Portwell may make supplement or change in the products described in this document at any time. Updates to this manual, technical clarification, and answers to frequently asked questions will be shown on the following web site : http://www.portwell.com.tw/.
Ethernet, one micro SD socket and Six USB ports (two for 2.0, four for 3.0). It also built with DC 12V or ATX 12V input. Base on leading Intel® Atom solution, NANO-6060 is a compact and low power dissipation board for Digital Signage, Digital Security Surveillance (DSS) and Medical applications…etc.
Page 5
PCI Express slot - Support one PCIE x1 slot High Drive GPIO - On-board programmable 8-bit Digital I/O interface System Monitoring Feature - Monitor system temperature and major power sources. Outline Dimension (L x W) - 120mm(4.72’’) x 120mm(4.72’’) NANO-6060 User’s Manual...
System Overview System Architecture All of details operating relations are shown in NANO-6060 System Block Diagram. NANO-6060 System Block Diagram NANO-6060 User’s Manual...
Hardware Configuration This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on NANO-6060 are in the proper position. The default settings shipped from factory are marked with an asterisk (♣).
Page 10
Hardware Configuration JP1: GPIO4~7 Voltage Level Selection Function 1-2 Short 5V ( output ) 2-3 Short 3.3V ( Input ) JP3: LVDS Link Selection Function Short Dual Link Open Single Link NANO-6060 User’s Manual...
Page 11
Function 1-3 Short VCC3 3-5 Short 3-4 Short +12V JP6: PANEL BACKLIGHT Selection Pin No. Signal Description 1-3, 2-4 5V, Active High 1-3, 4-6 12V, Active High 3-5,2-4 5V, Active Low 3-5,4-6 12V, Active Low NANO-6060 User’s Manual...
Page 12
Clear CMOS Contents JP10 : LVDS Color Depth and Data Mapping JP10 Function 2-4 Short 8-bit LVDS , VESA mapping 1-3 , 2-4 Short 8-bit LVDS , JEIDA mapping 1-3 Short 6-bit LVDS , VESA and JEIDA mapping NANO-6060 User’s Manual...
Page 17
5V always USB- USB- USB+ USB+ Ground Ground Key( no pin ) Note: 5V Dual is always available. It's supplied by either 5V VCC power source in normal operation mode or 5V standby power source in standby mode. NANO-6060 User’s Manual...
Step 1 : Check all jumpers setting on proper position Step 2 : Install and configure CPU and memory module on right position Step 3 : Place NANO-6060 into the dedicated position in the system Step 4 : Attach cables to existing peripheral devices and secure it WARNING Please ensure that mother board is properly inserted and fixed by mechanism.
3.3.1 Chipset Component Driver NANO-6060 uses state-of-art Intel® BayTrail-I Soc. It’s a new chipset that some old operating systems might not be able to recognize. To overcome this compatibility issue, for Windows Operating Systems such as Windows 8, please install its INF before any of other Drivers are installed.
Clear CMOS Operation The following table indicates how to enable/disable Clear CMOS Function hardware circuit by putting jumper in the board. JP7/JP8 : CMOS Clear JP7/8. Function 1-2 Short Normal Operation 2-3 Short Clear CMOS Contents NANO-6060 User’s Manual...
Page 27
= inportb (EC_DATA); return data; int main () unsigned char d2; printf("\n\n"); printf("NANO-6060 GPIO TEST Program v1.0\n"); printf("Please short the following pins with 2.54mm-pitched jumper on JP8\n"); printf("PIN 1,3,5,7 is output ; PIN 2,4,6,8 is input\n"); printf("GPIO1 ---- GPIO5\n");...
Page 28
((d2 & 0x40) == 0) printf ("GPIO72->GPIO76 test ok !! (pull low)\n"); else printf ("GPIO72->GPIO76 test fail (pull high)\n"); if ((d2 & 0x80) == 0) printf ("GPIO73->GPIO77 test ok !! (pull low)\n"); else printf ("GPIO73->GPIO77 test fail (pull high)\n"); return 0; NANO-6060 User’s Manual...
Chapter 4 BIOS Setup Information NANO-6060 is equipped with the Phoenix BIOS stored in Flash ROM. These BIOS has a built-in Setup program that allows users to modify the basic system configuration easily. This type of information is stored in CMOS RAM so that it is retained during power-off periods.
The date format is <Day>, <Month> <Date> <Year>. Use [+] or [-] to configure system Date. System Time View or set system time The time format is <Hour> <Minute> <Second>. Use [+] or [-] to configure system Time. NANO-6060 User’s Manual...
Page 31
Troubleshooting System Information Display System Information Boot Features Select Boot features NANO-6060 User’s Manual...
Page 32
Choices: Disable, Enable. Console Redirection Enable/Disable Universal Console Redirection Choices: Disable, Enable. Allow Hotkey in S4 Resume Enable hotkey detection when system resuming from Hibernate state Choices: Disable, Enable. UEFI Boot Enable the UEFI boot. Choices: Disable, Enable. NANO-6060 User’s Manual...
Troubleshooting Advanced Setup Warning: Setting items on this screen to incorrect values may cause system to malfunction! Advanced CPU Configuration NANO-6060 User’s Manual...
