Nikon D200 Repair Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Digital Camera
  5. D200
  6. Repair manual

Nikon D200 Repair Manual

Hide thumbs Also See for D200:
Table of Contents

Advertisement

Quick Links

Recycled paper
再生紙を使用しています
Printed in Japan November 2005
REPAIR MANUAL
VBA13001-R.3677.A
作成承認印
VBA13001
Copyrigh ｃ 2005 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
INC
配布許可印
サービス
計画課
Ｍ

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nikon D200

Summary of Contents for Nikon D200

  • Page 1 VBA13001-R.3677.A 作成承認印 配布許可印 サービス 計画課 Ｍ VBA13001 REPAIR MANUAL Copyrigh ｃ 2005 by Nikon Corporation. All Rights Reserved. Recycled paper 無断転載を禁ず !! 再生紙を使用しています Printed in Japan November 2005...

  • Page 2: Specifications

    VBA13001-R.3677..A Specifications Type Single-lens reflex digital camera with interchangeable lenses Effective pixels 10.2 million LBCAST image sensor 23.6× 15.8 mm; total pixels: 10.92 million Image size (pixels) 3872× 2592 (L), 2896× 1944 (M), 1936× 1296 (S) Lens mount Nikon F mount (with AF coupling and AF contacts) Compatible lenses Type G or D AF Nikkor All functions supported (except IX Nikkor)
  • Page 3 VBA13001-R.3677..A Focus-area selection Normal frame (11 focus areas): Single area or group can be selected from 11 focus areas Wide frame (7 focus areas): Single area can be selected from 7 focus areas Lens servo Instant single-servo AF (S); continuous-servo AF (C); manual (M); predictive focus tracking automatically activated according to subject status in continuous-servo AF (C) Autofocus TTL phase detection by Nikon Multi-CAM2000 autofocus module...
  • Page 4 VBA13001-R.3677..A Flash X-contact only; flash synchronization at up to 1/250 s Sync contact Flash control TTL flash control by 1005-segment RGB sensor: - i-TTL balanced fill-flash for digital SLR (built in Speedlight or SB-800/SB-600 with other meterings than spot metering) - Standard i-TTL balanced fill-flash for digital SLR (built in Speedlight or SB-800/SB-600 with spot metering) 　(Can be set on speedlight when SB-800/SB-600 is used)　...

