Summary of Contents for Rollplay 12V Chevy Silverado W461-C
Page 1
12V Chevy Silverado Owner’s Manual and Assembly Instructions (2-Person Assembly Recommended) Model #: W461-C W461-C02 W461-C03 W461-CO2-F Read and understand the entire manual before assembly and operation. The vehicle must be assembled by an adult who has read and understands the instructions. Made in China.
Introduction Thank you for purchasing this vehicle from Aria Child. We hope the rider enjoys it for miles to come. Please read this instruction guide carefully before assembling and operating the vehicle. Please have your model number and serial number ready before calling. Please have proof of purchase.
Page 3
IMPORTANT! YOU MUST CHARGE THE BATTERY FOR 24 HOURS BEFORE FIRST USE! Charge the battery after each use. Charge the battery at least once a month, even if the vehicle is not in use. DO NOT RETURN THIS ITEM TO THE STORE! Contact Customer Service if you need assistance or replacement parts.
Table of Contents Safety ............5 Parts ............7 Charging Instructions .......8 Assemble the Rear Support Bars ....9 Install the Rear Support Bars ....10 Install the Rear Wheel Axle .....11 Install the Gear Boxes ......12 Assemble the Rear Wheels .....13 Assemble the Front Wheels ....14 Attach the Truck Bed ......15 Attach the Mirrors ........16 Attach the Windshield and Dashboard ..17...
Safety WARNING: SAFETY RIDING RULES PREVENT INJURIES AND DEATHS: NEVER LEAVE CHILD UNATTENDED. ALWAYS keep child in view when child is in vehicle. Direct adult supervision is REQUIRED. NEVER use on roadways, near cars, on or near steep inclines or steps, swimming pools or other bodies of water.
Page 6
Safety (Continued) WARNING: BATTERY SAFETY • Battery posts, terminals and related accessories contain lead and lead compound (asic) chemicals known to the state of California to cause cancer, reproductive harm, and are toxic and corrosive. DO NOT open the battery. • Contact exposure to battery leakage (lead acid) may cause serious injury.
Charging Instructions YOU MUST CHARGE THE BATTERY FOR 24 HOURS BEFORE THE FIRST USE! ONLY AN ADULT SHOULD HANDLE THE BATTERY AND CHARGER. Connect the Battery: 1. Ensure the vehicle is stopped and turned off. 2. Unlock and remove the seat. 3.
Assemble the Rear Support Bars 2-Person Assembly Recommended 1. Locate the right (9) and left (10) support bars and the rear support lateral bar (11) 2. Insert the rear support lateral bar into the square slots on the rear support side bars 3.
Install the Rear Support Bars 1. Carefully flip the truck body on its back for easier assembly (use a soft surface to avoid any scratches or damage) 2. Slide the assembled rear support bars into the square holes on the back of the truck body 3.
Install the Rear Wheel Axle 1. Locate the rear wheel axle (12) 2. Remove the nut and washer from both sides of the rear axle 3. Slide the rear axle horizontally through the rear support system as pictured 4. Make sure the axle is centered before and during rear wheel installation...
Install the Gear Boxes 1. With the truck body still on its back, locate the two holes on either side of the truck body with the white gearbox connector and yellow gearbox connector 2. Slide the left gear box (1) onto the rear axle with the white gears facing out until it sits completely in the gear box bracket and the silver cylindrical end fits completely into the hole that leads to the battery compartment 3.
Assemble the Rear Wheels Helpful Tip: If you encounter trouble fitting both wheels onto the rear axle, then your rear wheel axle may need to be realigned. Remove both wheels from the rear wheel axle. Using two hands, push down on the rear wheel axle and slide it gently toward the side of the vehicle that needs more room.
Assemble the Front Wheels 1. Slide a thick washer onto the front axle 2. Slide the front wheel onto the front axle (15). The concave side should face inward 3. Slide the thin washer onto the front axle 4. Using the hex wrench, fasten the nut on the end of the axle and tighten until you can not tighten any more 5.
Attach the Truck Bed 1. Turn the truck right-side up so that the wheels are on the ground 2. Match the 9 screw holes on the truck bed with the holes on the truck body 3. Align the holes and fasten all screws securely with a screwdriver...
