Download Print this page
Holman R2E-12BK-208 Installation Instructions Manual

Holman R2E-12BK-208 Installation Instructions Manual

Electronic controls conveyor toaster

Advertisement

Quick Links

These symbols are intended to alert the
user to the presence of important operating
and maintenance instructions in the manual
accompanying the appliance.
www.star-mfg.com/scripts/manuals.aspx
to obtain this units installation & operations
manual, warranty & other documents.
Using any part other than genuine Holman factory supplied parts
relieves the manufacturer of all liability.
Holman reserves the right to change specifications and product
design without notice. Such revisions do not entitle the buyer to
corresponding changes, improvements, additions or replacements
for previously purchased equipment.
Due to periodic changes in designs, methods, procedures, policies
and regulations, the specifications contained in this sheet are subject
to change without notice. While Holman Manufacturing exercises
good faith efforts to provide information that is accurate, we are
not responsible for errors or omissions in information provided
or conclusions reached as a result of using the specifications.
By using the information provided, the user assumes all risks in
connection with such use.
CAUTION
GENERAL SAFETY INFORMATION
This equipment is designed and sold for commercial use only by
personnel trained and experienced in its operation and is not sold
for consumer use in and around the home nor for use directly by
the general public in food service locations.
Before using your new equipment, read and understand all the
instructions & labels associated with the unit prior to putting it into
operation. Make sure all people associated with its use understand
the units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both
visible and concealed. This unit has been tested and carefully
packaged to insure delivery of your unit in perfect condition.
If equipment is received in damaged condition, either apparent or
concealed, a claim must be made with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until
after equipment is unpacked, a request for inspection of concealed
damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials
for inspection. The carrier will make an inspection and will supply
necessary claim forms.
Conveyor Toasters Installation Instructions
Go to:
NOTICE
Conveyor Toasters
GENERAL INSTALLATION INFORMATION
The unit was shipped fully assembled and ready to plug into a
standard outlet specified for its voltage and amp draw. If improper
electrical supply is determined, contact a qualified electrician prior
to using the unit. Removal and replacement of the power cord
and plug will void the warranty. For assistance, contact your local
authorized service agent for service or required maintenance.
Level unit using the adjustable feet under the unit (approximately
1/2" adjustment).
Before using the unit for the first time, wipe down the exterior with
a damp cloth.
Allow enough space around the toaster for adequate ventilation.
Do not operate the unit without the crumb tray properly positioned.
Overheating and poor toasting may occur. Read all labels on the
unit and follow their instructions.
MAINTENANCE AND REPAIRS
Contact the factory, a service representative or a local
service company for service or required maintenance.
Go to www.star-mfg.com/scripts/manuals.aspx to find a service
agent near you. Replacement cord sets must be purchased from
Star Manufacturing International, Inc. or our authorized agents.
Should you need any assistance regarding the operation or
maintenance of any Holman equipment; write, phone, fax or
e-mail our service department. In all correspondence mention
the model number and the serial number of your unit, along with
the voltage.
Business Hours: 8 am to 4:30 p.m. Central Standard Time
(877) 242-0270
Telephone:
(314) 781-2714
Fax:
E-mail:
Parts@star-mfg.com
Service@star-mfg.com
Warranty@star-mfg.com
Website:
www.star-mfg.com
Mailing Address: Star International Holdings Inc., Company
10 Sunnen Drive
St. Louis, MO 63143
U.S.A.
MODEL
R2E-12BK-208
Electronic Controls
2M-Z15105, Rev. - 8/23/2011