  • Page 5: Operating Environment

    - One rechargeable Nikon EN-EL3e lithium-ion battery Power source Voltage 7.4V DC［Quick charger MH-18a］is used - MB-D200 multi-power battery pack (available separately) with one or two rechargeable Nikon EN-EL3e lithium-ion batteries or six (LR6 (AA) alkaline, ZR6 nickel-manganese, or HR6 nickel-metal-hydride) batteries...
  • Page 6 　・Do NOT mix up lead-free solder with traditional solder. Caution: When "Separation of Front body from Rear body", "Disassembly of CCD/FPC unit" and "Disassembly of Bayonet" are performed, be sure to carry out "RESET AF-DEFOCUS COMPENSATION" of the D200 adjustment software after assembly. - Ｄ1 ･...
  • Page 7 VBA13001-R.3677.A Disassembly 1. Separate Front and Rear bodies External rubber ･ Remove the external rubbers (#B63,#B60,#B61,and #B447). #B61 #B447 #B63 #B60 Bottom cover ･ Remove the battery lid (by tilting and pulling it). ･ Take out two screws (#1556), six screws (#1549) and two screws (#1547). #1547 ･...
  • Page 8 VBA13001-R.3677.A Rear cover ・ Take out two screws (#1552), two screws (#1547) and one screw (#1549). ・ Remove the rear cover. #1549 #1547×2 #1552×2 ・ Remove the three TFT-PCB connection FPCs from the connector. - Ｄ3 ･...
  • Page 9 VBA13001-R.3677.A WARNING 警告 � Take extra care not to get an electric shock when 内部に高電圧部あり。カバーを外す時は感電に注意すること。 detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, b e sure to discharge the main condenser according to the instructions of repair manuals . サーの放電を必ず行うこと。 　 I/F cover ・...
  • Page 10 VBA13001-R.3677.A Disassemble Rear Cover #467 #1538 × 2 #RP00007 #985 #481 #469 #474 #986 #468 #455 #476 #465 #426 #924 #1511 × 2 #1630 #1631 #478 #477 #456 #479 #472 #1020 #473 #1511 × 2 #470 #430 #480 #422 #1512 × 3 - Ｄ5 ･...
  • Page 11 VBA13001-R.3677.A #431 #433 #434 × 2 #435 × 2 #488 #1057 #1626 #489 #1629 #487 #1633 #432 #492 #484 #483 × 2 #485 #1546 #440 #491 #1571 #486 #987 #1632 × 2 #427 #1518 × 2 #921 #441 #425 #922 #445 #443 #424...
  • Page 12 VBA13001-R.3677.A DG shield plate Soldering bridge DG-PCB unit ・ Remove the tape (#926). ・ Remove five FPCs from the connector. ・ Remove the two harnesses from the connector. ・ Unsolder the four wires. ・ Remove the DG-PCB unit (#B1017). #926 #926 #B1017 DG-PCB unit Harness...
  • Page 13 VBA13001-R.3677.A CCD/FPC unit CF card holder ・ Take out three screws (#1639) and remove the CCD/FPC unit (#B2032). ・ Take out three screws (#1543) and remove the CF card holder (#1018). #1639×3 サービス 計画課 Ｍ - Ｄ8 ･...
  • Page 14 VBA13001-R.3677.A Power drive PCB ・ Unsolder six wires. ・ Remove the harness of the back of the power drive PCB. ・ Take out two screws (#1541) and remove the power drive PCB. #1541 Brown: Main-PCB Yellow: Main-PCB Black: Charge motor Red: Charge motor Blue:AF motor #1541...
  • Page 15 VBA13001-R.3677.A DC/DC PCB unit ・ Unsolder six wires. ・ Take out four screws (#1541) of the DC/DC-PCB (#1047). ・ Remove the harness (#1074) from the DC/DC-PCB (#1047). ・ Remove the harness (#1075) from the DC/DC-PCB (#1047) and from the connector of the power drive PCB (#1002).
  • Page 16 VBA13001-R.3677.A Top cover ・ Remove the tape (#930). ・ Unsolder four wires. Tape (#930) Red: SB-PCB Black: SB-PCB Yellow: SB-PCB Brown: SB-PCB ・ Remove the cover (#850). Take out the screw (#1622) , and remove the diopter adjustment knob unit (#852, #857, #851). Pop this up.
  • Page 17 VBA13001-R.3677.A Disassembly of Top cover unit SB upper case ・ Push the pop-up lever A-part of the top cover unit, and lift the built-in SB. ・ Take out two screws (#1623). (Fig.1) ・ Fold down #301 of the SB lower case on the top cover. Then while holding the hooks of the SB upper case from both sides by hand, release them from the two holes by sliding/tilting, then remove #301.
  • Page 18 VBA13001-R.3677.A Removal of Top cover FPC / Wires / SB-PCB ・ Unsolder the three metering mode FPC lead wires. △(Addition） ・ Unsolder the accessory shoe contact at four locations. Metering mode FPC lead wire Red×1, Brown×1, Black×1 Red, Brown, Black △(Revice）...
  • Page 19 VBA13001-R.3677.A SB-up spring ・ Remove the SB-up spring (#305) from the hooking part. ・ Take out the screw (#1601) and remove the SB-up spring (#305). #305 #305 #1601 Hooking part SB lower case unit ・ Pull each wire from the holes. ・...
  • Page 20 VBA13001-R.3677.A M/DFPC unit ・ Remove the FPC soldering bridges of #1025 and #1026. ・ Take out the screw (#1569). ・ Detach #1025 from the bosses. ・ Unsolder the lead wire (#1094). ・ Remove the solder of the lead wire (#1094). △...
  • Page 21 VBA13001-R.3677.A Top cover FPC unit ・ Remove the soldering bridges . ・ Unsolder the SUB dial command unit (B725) . ・ Take out two screws (#1544). ・ Remove the SUB command dial unit (B725). ・ Unsolder the MAIN command dial unit (B726) . ・...
  • Page 22 VBA13001-R.3677.A Release button / Other small parts #732 #733 #734 #742 #743 #701 #B43 #787 #730 #911 #1659 #RP5 #966 #1557×2 #1604 #1652 #748×2 #749 #1608×2 - Ｄ17 ･...
  • Page 23 VBA13001-R.3677.A Outer LCD window / Shoe mold unit / Accessory shoe / Other small parts #502 #501 #1026 #516 #503 #318 #1640×2 #316 #504 #507 #1533 #B317 #512 #701 #511 #324 #B735 #327 #323 #1605 #1565 #765×2 #766×2 #731 #1540×2 #1560 #753 #747...
  • Page 24 VBA13001-R.3677.A Main PCB unit ・ Unsolder thirteen wires. ・ Remove five FPCs from the connector. ・ Take out three screws (#1616) and remove the main PCB unit (#B1001). Black: Charge Brown: Charge Red: Charge Purple: Battery contact Blue：FG-ID ・ Unsolder the two wires of the back of the main PCB unit (#1001). ・...
  • Page 25 VBA13001-R.3677.A Separation of Front body from Rear body ・ Take out two screws (#1529), one screw (#67), two screws (#1531), one screw (#1525) and five screws (#1575). ・ Release the AF motor wires from the bosses, and while pulling them slowly from the holes of the rear body, remove the front body.
  • Page 26 VBA13001-R.3677.A Grip unit ・ Remove the grip (#57) with the screw (#1515) and two screws (#1509). #826 #952 #952 #1517 #1515 #828 #1559 #829 #1509 #1509 #439 #1541 #769 - Ｄ21 ･...

