
  • Page 97 *3 If a password has not already been set, you can skip the first step. *4 For details about setting the password, see “Setting the Password”, Page 43. *5 Not displayed when connected to a base unit other than the KX-TGP600.
  • Page 98 Appendix System Setting Menu Layout (when connected to the KX-TGP600) Status Sub Item Description Setting Default Line Status Displays the line status. Registered/Registering/ — (NULL) Firmware Version Selects which is shown on the –Base Station — display the model number and –Handset...
  • Page 99 Appendix Sub Item Description Setting Default IPv6 Settings Specifies the IPv6 settings. DHCP–Auto DHCP Auto Manual –DNS 1 –DNS 2 –DNS 1 –DNS 2 Static –IP Address –Prefix –Default Gateway –DNS 1 –DNS 2 LLDP Specifies the LLDP settings. VLAN Specifies the VLAN settings.
  • Page 100 Appendix Sub Item Description Setting Default MultilineSetting Specifies the multiline mode. Incoming Call: Incoming Call Handset 1–8 Line 1–8 Outgoing Call: Handset 1–8 Line 1–8 Outgoing Call Default Line: Handset 1–8 Line 1 Line 1–8 Default Line Specifies the ID and password Not stored Authentication –ID...
  • Page 101 *2 In a phone number that exceeds 32 digits, the exceeding digits will not be displayed. *3 If the Xsi’s service is available, you can select these items. Contact your administrator for further information. System Setting Menu Layout (when connected to a base unit other than the KX-TGP600) System Settings Sub Item Description...
  • Page 102: Specifications

    Appendix Specifications KX-TGP600 (Suffix: all) Item Specifications Power Supply AC adaptor/PoE (IEEE 802.3af) Maximum Power Consumption 2.6 W Operating Environment 0 °C (32 °F) to 40 °C (104 °F) Ethernet Port (LAN) 1 (RJ45) Ethernet Interface 10Base-T/100Base-TX (Auto/100MB-FULL/100MB-HALF/10MB-FULL/10MB-HALF) CAT-iq Wideband Codec G.722/G.722.2...
  • Page 103 "Low" position: 192 mm ´ 185 mm ´ 150 mm (7.56 in ´ 7.28 in ´ 5.91 in) Weight 117 g (0.26 lb) 675 g (1.49 lb) RF Specifications KX-TGP600/KX-TPA60/KX-TPA65 Item USA, Canada Latin America Other countries/areas Wireless Interface DECT 6.0...
  • Page 104: Troubleshooting

    Appendix Troubleshooting Problem Possible Cause Solution The handset does not The battery is drained. Charge the battery fully. work. For details, see "Charging the Batteries" on Page 82. The power is off. R Turn it on. For details, see "Location of Controls"...
  • Page 105 Appendix Problem Possible Cause Solution The handset stops An unknown error has occurred. R Turn the handset off, and then working during turn it back on. operation. For details, see "Location of Controls" on Page 18. R Re-insert the battery and try again.
  • Page 106 Appendix Problem Possible Cause Solution While charging the The temperature of the battery Confirm that the area where the battery, the LED being charged is outside of handset is being charged is indicator blinks normal limits. between 5 °C (41 °F) and 40 °C rapidly, but the (104 °F), and wait for the battery’s handset does not...
  • Page 107: Error Messages

    Appendix Error Messages Error Message Possible Cause Solution Register Unit The handset/desk phone has Consult your dealer. been cancelled or the handset/ desk phone has not been registered. No Service The handset/desk phone is out of Move closer to the base unit. range.
  • Page 108 One screw here One screw here WALL MOUNTING TEMPLATE 1. Drive the screws into the wall as indicated. 2. Hook the unit onto the screw heads. Note: Make sure to set the print size to correspond with the size of this page. If the dimensions of the paper output still deviate slightly from the measurements indicated here, use the measurements indicated here.
  • Page 109 Notes...
  • Page 110 Notes...
  • Page 111 Notes...
  • Page 112 Web Site: http://www.panasonic.ca Copyright: This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic System Networks Co., Ltd.

This manual is also suitable for:

Kx-tpa60Kx-tpa65Kx-tgp600gKx-tgp600cegKx-tgp600ukg

Comments to this Manuals

Symbols: 0
Latest comments:
  • Alida Oct 03, 2018 12:42:
    On the top right hand of my handset there is a bell with a line through it. People can't call through to this phone. How do I fix this?