Assembly - HAMPTON BAY CAMPBELL Use And Care Manual

Assembly - Hanging the Fan (continued)
3
Installing the receiver
WARNING: To reduce the risk of fire or electric shock,
remember to disconnect power. The electrical wiring must
meet all local and national electrical code requirements.
The electrical source and fan must be 110/120 volt, 60Hz.
Do not use this product in conjunction with any variable wall
control. Incorrect wire connection can damage this receiver.
CAUTION: If other fan wires are a different color, have this
unit installed by a licensed electrician.
CAUTION: Do not install in a damp location or immerse
in water (For indoor use only). Do not pull on or cut leads
shorter. Do not drop or bump the unit.
□
Position the supply wires to the left side of the slide-on
mounting bracket (A); position the fan wires to the right
side. Partially insert the remote control receiver (J) (flat side
up) until one end rests on the ball/downrod assembly (B).
B
4
Setting the code on the hand unit
NOTE: The frequencies on your receiver and hand unit have
been preset at the factory. Before installing the receiver,
make sure the dip switches on the receiver and hand unit are
set to the same frequency. The dip switches on the hand unit
are located inside the battery compartment.
NOTE: The battery will weaken with age and should be
replaced before leaking takes place as this will damage the
hand unit. Dispose of used battery properly and keep the
battery out of the reach of children.
□
Remove the battery cover by pressing firmly on the arrow
and sliding the cover off.
□
Slide the code switches to your choice of either up or down.
The factory setting is up.
Setting the code on the Receiver
□
Slide the code switches to the same position as set on the
hand unit.
□
Replace the battery cover on the hand unit.
Controller Model: MR101D or FAN38R-T190
J
A
5
Making the electrical connection
IMPORTANT: Use the plastic wire connectors (BB) supplied with
your fan. Secure the connectors with electrical tape and ensure
there are no loose strands or connections.
WARNING: Each wire nut supplied with this fan is designed to
accept up to one 12-gauge house wire and two wires from the
fan. If you have larger than 12-gauge house wiring or more
than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
NOTE: The fan comes with 54 inch lead wires for use with an
extended ball/downrod assembly. If using the 4.5 inch ball/
downrod assembly (B) provided, you can cut the lead wires to
your desired length (no shorter than 12 inches).
□
Connect the ground conductor of the 120-Volt supply (this
may be a bare wire or a wire with green colored insulation)
to the green ground lead(s) (II) of the fan using a plastic wire
connector (BB).
□
Connect the fan motor white wire (LL) to the receiver (NN)
white wire (LL) using a plastic wire connector (BB).
□
Connect the fan motor black wire (KK) to the receiver (NN)
black wire (KK) using a plastic wire connector (BB).
□
Connect the fan motor blue wire (JJ) to the receiver (NN) blue
wire (JJ) using a plastic wire connector (BB).
□
Connect the receiver (NN) red wire (OO) to the supply black
(hot) wire (KK) using a plastic wire connector (BB).
□
Connect the receiver (NN) white wire (LL) to the supply white
wire (neutral) (LL) wire using a plastic wire connector (BB).
□
After connecting the wires, spread them apart so that the
green (II) and white (LL) wires are one side of the outlet box
(MM) and the black wire (KK) is on the other side.
□
Turn the plastic wire connectors (BB) upward, and carefully
push the wiring into the outlet box (MM).
A
B
9
Please contact 1-877-527-0313 for further assistance.
MM
NN
JJ LL
KK LL
HAMPTONBAY.COM