  • Page 27: Front Body

    VBA13001-R.3677.A 2. Front body Metering FPC unit Prism box unit (with prism and eyepiece) ・ Remove the metering FPC from the connector of the SI- FPC (#1005). ・ Take out three screws (#883), and remove the metering FPC unit (#B10006). ・...
  • Page 28 VBA13001-R.3677.A Eyepiece lens-barrel unit　 Inner LCD unit ・ Take out two screws (#1619), and remove the eyepiece lens-barrel unit. ・ Remove the finder-display FPC (#1004) from the connector of the SI-FPC. ・ Take out two screws (#1618), and remove the finder-display LCD unit. #847 #B846 #844...
  • Page 29 VBA13001-R.3677.A Penta unit #B1005 #954 #953 #1619x2 #955 #832 #840 #904 #837 #876 #875x2 #833 #839 #1055 #838x2 #901 #873x2 #877A～B #902 #834 #872x2 #874x2 #877C×2 #836A～C #835 - Ｄ24 ･...
  • Page 30 VBA13001-R.3677.A AF-PCB unit ・ Take out the screw (#1507). ・ Remove the AF-PCB FPC from the connector. ・ Take out the three screws (#295) with the Hexagonal wrench, and remove the AF-PCB unit (#B1007). ・ Three springs (#293) come off. - Ｄ25 ･...
  • Page 31 VBA13001-R.3677.A 10-pin plug 10-pin FPC unit ・ Unsolder six wires. ・ Remove the soldering bridge at nine locations of the 10-pin terminal (#41) and 10-pin FPC. ・ Remove the soldering bridges at eight locations of the 10-pin FPC (#1010) and the lens contact FPC. ・...
  • Page 32 VBA13001-R.3677.A Bayonet unit Aperture coupling-ring unit SCM-change lever unit Front cover unit ・ Remove the SCM screw cover plate (both-sided adhesive tape: #389). Take out the screw (#1551) and remove the SCM-change lever (#383). ・ Take out four screws (#1621) and the screw (#1620), and remove the bayonet (#401) and the bayonet spring (#402).
  • Page 33 VBA13001-R.3677.A Lens release SW Lens release PCB unit Vertical-shooting lever SCM-change PCB #66×3 #1516 #381 #1568 Black Brown #1527 #979 #378 #1034 #380 #379 #978 #377 △(Revice） #382 Blue #385 #356 #1563 #1539×2 #386 #977 #1116 #357 #359 #384 #376 #1654x2 #372 #371...
  • Page 34 VBA13001-R.3677.A AF drive-PCB unit Horizontal-shooting lever unit #1636 #343x2 #344x2 サービス - Ｄ29 ･...
  • Page 35 VBA13001-R.3677.A Mirror BOX unit I-base plate unit 45°-support base plate Mirror unit ・ Remove the FPC of the I-base plate unit (#B71) from the connector of #B1009. Be careful NOT to lose the washers (#236A - E). #233 #1523x2 #231 #1525 #232 B10201...
  • Page 36 VBA13001-R.3677.A #B1009 B1008 #1507x2 Soldering bridge #1510x4 #235 #234 #35x2 Soldering bridge #B1024 #412×2 #B411 #1652x2 #1525 #934x2 #36x2 #33x2 - Ｄ31 ･...
  • Page 37 VBA13001-R.3677.A 2. Rear body DC/DC-PCB shield plate #1537×2 #687 ・ Take out two screws (#1537) and the screw (#1539). ・ Remove the DC/DC-PCB shield plate (#687). #1539 Main condenser/DI-PCB ・ Take out the screw (#1564), and remove the DI- PCB (#1029). ・...
  • Page 38 VBA13001-R.3677.A #397 ・ Remove the IF GND steel plate (#397). AF-assist lamp #1368 ・ Take out the screw (#1368). ・ Remove the AF-assist lamp (#B326). #B326 U/D base plate ・ Take out the screw (#1572). ・ Take out three screws (#1573). #B16620 #1573×3 #1572...
  • Page 39 VBA13001-R.3677.A Shutter unit ・ Remove the retaining tape (#956). ・ Take out three screws (#1541). ・ Remove the GND steel plate (#398). ・ Remove the shutter unit (#31). #398 #956 #1541×3 Option pack FPC ・ Take out four screws (#1542). ・...
  • Page 40 VBA13001-R.3677.A Battery contact spring #B823 #1567 ・Take out the screw (#1567), and remove #B822. ・Take out the screw (#1567), and remove #B823. ・Take out the screw (#1540), and remove #B824. #1540 #B824 #1567 #B822 Rear body small parts #1641×2 #915×2 #682×2 #889×2 #959...
  • Page 41 VBA13001-R.3677.A Rear body small parts ・Attach two #682 on the body and fix them with two screws (#1641). ・Attach two #889 to cover the screw holes without fail. ・Attach the 2 pieces of the both-sided adhesive tape (#915). #1641×2 #915×2 Position for attaching #915 #682×2 　　...
