Table of Contents
Advertisement
Installation and Owner's Manual
WARNING
!
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed
for the protection of children and other at-risk individuals.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fi re department.
Installation and service must be performed
by a qualifi ed installer, service agency or the
gas supplier.
4003166-06
©2013, Miles Industries Ltd.
L
EGEND
Direct Vent Gas Insert
700IN (NG) & 700IP (LPG)
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Miles Industries Ltd.
www.valorfi replaces.com
G3.5
L e a v e t h i s m a n u a l
w i t h t h e a p p l i a n c e .
R e t a i n t h i s m a n u a l
f o r f u t u r e r e f e r e n c e .
Please read this manual
BEFORE installing and
operating this appliance.
This manual contains instructions to install the
ENGINE ONLY. A front is also REQUIRED to
complete this installation. A barrier screen is pro-
vided with the front. Refer to the manual sup-
plied with the front for installation.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Ce guide est disponible en français sur demande.
Patent Pending
I N S TA L L E R
C O N S U M E R
Advertisement
Table of Contents
Related Manuals for Valor 700IN
Summary of Contents for Valor 700IN
- Page 1 G3.5 EGEND Patent Pending Direct Vent Gas Insert 700IN (NG) & 700IP (LPG) Installation and Owner’s Manual WARNING I N S TA L L E R L e a v e t h i s m a n u a l HOT GLASS WILL w i t h t h e a p p l i a n c e .
-
Page 2: Table Of Contents
Designed and Manufactured by / for Miles Industries Ltd. 190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com © Copyright Miles Industries Ltd., 2013... -
Page 3: Safety Precautions
Safety Precautions READ and UNDERSTAND all instructions carefully This unit MUST be used with a vent system as before starting the installation. FAILURE TO FOLLOW described in this installation manual. NO OTHER vent these installation instructions may result in possible fi re system or components MAY BE USED. -
Page 4: Safety And Your Fireplace
Child Safety Precautions and Recommendations, • A physical barrier is strongly recommended if there are young Parts of your Valor Fireplace become • children, or at-risk individuals in the extremely hot while in operation. house. Install an approved after- The glass viewing window •... -
Page 5: Owner's Information
For purchasing a Valor by Miles Industries. Your new EXTREMELY HOT!!! radiant gas heater is a technical appliance that must be installed by a qualifi ed dealer. Each Valor fi replace • READ the SAFETY information on pages is fully tested during the production process for your 3 and 4 of this manual BEFORE operating safety and comfort. - Page 6 OWNER’S Owner’s Information INFORMATION Cleaning To remove the window for cleaning: 1. Unhook the trim WARNING with the barrier screen. DO NOT TOUCH THE GLASS WHILE IT IS HOT! DO NOT TOUCH THE GLASS WHILE IT IS HOT! Let the fi replace cool fi rst before cleaning it. Let the fi...
- Page 7 OWNER’S Owner’s Information INFORMATION 2. Place the window in its bottom railing and push its Checks top against the fi rebox. A periodic check of the pilot and burner fl ames should 3. While you hold it, unhook the side levers from the trim be made.
- Page 8 OWNER’S Owner’s Information INFORMATION The appliance area must always be kept clear and Batteries free from combustible materials, gasoline and other WARNING fl ammable vapors and liquids. Inspect the vent terminal outdoors regularly to make DO NOT ATTEMPT TO CHANGE THE BATTER- IES WHILE THE FIREPLACE IS STILL HOT! Let sure that snow, trees, bushes, leaves, or other objects the fi...
- Page 9 OWNER’S Owner’s Information INFORMATION operating your fi replace. Lighting, Operation and Rating Information Handset and Wall Switch: Press and hold the OFF WARNING button for a second. DO NOT ATTEMPT TO TOUCH THE DATA PLATE If the fl ames are on, they go down and you hear the WHILE THE FIREPLACE IS STILL HOT! Let the valve motor wind down.
-
Page 10: Remote Control Operation
OWNER’S Remote Control Operation INFORMATION NOTE: Before using the remote control system for IMPORTANT: BEFORE YOU BEGIN, please note that the fi rst time, the receiver and the handset must be on this system, the settings of time, temperature and synchronized. - Page 11 OWNER’S Remote Control Operation INFORMATION • Press and hold (small fl ame) MODES OF OPERATION button to decrease fl ame height or • Briefl y pressing the SET button to set the appliance at pilot fl ame. changes the mode of operation in •...
- Page 12 OWNER’S Remote Control Operation INFORMATION • SETTING THE ON / OFF TEMPERATURES - Nighttime Setback T E M P Temperature Mode (Appliance must be in standby mode; pilot SETTING THE “DAYTIME” TEMPERATURE ignited) - The room temperature (sun), 23ºC / 74ºF Default Settings: TEMP is measured and compared to the...