Attach the Mirrors 1. Remove the mirrors (4 and 5) from the plastic bags 2. Remove the screw and nut from the mirror assembly 3. Align the hole on the mirror with the hole on the truck 4. Insert the screw into the hole and fasten the nut with a screwdriver to secure the mirror 5.
Attach the Windshield and Dashboard 1. Attach the 2 wire connectors coming from the dashboard (17) body (located in the dashboard) to the 2 wire connectors attached to the truck body 2. Match the plastic inserts on the dashboard with the four slots on the truck body and insert into the truck body at a 45 degree angle 3.
Attach the Steering Rod 1. Locate the steering rod (25) 2. Insert the straight end of the steering rod into the steering rod hole on the underside of the dashboard. The steering rod should slide all the way through the dashboard 3.
Assemble the Steering Wheel Helpful Tip: Have one person hold the steering rod in place to prevent it from sliding down while the other person attaches the steering wheel 1. Use a Phillips head screwdriver to remove the screw on the battery compartment of the steering wheel 2.
Attach the Doors Truck frame post 1. Align the doors with the interior facing the inside of the truck 2. Position the hole on the door over the hole on the truck body and slide the post on the bottom of the door into the hole on the truck body side 3.
Attach the Tailgate 1. Keeping the tailgate horizontal, align the tailgate with the holes on the truck bed 2. Once the tailgate is completely aligned with the slots on the bed, lift the bed door up until it clicks into place...
Battery Attachment 1. Plug in the red battery connector on the 12V battery with the red engine connector after charging the battery for 24 hours. 2. Note: This product uses a recoverable fuse which will automatically cut power to the truck if the current is overflowed. The truck will recover and properly function again in 5 to 10 seconds...
Attach the Seat 1. Align the seat over the battery compartment 2. Ensure the locking mechanism aligns with the holes 3. Slide the hooks onto the back of the seat into the slots on the truck body 4. Turn the thumbscrew clockwise until it faces the lock position to properly secure in place...
Operation Instructions 1. Press the left and right steering wheel buttons for horn (a) and engine sounds (b) 2. Turn the power switch to turn on the truck. The power indicator light will turn on when the truck is on. Turn the power switch again to turn off the truck.
Maintenance Important Battery and Charger Information • Only an adult who has read and understands the safety warnings may handle and operate the battery and battery charger. Keep away from children. • Charge the battery for 24 hours before using the vehicle for the first time.
General Care • Regularly inspect all vehicle parts to ensure they are in good working condition. • Regularly inspect the charger, cord, plug, and other related parts for damage. • Remove any damaged parts and immediately contact Customer Service for replacement parts. See Service and Repairs on Page 23 for more information.
Troubleshooting Guide Completely read through the manual and troubleshooting guide before contacting Customer Service. Problem Potential Cause Solution Vehicle does not run Battery is low Recharge the battery Thermal fuse tripped This product uses a recoverable fuse which will automatically cut power to the truck if the current is overflowed.
Page 28
Problem Potential Cause Solution Vehicle needs a push to Loose wires or loose Ensure the battery connectors start connectors are securely attached. If wires are loose, contact Consumer Service for repairs “Dead spot” on motor A “dead spot” means electricity is not being delivered to the terminal.
FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Service and Repairs Do not return this vehicle to the store. If your product requires service, repairs or replacement parts, please contact Aria Child Customer Service. Hours: 9 AM - 5 PM (CST), Monday - Friday 888-982-9309 Phone: 1- Email: customerservice@ariachild.com Web: www.ariachild.com For a list of available replacement parts, please visit www.ariachild.com.
Warranty Aria Child 12-Volt Limited Warranty • One-year limited warranty from the date of purchase with proof of purchase from an Aria Child certified retailer. • Six month limited warranty on the 12-Volt battery with proof of purchase from an Aria Child certified retailer.
Product Registration Fill out the form below and mail it to: Aria Child 1131 W. Blackhawk St. Second Floor Chicago, IL 60642 OR fill out the form online at www.ariachild.com We will use the information provided only for your warranty. We will not sell, rent or share your personal information.