  • Page 42 VBA13001-R.3677.A Both-sided adhesive tape (to collect dust around aperture) ・Attach 4 pieces of #244 on the body. ※ Attach the tape from the inside without any slackness, then fold it down to conform to the shape of the corner. #244 Attach the tape without any gap at the corner.
  • Page 43 VBA13001-R.3677.A O p t i o n a l p a c k ・Attach the both-sided adhesive tape (#927) on #1027. Position for attaching the both-sided adhesive tape ※ Do NOT cover the positioning hole of #1027. ・Attach #1027 on #825. ・Attach #994 on #1027.
  • Page 44 VBA13001-R.3677.A Shutter unit Position for attaching the both-sided adhesive tape ・Attach the both-sided adhesive tape (#245 and #246) on #31 to collect dust. ※ When attaching, be careful NOT to give pressure on the shutter side. #246 #245 Installment of Shutter unit ・Peel off the four pieces of the backing paper (#244) that were attached on the rear body.
  • Page 45 VBA13001-R.3677.A U/D PCB unit ・Assemble the U/D PCB unit (#B16620) in the body. ① The shutter must be in state of charging (being about to be released). 　(Check this by the shutter curtain.) ② The charging SW must be at the initial position. 　(All the brushes are on the gold pattern.) ③...
  • Page 46 VBA13001-R.3677.A AF-assist lamp ・Hook the shutter FPC to the boss. 　(See below) ・Put the AF-assist lamp (#B326), and tighten the screw (#1638). FPC hooking position #1638 #B326 Lamp positioning pinhole I/F board unit Positioning boss×4 #397 ・Fit the I/F GND steel plate (#397) in the positioning bosses.
  • Page 47 VBA13001-R.3677.A Main condenser/DI-PCB ・Assemble the main condenser (#1067) in the body, and attach two pieces of the both-sided adhesive tape (#915). When the main condenser is ※ Refer to the below for the lead direction of the mounted, the connector must be main condenser.
  • Page 48 VBA13001-R.3677.A DC/DC shield plate ・Attach the DC/DC-PCB insulating sheet (#697) on the DC/DC-PCB shield plate (#687). #687 Reference position #697 ・Assemble the DC/DC-PCB shield plate (#687) in the body. 　　 （Put the bending portions of #687 into the square holes of the body.) ・Tighten two screws (#1537).
  • Page 49 VBA13001-R.3677.A Assembly / Adjustment 1. Front body Oil barrier: OS-30MF ・ Position #B411 upwards, and fix it with the screw (#1525). ・ Attach #B1024 by aligning with the positioning boss of #26. ・ Solder #B411 and #B1008 at eight locations. ・...
  • Page 50 VBA13001-R.3677.A Installment of Mg U-groove lever ・ When mount each Mg, arrange clearances between the U-groove lever and the iron core. Check the clearances when the iron core of Mg is attached. Iron core of Mg Mirror-drive Mg (#131) Ratchet gear Locking lever 0.2 ～...
  • Page 51 VBA13001-R.3677.A ・ Position #B211 in the direction of the arrow, and fix it with three screws (#1525). Grease: LEN317A #233 #1523x2 #231 #1525 × 3 #232 B10201 #229 #214 #343 #222 #10201 Direction for position #B10212 #242 #1568 #210 #B211 #236A~Exn #960 #B71...
  • Page 52 VBA13001-R.3677.A AF drive unit Horizontal-shooting lever unit ・ Fix the AF drive-PCB unit (#328) with two screws (#1636). 　Be careful NOT to pinch the AFFPC. ・ While holding the pedestal of the horizontal-shooting lever unit (#B355), turn the lever unit clockwise to apply compression to the spring.
  • Page 53 VBA13001-R.3677.A Lens release SW Lens release unit Vertical lever SCM-change PCB Grease: AX-115 Grease: G-92KA Grease: G-92KA Apply to the front, back, and inner surface of the hole. #66×3 #1516 #381 #1568 Black Brown #979 #1527 #378 #1034 #380 #978 #377 #379 #385...
  • Page 54 VBA13001-R.3677.A Front cover unit Aperture coupling-ring unit Drysurf: AX-115 Bayonet ・ Assemble the aperture coupling-ring (#RP1) into the apron (#22), and attach the spring (#406) and roller (#407). Then mount this assembled unit on the front body by turning slightly clockwise, and fi x it with two screws (#1514) and two screws (#66).