Page 35
If bi-direction is enabled, external agents can drive PROCHOT# to throttle the processor Choices: Disable, Enable. VTX-2 To enable or disable the VTX-2 Mode support Choices: Disable, Enable. Enable/Disable TM1 Choices: Disable, Enable. Enabled/Disable Digital Thermal Sensor Choices: Disable, Enable. NANO-6060 User’s Manual...
Page 36
Intel® Turbo Boot Technology Enable to automatically allow processor cores to run faster than the base operation frequency if it’s operating below power, current, and temperature specification limits. Choices: Disable, Enable. C-States Enable/Disable C States Choices: Disable, Enable. NANO-6060 User’s Manual...
Page 37
Enable GOP Driver will unload VBIOS; Disable it will load VBIOS Choices: Enable, Disable. IGD Configuration (Show only) Integrated Graphic Device (Show only) Enable: Enable Integrated Graphics Device (IGD) when selected as the Primary Video Adapter. Disable: Always disable IGD Choices: Disable, Enable. NANO-6060 User’s Manual...
Page 38
Choices: 640 x 480, 800 x 600, 1025 x 768, 1280 x1024, 1400 x1050, 1600 x 1200, 1360 x768, 1680 x 1050, etc. IGD Boot Type Select preference for Integrated Graphics Device (IGD) display interface used when system boots Choices: Auto, VGA Port, DP, LVDS. NANO-6060 User’s Manual 4-10...
Page 39
Select the LCD Panel scaling option used by Internal Graphic device Choices: Auto, Centering, Stretching. System Component PMIC Congfiguration PNP Setting Select PNP setting mode, Disable, Performance, Power or Power&Performance mode. Choices: Disable, Performance, Power, Power & Performance NANO-6060 User’s Manual 4-11...
Page 41
Mode of operation of xHCI controller Choices: Smart Auto, Auto, Enable, Disable. USB OTG Support Enable/Disable USB OTG Support Choices: Disable, PCI Mode, ACPI Mode. EHCI Controller (Show only) Control each of the USB ports (0~9) disabling Choices: Enable, Disable. NANO-6060 User’s Manual 4-13...
Page 42
LPE Audio Support Choices: Disable, LPE Audio PCI mode, LPE Audio ACPI mode. Audio Controller Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be unconditionally enabled. Choices: Disable, Enable. NANO-6060 User’s Manual 4-14...
Page 43
Warning: OS may not boot if this setting is changed after OS install. Choices: IDE, AHCI. Serial Port 0/1 Hot Plug Capability If enabled, SATA port 0/1 will be reported as Hot Plug capable. Choices: Enable, Disable. NANO-6060 User’s Manual 4-15...
Troubleshooting APM Configuration Power On By RTC Alarm Choices: Disable, Enable. Wake on LAN1 Choices: Disable, Enable. Wake up by Ring Choices: Disable, Enable. NANO-6060 User’s Manual 4-20...
Set User Password (Show only) Set or clear the User account’ password. Supervisor Hint String (Show only) Press Enter to type User Hint String. Min. password length Set the minimum number of characters for password (1-20). NANO-6060 User’s Manual 4-21...
Boot Priority Order Keys used to view or configure devices: ↑ and ↓ arrows Select a device. ‘+’ and ‘-‘move the device up or down. ‘Shift + 1’ enabled or disables a device. ‘Del’ deletes an unprotected device. NANO-6060 User’s Manual 4-22...
Load Setup Defaults Equal to F9. Load standard default values. Discard Changes Load the original value of this boot time. Not the default Setup value. Save Changes Save all changes of all menus, but do not reset system. NANO-6060 User’s Manual 4-23...
Unlike other Single board computer, NANO-6060 supports ATX 12V 4 Pin or Power adaptor only. Therefore, there is no other setting that really needs to be set up. However, there is ATX 4 Pin Connector – J12 & DC Jack – J1 on the NANO-6060 board.
To make sure that you have a successful start with NANO-6060, it is recommended, when going with the boot-up sequence, to hit “F2” key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well.
Page 54
5 Execute the zip file to root of the bootable USB pen drive. You can get the “Shell Flash 32.efi”, ”temp.bin”, ”Update.nsh” three files. 6 Insert your USB pen drive in USB port of the NANO-6060 board and power-on. NANO-6060 User’s Manual...
Page 55
Troubleshooting 7 Boot to EFI-Shell mode then input the “fs0:” command to switch to the root of the USB pen drive. 8 Type the ”update” command to start flash BIOS processes NANO-6060 User’s Manual...
Page 56
Troubleshooting 9 When it finished all update processes, it will reboot in 5 seconds automatically NANO-6060 User’s Manual...
Page 57
Question: How to install USB 3.0 Windows 7 driver of the NANO-6060? Answer: Because of the NANO-6060 is Bay Trail platform, USB 3.0 driver need to use the other method to install USB 3.0 driver on windows 7, but windows 8 OS doesn’t.
Page 58
Following the above 4 steps, USB 3.0 can work well on Windows 7 OS. Note: Please visit our Download Center to get the Catalog, User manual, BIOS, and driver files. http://www.portwell.com.tw/support/download_center.php If you have other additional technical information or request which is not covered in NANO-6060 User’s Manual...
Page 59
Troubleshooting this manual, please fill in the technical request form as below hyperlink. http://www.portwell.com.tw/support/problem_report.php We will do our best to provide a suggestion or solution for you. Thank you. NANO-6060 User’s Manual...
Need help?
Do you have a question about the NANO-6060 and is the answer not in the manual?
Questions and answers