Track Editing (On Cd Changer Only); Troubleshooting - Philips CDR785/00 Service Manual

SPECIAL FEATURES
5 Press YES to confirm the position of marker A.

Track editing (on CD changer only)

CD TEXT EDITING
RECORD REC LEVEL BALANCE
TEXT
PROG TRACK EDIT
CD CD
CDR
JOG CONTROL
COMPILE CD
REC TYPE
NO
AUX
YES
ERASE FINALIZE
You can create a "track" by marking a passage of music
within one track on the current disc. This new "track" can be
used for recording or playing. The minimum track length is 4
6 Press PLAY/PAUSE 2 ; on the set to play to the stop
seconds.
position of your new "track" (The initial position of marker B
is always the position of marker A plus 4 seconds).
1 Press TRACK EDIT on the set.
starts blinking, TRACK and the current track
TRACK EDIT
7 Press YES to confirm the marked passage.
number ? are displayed. The current track number is also
blinking in the track bar.
STEP TEXT TOTAL TRACK TIME TOTAL REM REC TRACK TIME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +
COMPILE CD TRACK PROGRAM DIGITAL 12
CD RW CD RW
OPTICAL 12
SHUFFLE REPEAT ALL EDIT
ANALOG
RECORD IN PROGRESS FINALIZE ALC
2 Rotate ¡ JOG CONTROL ™ until the desired track number
• Press TRACK EDIT again to leave Track Edit mode.
is displayed.
3 Press YES to confirm the selected track.
Note: If you open the CD changer tray the edit is deleted.
The marker position A and the track time will be
displayed. The first 4 seconds of the track will be played
Clearing the track edit
continously.
1 Press NO during stop.
STEP TEXT TOTAL TRACK TIME TOTAL REM REC TRACK TIME
2 Press YES to clear the markers.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +
COMPILE CD TRACK PROG DIGITAL 12
CD RW CD RW
OPTICAL 12
SHUFFLE REPEAT ALL EDIT
ANALOG
RECORD IN PROGRESS FINALIZE ALC
4 Press PLAY/PAUSE 2 ; on the set to play to the desired
start position of your new "track" (the initial position of
marker A is always the start of the chosen track).
• To fast forward to the desired start position press 5 or 6
on the set.
• To fine tune the position press first PLAY/PAUSE 2 ; on the
set, then rotate ¡ JOG CONTROL ™.
32
The marker position B and the new "track" time will be
displayed. The first 4 seconds before marker position B
until marker position B will be played continously.
STEP TEXT TOTAL TRACK TIME TOTAL REM REC TRACK TIME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +
COMPILE CD TRACK PROG DIGITAL 12
CD RW CD RW
OPTICAL 12
SHUFFLE REPEAT ALL EDIT
ANALOG
RECORD IN PROGRESS FINALIZE ALC
is shown, A-B and the track edit time are
TRACK EDIT
displayed.
STEP TEXT TOTAL TRACK TIME TOTAL REM REC TRACK TIME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +
12
COMPILE CD TRACK PROG DIGITAL
CD RW CD RW
12
OPTICAL
SHUFFLE REPEAT ALL EDIT
ANALOG
FINALIZE ALC
RECORD IN PROGRESS
The new "track" will be stored.
CLEAR A-B ? is displayed.
The markers A-B are cleared.
WARNING LASER SAFETY
Under no circumstances should you try to repair the This unit employs a laser. Only a qualified service
set yourself as this will invalidate the guarantee. Do person should remove the cover or attempt to service
not open the set as there is a risk of electric shock. this device, due to possible eye injury.
If a fault occurs, first check the points listed, before taking
the set for repair.
If you are unable to solve a problem by following these hints,
consult your dealer or service centre.
SYMPTOM INSERT DISC indication
• possible solution: • replace or clean the disc
• insert a CD(RW), label upwards
No power • wait until the lens has cleared
• ensure that the ON/OFF button is on: the set is in standby
mode, press any key to activate it USE AUDIO CD indication
• ensure that the mains cable is plugged in correctly • insert a digital audio disc marked with "Digital audio" and
• switch the set OFF and then immediately back ON the special logo
Auto track does not work CHECK INPUT indication
• check if auto track is selected • select the correct input
• check if there are 2.7 seconds silence in between the tracks • make sure the connection cable is properly connected
(analog recording only)
• check if the source is a consumer source with the digital Will not record
output according to the IEC audio standard • clean the disc
• source is DVD player (no track information) • check if CDR(W) is an unfinalised disc
• check that the disc is recordable and replace if necessary
No sound • the disc is not an AUDIO disc (WRONG DISC)
• check the audio connections • wrong input source chosen. Input label flashing (CHECK
• if using an amplifier, try using a different source
INPUT)
• text memory full (MEMORY FULL / FINALIZE CD).
Amplifier sound is distorted When a CDRW has to be unfinalised for recording. Erase
• check that the analog output of the set is not connected to text for other disc(s) or finalise other disc(s) to obtain
the amplifier Phono input memory space
Play will not start Recording is distorted
• ensure that the label of the CD is facing up • make sure the recording level is correct
• clean the disc
• check that the disc is not defective by trying another disc 20 second pause between recordings
• see "Recording with automatic synchronized start".
Remote control does not work
• point the remote control directly at the set Set does not react
• check the batteries and replace if necessary • switch the set OFF and then immediately back ON
• select the right source first
Recorded disc does not play in other standard CD
DISC RECOVER indication player
• a power failure has occurred during recording, the CD • finalize the CDR(W)
recorder is attempting to repair the disc • insert the CDRW in a CDRW compatible player
• if DISC ERROR then appears on the display, the disc
cannot be recorded further, and cannot be finalised. But it
can still be played on the CD recorder or another CD
recorder.
• on a CDRW disc, the track being recorded is lost, but
further recording and finalisation can still be done

TROUBLESHOOTING

33