  • Page 55 VBA13001-R.3677.A ② Adjust the height of the AF coupling shaft (#342) by using the screw (#359) to "1.7±0.2 mm". ③ After the adjustment, fix the screw (#359) with Screwlock. #383 #359 Apply after the adjustment Adhesive: Screwlock ・ Measure the height of the aperture lever by using the tool (J18004). Standard：3.4±...
  • Page 56 VBA13001-R.3677.A Angle adjustment of Main mirror and sub-mirror ・Main mirror 45° adjustment Caution: ・Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. ① Check for the right-left deviation. In case the deviation is out of standard, loose three screws (#1523) and make an adjustment by moving the main mirror shaft PCB (#B10212).
  • Page 57 VBA13001-R.3677.A 10-pin plug 10-pin FPC unit ・Position the 10-pin plug (#41) so that the V-groove comes in the lower right-hand corner (viewed from the front), then fit it in the holes of the back side of the 10-pin FPC (#1010), and assemble them into #26. ・...
  • Page 58 VBA13001-R.3677.A AF CCD FPC unit ・ Assemble the adjustment springs (#293) in the bottom of the mirror BOX unit (#B211). ・ Attach the AF CCD FPC unit (#B1007) with three Hexagonal-Key screws (#295). Then, turn lightly the screws all the way in, and then back them out two-and-half turns.
  • Page 59 VBA13001-R.3677.A Penta unit Prism box unit ・ Press #8 into #832. ・ Attach #1055, #833, and two #872 by positioning them. ・ If a gap is found in #1055, replace #877A by #877B. ・ Taking careful of up/down/front/back direction, assemble #1055 and #833.
  • Page 60 VBA13001-R.3677.A Eyepiece lens-barrel unit　 #845 Adhesive: Super X Adhesive: Super X #841 #847 #841 Grease: AX-115 #B846 #847 #B846 #844 #1539 #848 #849 #841 #856 Connect the finder-display #853 FPC (#1004) to SI-FPC #845 #854 (#1005). #1539 #842 #858 #1619x2 #1005 Align the grooves of #848 and #853.
  • Page 61 VBA13001-R.3677.A ・ Fix the metering adjusting plate (#B882) with three screws (#1617). ・ Fix the metering FPC unit (#B1006) and three springs (#884) temporarily with three screws (#883). ・ Make a mountain fold of FPC, and hook 　-part to the SI-FPC (#1005), while -part to the connector.
  • Page 62 VBA13001-R.3677.A ③ While passing the two lead wires of the AF motor (#B26) into the hole of the rear body, assmeble the front body (by taking care NOT to pinch the wires but Charge lever Grease: to pull them.) G-92KA ④...
  • Page 63 ② Turn the index ring in the direction of the arrow, and shift the position by "0.17 mm" from 0 that was set in ① . (This is "0"-position of D200.) ③　Measure the body back based on "0" reference position of the index ring.
  • Page 64 VBA13001-R.3677.A Grip unit ・ Fix the grip (#57) with the screw (#1515) and two screws (#1509). #826 #952 #952 #1517 #1515 #828 #1559 #829 #1509 #1509 #439 #1541 #769 - Ａ24 ･...
  • Page 65 VBA13001-R.3677.A ・ Solder two wires on the back side of the main PCB unit (#1001). ・ Connect the main connection-FPC (#1035) to the connector of the back side of (#1001). Back side of Main PCB (#1001) Yellow: Power drive PCB ・...
  • Page 66 VBA13001-R.3677.A AF motor wire arrangement ・ Arrange the AF motor wires by placing them properly among bosses at four locations. ・ Put the power drive-PCB (#1002) into the rear body groove, and fi x it with two screws (#1541). ・ Solder six wires. ・...
  • Page 67 VBA13001-R.3677.A ・ Connect the harness (#1075) to the DC/DC PCB (#1047) and the connector of the power drive PCB (#1002). ・ Fix the DC/DC PCB (#1047) with four screws (#1541). ・ Solder six wires. Black: Battery contact Red: Battery contact Yellow: SBDI-PCB Brown: SBDI-PCB Black:IF-PCB...
  • Page 68 Set the camera AF to manual, and the focus ring to "0.7 m" by rotating it. ⑦　Start up the inspection and adjustment software for D200 (J18397), and select "INSPECTION AND ADJUSTMENT FOR AECCD POSITION" then "Set Camera for AE CCD POSITION".
