Table of Contents
Advertisement
Operation Guide 5424
3. Press C.
This enters the 6 Day Indicator home position
adjustment mode.
4. Check the 6 Day Indicator to confi rm that it is 1, which
1
is its home position.
If the 1 is not in the center of the 6 Day Indicator,
rotate the crown to center it.
Rotating the crown three full consecutive turns
clockwise will cause the 6 Day Indicator to start
6
changing in a forward direction (increment).
To stop 6 Day Indicator movement, press any button.
5. Push the crown back in to return to the Timekeeping Mode.
This will cause the hands to return to their normal positions and resume regular
timekeeping. Wait until everything stops moving before performing any other
operation.
E-70
The time setting is being adjusted following a successful auto time calibration
signal receive operation (page E-21).
■ Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-18). Do not perform any operation
until the hands return to their normal positions (in about 15 minutes). The hands
should return to their correct positions when normal operation returns. To help power
recover, leave the watch in a location where it is exposed to light.
■ The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it,
if necessary (page E-38).
■ The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is
possible, see "To confi gure Home City settings" (page E-38).
E-72
Charging
■ The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3 (page E-17). Continue exposing
the watch to light until the 2 Second Hand starts moving normally (at one-second
intervals).
■ The 2 Second Hand starts to move at one-second intervals, but then suddenly
returns to moving at two-second intervals.
The watch probably is not suffi ciently charged yet. Continue keeping it exposed to
light.
Time Calibration Signal
The information in this section applies only when LONDON (LON), PARIS (PAR),
ATHENS (ATH), HONOLULU (HNL), ANCHORAGE (ANC), LOS ANGELES (LAX),
DENVER (DEN), CHICAGO (CHI), NEW YORK (NYC), HONG KONG (HKG), or
TOKYO (TYO) is selected as the Home City. You need to adjust the current time
manually when any other city is selected as the Home City.
E-74
■ The current time setting changes after I set it manually.
You may have the watch confi gured for Auto Receive of the time calibration signal
(page E-28), which will cause the time to be adjusted automatically according to your
currently selected Home City. If this results in the wrong time setting, check your
Home City setting and correct it, if necessary (page E-38).
■ The current time setting is off by one hour.
Possible Cause
Remedy
Use the procedure under "To switch
The period when summer time is applied
between standard time and summer
in the location where you are using the
time manually" to switch from AUTO
watch may be different from the period
to STD (for standard time) or DST (for
set for your currently selected Home City.
summer time).
E-76
■ Signal reception is being performed successfully, but the time and/or day is
wrong.
Possible Cause
Remedy
Check your Home City setting and
Your Home City setting is wrong.
correct it, if necessary.
The watch may have been exposed to
magnetism or strong impact, which has
Adjust the watch's hand and day
caused problems with proper hand and
indicator home positions.
day indicator alignment.
E-78
Troubleshooting
Hand Movement and Position
■ I lost track of what mode the watch is in.
Refer to "Mode Reference Guide" (page E-34). To return directly to the Timekeeping
Mode, hold down C at least two seconds.
■ The 2 Second Hand is moving at two-second intervals.
■ All the watch's hands are stopped at 12 o'clock and none of the buttons work
(2 Second Hand stopped at 57, 58, 59, or 00).
Power may be low. Expose the watch to light until the 2 Second Hand starts moving
normally, at one-second intervals (page E-17).
■ The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
The watch is recovering from a sleep state (page E-20).
The period when summer time is applied in the location where you are using the
watch may be different from the period set for your currently selected Home City.
Use the procedure under "To switch between standard time and summer time
manually" (page E-41) to switch from AUTO to STD (for standard time) or DST (for
summer time).
■ The time and date settings are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day indicator alignment. Adjust the
watch's hand and day indicator home position alignment (page E-67).
■ The 2 Second Hand indicates N (NO) when I check the result of the latest
receive operation.
Possible Cause
You are wearing or moving the watch,
or performing a button operation
during time calibration signal receive
operation.
The watch is in an area with poor
reception conditions.
You are in an area where signal reception
is not possible for some reason.
The alarm time was reached during time
calibration signal reception.
The calibration signal is not being
transmitted for some reason.
■ Auto Receive is not performed or I cannot perform Manual Receive.
Possible Cause
The watch is in the World Time Mode.
The watch is in the Stopwatch Mode.
Page
Your Home City setting is wrong.
Auto time calibration signal reception
E-41
is OFF.
A countdown timer operation is in
progress.
There is not enough power for signal
reception.
World Time
■ The indicated World Time is wrong.
Page
There is a problem with your Home City settings.
Check your Home City settings.
E-31
E-38
See "To confi gure Home City settings" (page E-38).
■ The indicated World Time is one hour off.
E-67
The daylight saving time (summer time) setting for the World Time city is wrong.
See "To view the time in another time zone" (page E-51).
Alarm
■ The alarm does not sound.
Power may be low. Expose the watch to light until the 2 Second Hand starts moving
normally, at one-second intervals (page E-17).
The time setting is wrong in terms of a.m. and p.m.
The crown may be pulled out. Push the crown back in.
E-71
E-73
Remedy
Page
Keep the watch in an area where
reception conditions are good while time
E-26
calibration signal receive operation is
being performed.
See "Approximate Reception Ranges".
E-23
The alarm sounded during time
calibration signal reception, causing
—
reception to be canceled.
Check the website of the organization
that maintains the time calibration
signal in your area for information about
—
its down times.
Try again later.
E-75
Remedy
Page
Auto Receive is not performed while
the watch is in the World Time Mode or
E-28
Stopwatch Mode. Hold down C at least
E-35
two seconds to enter the Timekeeping
Mode.
Check your Home City setting and
E-21
correct it, if necessary.
E-38
Check the auto time calibration signal
E-31
reception setting.
In the Countdown Timer Mode, stop the
timer operation and then return to the
E-62
Timekeeping Mode.
Expose the watch to light to charge it.
E-13
E-77
E-79
Advertisement
Table of Contents