Advertisement

loading

Summary of Contents for Holman R2E-12BK-208

  • Page 1 Before using the unit for the first time, wipe down the exterior with NOTICE a damp cloth. Using any part other than genuine Holman factory supplied parts relieves the manufacturer of all liability. Allow enough space around the toaster for adequate ventilation.
  • Page 2 The Holman RCSe conveyor toaster A w i r i n g d i a g r a m i s i n c l u d e d i n t h e I n s t a l l a t i o n &...
  • Page 3 CERTAIN SURFACES ARE EXTREMELY HOT PROGRAMMING DURING OPERATION AND CARE SHOULD A. CONVEYOR SPEED (temporary setting) CAUTION BE TAKEN WHILE USING THIS UNIT. The conveyor speed is programmable with a range from 0 to 99 with 0 being the slowest and 99 being the fastest. Each menu item can START UP have independent conveyor speed settings.
  • Page 4 TABLE/COUNTER IF THE UNIT IS ON THE WARNING TABLE/COUNTER. KEEP AWAY FROM RUNNING WATER. STAR INTERNATIONAL HOLDINGS INC. COMPANY WARNING Star - Holman - Lang - Wells - Bloomfield - Toastmaster 10 Sunnen Drive, St. Louis, MO 63143 U.S.A. (314) 678-6303 www.star-mfg.com...
  • Page 5 Star Manufacturing International Inc. Service Kit 10 Sunnen Dr. Instructions St. Louis, MO 63143 Phone: (314) 781-2777 FAX: (314) 781-2714 CONVEYOR BELT REMOVAL PROCEDURES For units without Master Links 1) Turn off unit and allow to cool. 2) WARNING - DISCONNECT UNIT FROM POWER SUPPLY OR TURN OFF AT WALL BREAKER BEFORE PROCEEDING TO NEXT STEP.
  • Page 6 6) Trace that link down to the other end and unhook from the opposite side. 7) Using both hands, bring both ends together and push the link forward to disengage it from the belt. 8) Re-hook the loose ends back onto the previous link, to prevent the link from being damaged or bent.
  • Page 7 10) For heavy soiled Conveyor Belt, soak over night in hot soapy water. 11) Take this opportunity to clean and remove any loose materials the inside of the unit. Using a mild cleaner and damp cloth, carefully wipe the inside surfaces being sure NOT to clean the heater tubes.
  • Page 8 15) Bring the two ends together and thread them through the middle section of the opposite end of the belt, using both hands. 16) Re-hook the two ends of the Conveyor, once again completing the Conveyor Belt system. 17) Examine the oven to assure proper installation, once satisfi...
  • Page 9 ATTENTION! READ BEFORE USING THE TOASTER This toaster was shipped in its current state to meet your program deadline. But there are changes to be made before starting to use it. The crumb tray shipped with this unit is the wrong one. Using it will cause the croissants to get stuck and burn. Remove the crumb tray and disguard it. A new crumb tray will be shipped to you in a few days. The time and temperature for the food products is also wrong. You must reprogram the toast- er using the instructions below Plug in the toaster...
  • Page 10 CROIS Press the CROIS (croissant) button. The display will read CROIS. CROIS Press the UP and DOWN arrow buttons at the same time and hold for 3 seconds...
  • Page 11 CRS10 The display will read CRS10. The FRONT HEAT indicator will light. CRS 8 Press the DOWN arrow button twice to change the temperature to 8...
  • Page 12 CRS10 Press the CROIS button. The display will read CRS10 The BACK/BOTTOM HEAT indicator will light CRS 8 Press the DOWN arrow button twice to change the temperature to 8...
  • Page 13 CRS70 Press the CROIS button. The display will read CROIS70 The CONVEYOR SPEED indicator will light CRS45 10. Press the DOWN arrow button until the display reads CRS45.
  • Page 14 CROIS 11. Press the CROIS button. The display will read CROIS and the toaster is ready for use. 12. Start with step 3 again but substitute the CROIS button with the MUFFIN button. Change the settings to: FRONT HEAT BACK/BOTTOM HEAT CONVEYOR SPEED 13. Start with step 3 again but substitute the CROIS button with the PASTRY button. Change the settings to: FRONT HEAT BACK/BOTTOM HEAT CONVEYOR SPEED...
  • Page 15 15 41 Certain Models or Q2-3KL-KIT SOME ITEMS ARE INCLUDED FOR ILLUSTRATIVE PURPOSES ONLY AND IN CERTAIN INSTANCES MAY NOT BE AVAILABLE This drawing contains information confidential to Star Manufacturing International, Inc. No reproduction or disclosure of its contents is permitted. ®...
  • Page 16: Parts List