  • Page 69 VBA13001-R.3677.A Outer LCD window / Shoe mold unit / Accessory shoe / Other small parts #502 Apply the grease to the inner surface. Grease: G-92KA #501 #1026 #516 #503 #318 #1640×2 #316 #504 #507 #1533 #B317 #512 #701 #511 Adhesive： C-8008B Align the four corners of two sponges (#766) #324...
  • Page 70 VBA13001-R.3677.A Release button / Other small parts Apply to shaft. #732 Grease: G-92KA Apply to the overall back side. Apply overall. #733 Oil barrier: OS-30MF #734 #742 #743 Apply overall. Grease： G-92KA Direction for assembling. #701 Apply to about two screw threads.
  • Page 71 VBA13001-R.3677.A #1544 × 2 B725 はんだ B726 #1571 - Ａ31 ･...
  • Page 72 VBA13001-R.3677.A Ｍ／ＤＦＰＣ部組 Ｍ／ＤＦＰＣ部組 ・B502,B504( 三つ葉釦部組 ) を取り付ける。 ・FPC を持ち上げビス #1572 を締める。 ・#1094 シンクロターミナルコードのはんだ付けをする。※ △( 追加） ・#1025 をボスに差し込む。 ・ビス #1569 を締める。 ・#1025、#1026 の FPC はんだブリッジをはんだ付けをする。 三つ葉釦部組 #1569 #1569 はんだ はんだ ブリッジ #1026 #1026 #1026 はんだ箇所 ※ △( 追加） シンクロターミナ #1025 ビス #1572 ル部のはんだ付け...
  • Page 73 VBA13001-R.3677.A SB lower case unit Dipping Grease: AX-115 ・ Assemble #796, #322, and #325. #796×2 △(Revise） #796 #325 #322 #796 ・ Insert the collar (#308). ・ Insert the rotation axes (#306 and #307). ・ Mount the SB lower case unit (#B302) on the top cover. ・...
  • Page 74 VBA13001-R.3677.A Installment of Top cover FPC / Wires / SB-PCB ・ Tighten the screw (#1541). ・ Tighten the screw (#1535). ・ Tighten the screw (#1511). ・ Attach the FPC of the SB-PCB（#B1013). ・ Tighten the screw (#1601). ・ Solder seven lead wires of the SB-PCB. #1511 #1535 #B1013...
  • Page 75 VBA13001-R.3677.A Assembly of Top cover unit SB lock cover Oil barrier: OS-30MF #917C #310 #309 #312 ・ Attach #309. ・ Attach the spring (#310). #1565 SB upper case ・ While sliding the SB lower case (#301) downwards, attach its two hooks to the holes. (Fig.1) ・...
  • Page 76 VBA13001-R.3677.A Top cover Eyepiece frame ・ Fix the eyepiece frame unit (#861, #963, and #903) with two screws (#1619). ・ Connect the top cover FPC (#1003) to the connector of the main PCB unit (#1001). #1039 - Ａ36 ･...
  • Page 77 VBA13001-R.3677.A Top cover Diopter adjustment knob ・ Fix the top cover with two screws (#1511), three screws (#1555), two screws (#1547), the two screws (#1548). ・Fix the diopter adjustment knob unit (#851, #857, and #852) with the screw (#1622). Then attach the cover (#850).　...
  • Page 78 To RS232C terminal Stabilized power supply Set value ＝ 7.4V 　0.3Ω　5.0A or AC adapter EH-6 ★ J18397 D200 inspection and adjustment software Battery tool J15423 Use [9pin-25pin] conversion connector for a ★ computer with 9-pin RS-232C terminal. RJ is not available, so use a commercial item.
  • Page 79 VBA13001-R.3677.A D200 Inspection and Adjustment Software (J18397) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. IBM PC/AT compatible...
  • Page 80 2. Paste the file (D200SOFT.EXE) in the created folder. 3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts. 4. When the decompression of file is finished, the file (D200.EXE) is created. 5. The installation is completed. - Ａ40 ･...
  • Page 81 VBA13001-R.3677.A <Start-up of Program> 1. Double-click the file (D200.EXE), then Inspection and adjustment program for D200 starts. 2. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen. 　However, this is not properly viewed in the English OS.
  • Page 82 SB. (ref. adjustment software for details) AF inspection and adjustment Note: When using the adjustment software for the first time, prepare 3 cameras of D200 and measure by "WRITING OF AF ADJ. LENS OFFSET VALUE" on the main menu.　 ①　AF accuracy inspection and adjustment (Make all the following adjustments.) ②　YAW, PITCH inspection and adjustment...
