Page 1
73-0202-250 5/12 C&NW 0-8-0 Steam Freight C&NW 0-8-0 Steam Freight Ready-to-Run Train Set Ready-to-Run Train Set Owner’s Manual Owner’s Manual CAUTI O N—ELECTRI C TOY NOT RECOMMENDED FOR CHI L DREN UNDER FOURTEEN YEARS OF AGE. AS WI T H ALL ELECTRI C PRODUCTS, PRECAUTI O NS SHOULD BE OBSERVED DURI N G HANDLI N G AND USE TO PREVENT ELECTRI C SHOCK.
Powering your layout with the PowerMax Transformer Maintaining and servicing your set Lubricating your locomotive Replacing your locomotive’s traction tire Replacing your locomotive’s headlamp Replacing your caboose's lamp Troubleshooting FCC Statement Lionel Limited Warranty Policy & Service 73-0202-250 Menards PA Flyer Set.indd 3 5/29/12 11:20 AM...
• Parents should periodically inspect this product for potential hazards and, if necessary, have them repaired by an authorized Lionel Service Center. In the event that such a condition exists, the transformer should not be used until it has been properly repaired.
Creating your layout Building your Lionel layout our set comes with eight curved sections, three 10" straight sections, and one terminal section of track. Figure 1 provides some examples of layouts that you can build with these track sections. You may choose to add more FasTrack track sections to create an endless number of exciting track arrangements for more fun, action, and variety.
Creating your layout Joining the FasTrack track sections asTrack track sections join together easily. With interlocking roadbed sections and large rail tabs, the track fits together securely so you always have good electrical contact. Take a look at Figure 3 to see how to join the track sections.
Creating your layout Connecting your PowerMax Transformer (continued) 4. Plug the PowerMax Transformer into your wall outlet (120 volts). As your layout expands, you may also make power connections with the stripped ends of wires, placing no more than two wires on each terminal. For best performance on large layouts, it is recommended that you use 16-gauge wire to connect your PowerMax Transformer to the track.
Figure 5. Drawbar connection Power up your locomotive with your transformer. Your locomotive is designed to operate on 7-15 volts alternating current. Virtually all Lionel and Lionel-compatible alternating-current transformers are suitable. Do not power your locomotive with direct-current (DC) transformers. Note! The locomotive was designed for use with alternating-current (AC) transformers only.
ON position. Refer to Figure 8 on page 13 for the location of the switch. The smoke generator requires the periodic addition of Lionel smoke fluid in order to function. A small bottle of smoke fluid is included with this set. Press down and unscrew the cap. Pierce the tip on the nozzle.
Running your train Coupling hen coupling your cars, at least one of the mating couplers must be open as shown at the left in Figure 6. Press down on the lock release to open the coupler, then push the cars toward each other until they lock together.
Running your train Experiencing the features of the PowerMax Transformer Refer to Figure 7 on page 12 for the location of the Transformer features listed in this section. THROTTLE Push the throttle forward to increase track power. The markings on the throttle approximate the percentage of full power.
Page 12
The green light illuminates when the PowerMax is on. Whistle/Horn Activates the whistle or horn sound effect in your Lionel locomotives. Press Throttle Controls your locomotive’s speed. Throw the WHISTLE/HORN to begin the sound; release the button to end it.
Running your train Reverse unit procedure he electronic reverse unit inside your Lionel locomotive acts like the transmission in a car. When you apply power to the track, the locomotive moves in the direction specified by the reverse unit—or it sits in neutral, awaiting another power interruption. Power interruptions are the signal that tells the reverse unit to sequence to the next operational state.
PowerMax Transformer operation Powering your layout with the PowerMax Transformer our PowerMax Plus Transformer provides a total output of 2.4 amps. Also, available voltage depends on how much load is on the output. Generally, track voltage is 0-16 volts (AC). You may momentarily approach or exceed the 2.4 amp limit of the PowerMax Plus Transformer when pulling illuminated cars, or fighting over grades with heavy loads.
We recommend that you purchase a Lionel Lubrication and Maintenance Kit (6-62927), available from your Lionel dealer. Two basic rules to keep in mind: never over-lubricate (a small amount will do) and avoid getting grease or oil on the locomotive’s wheels, contact roll- ers, or your track.
Refer to Figure 10. Remove the old traction tire from under the drive rod and slip on the replacement, Lionel part no. 6308661206. Replace the spacer, retighten the drive rod screw, and you’r e ready to pull that long freight back to the yard.
4. Pull the lamp straight up and out of the socket. Replace it with Lionel lamp no. 6308352311, available at your authorized Lionel Service Center or Lionel Service.
Be sure that the Smoke Unit switch is in the ON position. Add four to six drops of smoke fluid if you have not done so already. We invite you to visit www.lionel.com and click on the Customer Services tab to order parts and access other important service information.
Maintaining and servicing your set FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
(or copy) from an Authorized Lionel Retailer*, will at the discretion of Lionel LLC, be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a suitable replacement is not available, Lionel will offer to replace the product with a comparable model (determined by Lionel LLC), if available.
Need help?
Do you have a question about the C&NW 0-8-0 and is the answer not in the manual?
Questions and answers