- Page 13 OWNER’S Remote Control Operation INFORMATION SETTING THE “NIGHTTIME SETBACK” SETTING PROGRAM TIMERS TEMPERATURE • You can program two periods of time between 12:00 (moon), “ Default Settings: ” (OFF) T E M P am and 11:50 pm in each 24-hour cycle. •...
- Page 14 OWNER’S Remote Control Operation INFORMATION SETTING P1 OFF TIME SETTING P2 ON TIME • Briefl y press SET to scroll to TIMER mode • Briefl y press SET button to scroll (sun) while the time fl ashes. to TIMER (moon) while the •...
-
Page 15: Options
Conversion Kit 706EBL—Enamel Black Liner Set 700PGK—Conversion Kit to Propane Gas 707FBL—Fluted Black Liner Set 700NGK—Conversion Kit to Natural Gas 708VRL—Valor Red Brick Liner Set Hearth Gate Fuel Bed Hearth gates such as Cardinal’s VersaGates are 701RSK—Rock Set available at retail stores carrying safety products 702LSK—Log Set... -
Page 16: Lighting Instructions
OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING : If you do not follow these instructions exactly A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To save gas, turn the pilot off when not using the appliance for a prolonged period of time. -
Page 17: Installation Planning
Supply Gas licensed or trained personnel should install this appliance. Heater engine 700IN is used with natural gas. Heater engine 700IP is used with propane gas. This appliance must be electrically grounded in The supply pressure must be between the limits shown accordance with local codes, or, in the absence of local in the Ratings section above. -
Page 18: Overview
QUALIFIED Overview INSTALLER This appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of non-combustible material. DO NOT install into combustible construction. This appliance is NOT APPROVED for installation with a zero clearance kit. WARNING Chimney Terminal Cap Some materials or items, although... -
Page 19: Dimensions
QUALIFIED Dimensions INSTALLER 28-5/8” (727 mm) 21-1/4” (540 mm) Fan box: 6’ (1.8 m) Fan power cord 3” (76 mm) Optional fan 3” 3” 9” (76 mm) (76 mm) 13” (228 mm) (330 mm) 13” 4” Trim (102 mm) (102 mm) (sold separately) 10”... -
Page 20: Clearances
QUALIFIED Clearances INSTALLER WARNING Some materials or items, although safe, may discolor, shrink, warp, crack, peel, Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the fi replace. Avoid placing candles, and so on because of the heat produced by the fi... -
Page 21: Venting
QUALIFIED Venting INSTALLER Typical Vent Installation See the Approved Venting Accessories list on page 39 of this manual. NOTE: Flexible co-linear vent pipes may only be installed into existing non-combustible solid-fuel burning fi replaces and chimneys. Terminal Cap Vent Location The vent terminal must be located above the roof. -
Page 22: Existing Fireplace Preparation
QUALIFIED Existing Fireplace Preparation INSTALLER A few points must be considered before inserting the Gas Line Routing 700 into an existing fi replace cavity. Generally, no Plan the routing of the gas line before proceeding. modifi cations are allowed to the existing fi replace that Utilize the existing hole for the gas line of the factory- will compromise the integrity of the existing fi... - Page 23 QUALIFIED Appliance Preparation INSTALLER Window Removal The window is held in place by a spring-loaded lever on each side. 1. To remove the window, locate the levers on each side of the window towards the top. Using your fi nger, pull the lever towards you and unhook it from the window frame bracket.
- Page 24 QUALIFIED Appliance Preparation INSTALLER Venting Installation IMPORTANT: This appliance’s venting system is room sealed and there- fore, does not require room air to be used in the combustion process. 1. Rough-in two 3” diameter vent liners into the existing chimney system from the roof.
-
Page 25: Supply Gas Installation
QUALIFIED Supply Gas Installation INSTALLER The gas supply inlet connection is a 1/2” NPT female. A The appliance must be isolated from the gas supply gas shut-off valve is supplied on the end of a stainless piping system by closing its equipment shut-off valve steel fl... - Page 26 QUALIFIED Supply Gas Installation INSTALLER 2. Install alternate elbow (not supplied). Inlet Connection The appliance is sup- plied with a fl ared elbow 6-3/8” (162 mm) connector fi tted onto the 3/8” street elbow(s) valve and a fl ex connec- (where allowed) tor supplied loose to be attached to the elbow...
-
Page 27: Ceramic Panels Installation
QUALIFIED Ceramic Panels Installation INSTALLER The following guidelines apply for all liner panels 5. Rotate the anchor up and out of the way and slide (supplied separately). the left hand side panel against the fi rebox side. Rotate the anchor back down to hold the panel. 1. -
Page 28: Ceramic Logs Installation
QUALIFIED Ceramic Panels Installation INSTALLER 11. With logs only: Install the front bricks in front of the 9. Reinstall the front brick support. burner. 10. Reinstall the rear log support (3 screws). Its rear 12. With logs only: Slide the cast iron grate in the edge rests on the rear brick support ledge. - Page 29 QUALIFIED Ceramic Logs Installation INSTALLER 2. Place the black glass piece on top of the burner and 4. Place the right front log with its left end fl at on the move it forward to rest in the grooved recess of the glass.