  • Page 83 VBA13001-R.3677.A ・ Solder four wires that are connected from the SB-PCB. ・ Arrange four wires by positioning them towards the front body, and attach the tape (#930). SBDI-PCB: #1029 Red: SB-PCB Black: SB-PCB Yellow: SB-PCB Brown:SB-PCB Tape (#930) CF card holder ・...
  • Page 84 VBA13001-R.3677.A CCD/FPC unit ・ Position the CCD/FPC unit (#B2032) towards the direction of the arrow, and fix it with three screws (#1639). ・ Connect the harness SZ (#1073) and harness AK (#1074) to the DC/DC-PCB (#1047). ・ Solder the four shielding wires. (ref. Fig) #1639×3 Harness SZ (#1073) Harness AK (#1074)
  • Page 85 VBA13001-R.3677.A DG-PCB unit ・ Solder the GND line on G-side of the DG-PCB (#B1017). (There are "S" and "G" letters on the DG-PCB) ・ Solder each shield wire on A, B, C, and D. (ref. Fig) １１２７ ×2 Core line (coated) ＧＮＤ側...
  • Page 86 VBA13001-R.3677.A Direction for position #1510×2 - Ａ46 ･...
  • Page 87 VBA13001-R.3677.A #467 #1538 × 2 #985,#986 #RP00007 Oil barrier：OS-30MF #985 #481 #469 #474 #468 #986 Grease:G-92KA Grease:G-92KA #455 #476 Grease:G-92KA #465 Direction for position #426 #475 Crazy glue Grease:G-92KA Crazy glue #1511 × 2 #1630 #1631 #478 #477 #456 #479 #472 #1020 #473...
  • Page 88 VBA13001-R.3677.A #431 #433 #434,#435 Oil barrier：OS-30MF #434 × 2 #435 × 2 #488 #1057 #1626 Grease:G-92KA #489 Direction #1629 for position Grease:G-92KA #487 #1633 Grease:G-92KA #432 #492 #484 #483 × 2 #485 #1546 #440 #491 #440 Oil barrier：OS-30MF #1571 #486 #987 #987 Oil barrier：OS-30MF...
  • Page 89 VBA13001-R.3677.A ・ Fix the rear cover with two screws (#1547), two screws (#1552), and one screw (#1549). #1549 #1547×2 #1552×2 - Ａ49 ･...
  • Page 90 VBA13001-R.3677.A #1547 Bottom cover #1549×6 #1556 ・Replace the finder screen with the infinity focus check screen (J18394), and use the reference lens (J18010) and read the value. In case it is out of standard, increase or decrease washers (#836A, #836B, or #836C) for adjustments.
  • Page 91 VBA13001-R.3677.A External rubber ･ Attach the external rubbers (#B63, #B60, #B61, and #B447). #B61 #447 #B63 #B60 - Ａ51 ･...
  • Page 92 VBA13001-R.3677.A Necessary adjustments when parts are replaced 1. D200 adjustment software and updates Adjustments Built-in SB EEPROM AE CCD accuracy M1/8000 Aperture Battery light volume accuracy fixed positioning inspection & inspection & accuracy check level inspection & inspection & Parts to be...
  • Page 93 VBA13001-R.3677.A 2. Shooting image adjustment software and updates Writing Gr/Gb Sensi- Shading Gr/Gb com- Sensitiv- Pixel de- Pixel defect Rewriting of Initial 　　　Adjustments of fixed tivity (factory difference pensation ity ratio fect com- compensa- TFT fixed Parts to be values compensa- adj.
  • Page 94 When D200 shooting image-related and listed parts on Page A51 are replaced, be sure to make an adjustment by the shooting image adjustment software for D200 (J65084). The details of its function and how to use this software are as follows: 2.
  • Page 95 (4) Select "Search for a better drive than the one your device is using now. (Recommended)", and click "Next". (5) Click "Reference" of "Specify a location" and select the directory where the driver was copied, such as "C: ¥D200¥PTP". Then click “Next”. - Ａ55 ･...
  • Page 96 VBA13001-R.3677.A (6) Confirm that the driver is located at the right place, and click "Next". (7) Click "Finish". (8) Reboot the PC to complete the installation. - Ａ56 ･...
  • Page 97 VBA13001-R.3677.A 6. Basic usage 　(1) Perform the D200IMG.exe to start up the main screen. (ref. Fig.1) 　(2) Select ENGLISH / JAPANESE in Language to display the expected menu. (ref. Fig.2) 　(3) Click the button to start adjustments. ※ When the adjustments from 2. to 6. are made, calculate to get the "Sensitivity" and "Sensitivity ratio" reference values of (7) by using the reference body beforehand, then perform the adjustments.
