Lionel Fastrack 060 Remote Switch Owner's Manual
  1. Manuals
  2. Brands
  3. Lionel Manuals
  4. Toy
  5. Fastrack 060 Remote Switch
  6. Owner's manual

Lionel Fastrack 060 Remote Switch Owner's Manual

Lionel fastrack 060 remote switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

71-2057-250
12/04
Lionel
O60 Remote Switch
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fastrack 060 Remote Switch and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lionel Fastrack 060 Remote Switch

Summary of Contents for Lionel Fastrack 060 Remote Switch

  • Page 1 71-2057-250 12/04 Lionel O60 Remote Switch Owner’s Manual...

  • Page 2: Table Of Contents

    Connecting the controller Operating the switch in the TrainMaster Command Control environment 9-10 Servicing the lamps Limited Warranty/Lionel Service The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights reserved. Lionel ® , TrainMaster ®...

  • Page 3: Joining The Fastrack Track Sections

    Joining the FasTrack track sections asTrack track sections join together easily. With interlocking roadbed sections and Rail tab large rail tabs, the track fits together securely so you always get good electrical contact. Refer to Figure 1 to see how to join the track sections.

  • Page 4: Operating The Switch

    Operating the switch ou may operate the switch using the controller or the illuminated switch lamp on the roadbed. Refer to Figure 3. To operate the switch using the controller, power up the track, then pull the lever to the opposite position.

  • Page 5: Changing The Switch Stand Location

    Changing the switch stand location ou may choose to position the switch stand either inside or outside the loop of track. Follow these steps and refer to Figure 4 to change the location of the switch stand. 1. Remove the two screws that secure the small roadbed section to the switch and lift away the roadbed section.

  • Page 6: Routing The Controller Cable

    Routing the controller cable ou may choose to route the controller cable through the notch on either side of the roadbed. As illustrated in Figure 5, simply bend the tabs to free the cable and reroute the wire. Once the cable is in place, bend down the tabs to hold the wire in the channel. Remove the notch section of roadbed and route the wire through the notch.

  • Page 7: Mounting The Controllers

    Mounting the controllers f you have multiple switches and controllers, you may choose to snap the interlocking controller bases together and mount them to your control panel using screws. To join the controller bases, snap the bases together on a flat surface as illustrated in Figure 6. Drive screws through the holes in the controller bases to secure the controllers to your layout.

  • Page 8: Powering The Switch Through A Separate Power Supply

    Powering the switch through a separate power supply ou may choose to connect the switch to a separate power supply to operate the switch when track power is off or set to a low voltage. This is most beneficial to those operating in the conventional environment.

  • Page 9: Connecting The Controller

    Connecting the controller he four controller wires are attached to the terminals on the underside of the switch. The controller wires were attached at the factory. The connections are as follows: green wire to THRU, black wire to GND, red wire to OUT, and yellow wire to RSC LIGHTS. Operating the switch in the TrainMaster Command Control environment ou may choose to operate the switch in the TrainMaster Command Control environment...

  • Page 10: Operating The Switch In The Trainmaster Command Control Environment

    Operating the switch in the TrainMaster Command Control environment (continued) SC-2 connections The SC-2 is capable of controlling up to five remote switches at a time. Wire the switches to the terminals on the back of the SC-2 unit as illustrated in Figure 10. Do not connect your FasTrack switch to the #1 terminal on the SC-2.

  • Page 11: Servicing The Lamps

    (LEDs). The LEDs are expected to last for the life of the switch and are not user serviceable. See your authorized Lionel Service Center if your LEDs require service.

  • Page 12: Limited Warranty/Lionel Service

    Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted.

Table of Contents