    PARTS LIST December 29, 2011, Rev. D Models: Q2-500-120V, Q2E-500-120V, Q2-500-CUL20, Q2-600H-CE, Q2-600H-UK, Q2-600HF-208, Q2-600H-208/220/240V, Q2-600HS-208, Q2E-600H-208/240V, Q2-800-208/220/240V, Q2-800-240UK, Q2-800-230CE, Q2E-800-208/240V, CONVEYOR TOASTERS Q2-1200B-208/240V, R2-12BSZ-208/240V, R2--1200-208/240V, R2-600HJ-208/240V, R2-800-208V Part No. Description Application HC-120258 ENCLOSURE ASSY - QCS-2 Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-208/240V, R2- HB-120270 TOP BAFFLE ASSY QCS-2 LOW 1200B-208/240V, R2-600HJ-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-...
  • Page 17 ELEMENT GUIDE PLATE 208/240V, Q2-600H-CE, Q2-600H-UK, R2-800, R2E-800 HC-Z10439 ELEMENT GUIDE PLATE 1200 Q2-1200B-208/240V HC-Z10442 ELEMENT GUIDE PLATE SERP R2-12BSZ-208/240V, R2-1200B-208/240V, R2E-12BK-208 R2E-800-208V Q2E-300H-120, Q2E-500-120V, Q2E-500CUL20, Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-1200B-208/240V, R2-12BSZ-208/240V, 2E-Z10406 TERMINAL BLOCK 4 POS. R2-1200B-208/240V, Q2-500-120V, Q2-500-CUL20, Q2E-500-120V, Q2E-...
  • Page 18 Q2E-600H-208V, Q2E-500-120V, Q2E-500CUL20 2M-Z13358 LABEL - CONTROL Q2E-600HW Q2E-600HW 2M-Z13864 LABEL - CONTROL PANEL R2E R2E-500-120V, R2E-800-208V 2M-Z14858 LABEL - CONTROL R2E-12BK R2E-12BK-208/240 KNOB, CNTRL Q SERIES, Q2-600H-208/220/240V, Q2-800-208/220/240V, Q2-500-120V, Q2-500- 2R-200768 SPEED CUL20, Q2-600H-CE, Q2-600H-UK KNOB, POWERSAVER Q Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208V, Q2-500-...
  • Page 19 2K-200463 BUSHING CORD HEYCO 1247 Q2-600H-208/220/240V, Q2-800-208/220/240V, R2-600HJ-208V 2K-200465 BUSHING CORD HEYCO12/3 BL Q2-1200B-208/240V, R2-12BSZ-208/240V, R2-1200B-208/240V Q2E-600H-208/240V, Q2E-800-208/240V, Q2E-500-120V, R2-800-208V, 2K-Y2968 BUSHING - HEYCO 7W-2 R2E-500-120V, R2E-12BK-208 2P-200267 WIRE BRUSH R2-1200B-208V D9-GR0216 POWER CORD ASSY-UK Q2-800-240UK 2E-200375 CORD SET, 14/3 120V EZ10...
  • Page 21 FRONT ELE. CONTROL SIDE REAR ELE. BOTTOM HEAT BLACK WHITE 7 BLACK WHITE 120V 240V 240V 120V WHITE F1 M1 3 BLACK QCSe BLACK WHITE SOME ITEMS ARE INCLUDED FOR ILLUSTRATIVE PURPOSES ONLY AND IN CERTAIN INSTANCES MAY NOT BE AVAILABLE R2E-12BK WIRING DIAGRAM SK2512 REV.- 5-18-11...