  • Page 98 VBA13001-R.3677.A 7. Required equipment and conditions ※ AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not specified in the list. ★ New established tool Item Required device Setting/Remarks 1 Writing of fixed value None 2 Gr/Gb difference ・5100K color viewer　　...
  • Page 99 VBA13001-R.3677.A 8. Summary 　The summary on each adjustment is as follows: 　(1) Writing of fixed values Because the fixed value that is written in Repair Parts is blank, write the fixed value when the DG-PCB is replaced. 　(2) Gr/Gb difference compensation adjustment (G filter) Camera is faced to the light-emitting box (color viewer) of LV13 equiv.
  • Page 100 VBA13001-R.3677.A 　 　(7) Pixel defect compensation - black point When pixels of which the output level is under specified value with LV13 equiv., are detected, the coordinates of the detected pixels are rewritten as pixel defect compensation data. 　(8) Pixel defect compensation - white point Shots are taken on the dark surface.
  • Page 101 9. Procedure 9-1. Shooting image adjustment 　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D200 reference body beforehand, then perform the adjustments. (ref. 9-5.) 　● When the DG-PCB is replaced, perform all the shooting image adjustments from (1) to (6), and in other cases, perform those from (2) to (6) in this order.
  • Page 102 VBA13001-R.3677.A 　(4) Shading adjustment 　・Click "4. SHADING ADJUSTMENT" on the menu. ・Attach the tool lens (Aperture F5.6) and ND filter (ND 8× 1) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts.
  • Page 103 VBA13001-R.3677.A 9-3. Pixel defect compensation - white point 　・Check the environmental temperature (approx. 20-25°C.). 　・Provide the power for the camera via AC adapter. 　・Reset "Custom setting". 　・Set "PTP" mode by Setup menu. 　・Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera. 　・Connect the camera and PC via USB cable.
  • Page 104 In case incorrect files are included in the CF card, the details for upgrading are not displayed even after selecting "FIRMWARE VERSION" from the SETUP menu. ＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, set the MB-D200 and wire as follows: 7.8V 0.3Ω －...
  • Page 105 VBA13001-R.3677.A Black Aperture Stop Mg Mount Black Soldering 実体配線図 Soldering Black Soldering bridge bridge Soldering bridge Orange bridge WIRING Mirror-up Brown Yellow Blue △( 訂正） Black Zeabra pressure Aperture AF motor Blue welding start Mg ﾚﾝｽﾞ着脱SW受け板 Yellow Lens release SW Plate Black Green Connected...
  • Page 106 VBA13001-R.3677.A 工　具・TOOLS　 ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J15427 AE CCD 位置出し工具 ★ AE CCD positioning tool J18394 無限合致調整用スクリーン Infinity focus adjustment screen ★ J18389 反射ミラー Reflection mirror ★ J18397 カメラ部点検、調整ソフト Inspection and adjustment software for CAMERA ★...
  • Page 107 VBA13001-R.3677.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J19002 縦型焦点面検査機　LT-500S Ｊ 19110 usable Back focus collimator LT-500S Ｊ 19110 でも代用可 J18391 サブミラー５９°出し工具 Sub mirror angle adjustment tool ★ J18037 オプチカルパラレル Optical parallel J18004 絞りレバー高さ点検工具 Aperture lever positioning gauge J19004-1 インジケータ及びスタンド...
  • Page 108 VBA13001-R.3677.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others ＡＦ５０／１． ４Ｄ J18267 Lens AF50/1.4D J61185 撮像関係調整用レンズ FOR D1,D2H,D70,D70s,D50 D1 Standard lens J18191 ＮＤフィルタ－８Ｘ FOR D2H,D70,D70s,D50 ND filter 8X J18358 ＮＤフィルタ－ 4 Ｘ 1 枚使用 ND filter 4X It uses by one pieces J63070 カラービュワー...
  • Page 109 VBA13001-R.3677.A ★：新規設定工具・NEW　TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others OS-30MF ドライサ－フ　ＯＳ－３０ＭＦ DRY SURF OS-30MF(OIL BARRIER) LEN317A グリース　ＬＥＮ３１７Ａ Grease LEN317A EDB0011 ネシ゛ロック（赤）1401C Screw lock 1401C C-8008B セメダイン　８００８（黒） Cemedain 8008(BLACK) MZ-800S ドライサ－フ　ＭＺ－８００Ｓ DRY SURF MZ-800S 汎用品 アロンアルファ RJ is Not available Crazy　glue 汎用品...

Table of Contents

Save PDF