DeView 690HTVL-E User Manual

690HTVL-E Day / Night
Color Camera
Emissions FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR22
ANSI C63.4
Immunity CE: EN50130-4
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against armful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifications not expressly approved by seller.
The party responsible for FCC compliance could void the user's authority to operate the equipment and could create a
hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
without prior notice.
•
Quick install adaptor x 1 (Optional)
•
Torx driver x 1
• D5 fixing screws x 3
• T6 fixing screw (for T6 fixing screw) x 1
•
Wall plugs x 3
• Power lead x 1
• Cable entry sealing plug
(1/2", for quick install adaptor use) x 1
Cable entry sealing plug
•
(3/4" ,for dome base use) x 1
General Specifications
TV System NTSC
Image Sensor Pixim Seawolf 1/3" Sensor
Effective Picture Element 758(H)x540(V)
Scanning Frequency 60Hz
Resolution
Min. Illumination 50IRE: 0.1Lux F1.2
102dB Typical, 120dB Max.
Wide Dynamic Range Control
S/N Ratio
Video Output 1.0Vpp 75 BNC unbalanced
Mount Type Surface and Flush Mount
Power Source 12VDC ±10% / 24VAC±20%
Power Consumption
Operating Temperature -10°C~+50°C
Storage Temperature -30°C~+80°C
Functional Specifications
Exposure Control Gain Control, Shutter Control, Wide Dynamic, Manual
Digital Slow Shutter
Backlight Compensation
Digital Noise Reduction 3D Motion Adaptive (0~255)
RoHS
White Balance Control ATW Normal, AWB
Standard Range 2800k~9100k
AWB
EX Range 2000k~11000k
Day & Night SDN (ON, OFF, AUTO)
Sync System
Gamma Compensation
F p i l H o z i r n o
Digital PTX
Focal Length
3.0~9.0mm
F-No.
F1.4
Iris Range
F1.4~F360
Minimum Object Distance 0.5m
Diagonal
115.4º~39.8º
Field of View Horizontal 90.3º~31.9º
Vertical
66.4º~23.9º
V531-DH011-S00
Ver.08/2011
PAL
758(H)x540(V)
50Hz
690 HTVL-E
50dB
2.88 W Max
up to 32X
Full Range
INT / L.L OSD control board
0.45
l a t V ; r e c i t ; l a o B h t
1X~8X
Camera adjustments and programming
In addition to the levers for Focus (A) and Field of View (B),
3.3~12mm 9~22mm
all settings are made by keys on the OSD service board.
F1.4 F1.4
F1.4~F360
F1.4~F360
1. With power applied to the camera and a video monitor connected, press and hold
0.5m 1m
the MENU key for three seconds to access the top level menu. A map of the menu
125.7º~29.9º 41.9º~16.3º options are shown in the following Camera OSD Menu.
89.8º~23.9º 32.1º~13.1º
2. Use the arrow keys on the control board to navigate around the OSD menu and use the
63.6º~17.9º 23.3º~9.8º
MENU key to confirm your selections.
3. Once programming is complete choose Exit from the menu,
otherwise any changes made will be lost.
4. If required, the camera can be reset to factory defaults by selecting
RESET in the OSD menu.
Note:
DPC (Dead Pixel compensation): The camera has a feature that can cover most dead pixels
that could occur over time. Select DPC under the special menu, Cover the lens to black it
out then press the menu key - this may take up to 30 seconds to complete,.
Once complete the camera will automatically take you to back to the menu structure.
If you gain access to the DPC menu and do not want to perform the function,
press the up or down button to escape and you will be returned to the previous screen.
Presets
A
Exposure
B
A: Focus Adjuster
B: Field of View Adjuster
White balance
Viewing
Setup
C: Control Board Connector
Save/Restore
*Please refer to the following "Camera
Adjustment" for more information about
the connection.
Exit Menu
,
WD-Normal
Indoor
Normal
Outdoor
D/N Threshold
AUTO
D/N Control
Day/Night Setup
D/N Limit
D/N Switch
D/N Delay
Off
On
Night Mode B/W + Burst
B/W
Shutter Mode
Auto
Off
Mode ATW Normal
ATW Extended
Kelvin
AWB Manual
R/B
PTZ
FLIP
Monitor
LCD GAMMA
CRT
Iris Manual/DC
Lens Select
DC Gain
AI Threshold
Video I/O Video Standard PAL/NTSC
LL V-Phase
SYNC
INT
INT2
Up-Left
Title Display On/Off
Up-Center
Title
Camera Title
UP-Right
Title Position Down-Left
Down-Right
WD-Normal
Meter Mode Normal Safe Area
Backlight
CTR Spot
Normal Meter Presets Lower 1/3
Presets
Adjust Normal
Enable Zones WD-Normal
Zones
Adjust WD-Normal Safe Area
Adjust Safe Area CTR Spot
Lower 1/3
Adjust CTR Spot
Restore User Settings
Adjust Lower 1/3
Save User Settings
Restore Factory Settings
Reset Camera
System Info