- Page 30 QUALIFIED Ceramic Logs Installation INSTALLER 6. Isntall the top right log. Place its wider end on the front right log’s peg and rest its narrow end in the notch on the rear log. 7. If desired, add loose embers on top of the front bricks between the legs of the grate in the shaded space.
-
Page 31: Ceramic Rocks Installation
QUALIFIED Ceramic Rocks Installation INSTALLER For ceramic logs, see previous section. Unpack the ceramic rocks very carefully to avoid damaging them. Install the rocks as shown. Please note that the position of some of the rocks identifi ed in the following instructions is critical to ensure proper performance of the appliance. - Page 32 QUALIFIED Ceramic Rocks Installation INSTALLER 5. Identify rocks number 1, 2, 3, 4 and 5. These rocks 8. Identify the rocks 7, 9, 11 and 14. These rocks have pegs that fi t in the holes on top of the rock have one hole underneath and fi...
-
Page 33: Side Shrouds Installation
QUALIFIED Ceramic Rocks Installation INSTALLER 11. Optional: Lay the twigs on the rocks. They can be IMPORTANT: The rocks of the top row (14, 11, 9 placed as suggested below or elsewhere on the and 7) overhang slightly over the burner. rocks as long as they do not block the pilot fl... -
Page 34: Window Refi Tting
QUALIFIED Window Refi tting INSTALLER 1. To facilitate the installation of the window, hook the 3. While you hold it, unhook the side levers from side spring-loaded levers to the side shrouds as the side shrouds and hook them into the window indicated so they are not in the way of the window brackets on each side. -
Page 35: Remote Control Initial Set-Up
QUALIFIED Remote Control Initial Set-up INSTALLER The receiver and the handset of the remote control 5. With a sharp object, press and hold the receiver’s system must be initially synchronized before the fi rst reset button until you hear one short and one long use. -
Page 36: Operation Check & Aeration Settings Adjustment
QUALIFIED Operation Check & Aeration Settings Adjustment INSTALLER In a few unusual installations, the fl ame picture may Operation Check be improved by adjusting the aeration. The need for Turn the fi replace fl ame up and down using the adjustment should be determined only by operating the remote control to confi... -
Page 37: Remote Control Handset Wall Holder Installation
QUALIFIED Remote Control Handset Wall Holder Installation INSTALLER The remote control kit for this fi replace comes complete with a wall-mounted holder. Alternative 2 Alternative 3 Packing Contents: This holder is not required in all installations 1 Wall Bracket A but is provided as an optional feature for 2 Screws B those customers who wish to mount the... -
Page 38: Wiring Diagram
QUALIFIED Wiring Diagram INSTALLER Optional Wall Switch Kit 1265WSK Connector Yellow Optional Fan Remote Control Battery Box Module 4 AA Batteries GV60 MAX Wiring Diagram... -
Page 39: Approved Venting Components
QUALIFIED Approved Venting Components INSTALLER Approved Direct Vent Suppliers for Valor Models 700, 739, 780, 785 and RF24DV Venting Parts Code / availability by Manufacturer Venting Parts Description 4DVC Standard Co-axial 46DVA-VC 4DT-VC TM-4VT — HSDV4658-1313 — 4DH-1313 High Wind Co-axial 46DVA-VCH —... -
Page 40: Warranty
OWNER’S Warranty INFORMATION If you have a problem with this unit, please contact your dealer or supplier immediately. Under no circumstances should you attempt to service the unit in any way by yourself. The warranties in paragraphs 1 and 2 are provided only to the fi... -
Page 41: Spare Parts
OWNER’S Spare Parts INFORMATION Part Part Code Description Code Description Number Number Exhaust slide assembly 4002287 Inlet elbow connector 4002909 Exhaust slide gasket 4001662 Air shutter slider NG 4002345 Restrictor enclosure 4002330 Air shutter cover NG 4002346 Metal strips (2) 4002329 Flashback shield LPG 3000371... - Page 42 4003230 #8 - 32 Hexagonal nut plated (2) 4001517 Liner panels—complete set Ledgestone 705LSL Enamel black 706EBL Ceramic fl uted black 707FBL Valor red brick 708VRL Top panel Ledgestone 4003193 Ceramic black 4003202 Ceramic black 4003202 Valor red brick 4003220...
- Page 43 OWNER’S Spare Parts INFORMATION 3 - 7 56 - 57 71 72 80, 80a 27 - 31 17 - 23a 33a, 33b...
-
Page 45: Miles Industries Ltd
Thank You ... For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed installer. Please fi ll in the information below. The information provided will be used for customer records only. -
Page 46: Miles Industries Ltd
Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...