Editing; Dubbing A Tape - Sony Handycam Vision CCD-TRV107E Service Manual

Using the built-in light
•The built-in light may turn on/off when you
use the PROGRAM AE or backlight function
while shooting in the AUTO mode (
•The built-in light may turn off when inserting
or ejecting a cassette.
•While the end search function is working, the
built-in light is turned off.
•When you use the conversion lens (optional),
the built-in light is blocked and may not
illuminate the subject properly.
Replacing the bulb
Use the Sony XB-3D halogen lamp (optional).
The supplied halogen lamp is not commercially
available. Purchase the Sony XB-3D halogen
lamp.
Remove the power source before replacing the
bulb.
(1) Remove the built-in light unit while pushing
the hole under the built-in light unit using a
wire.
(2) Turn the bulb housing anticlockwise and
detach from the built-in light unit.
(3) Replace the bulb using a dry cloth.
(4) Attach the bulb housing by turning it
clockwise, then replace the built-in light unit.
1 2
4
64
— Editing —

Dubbing a tape

Using the A/V connecting cable
Connect your camcorder to the VCR using the
A/V connecting cable supplied with your
camcorder.
You can record and edit a picture with the
connected VCR by using your camcorder as a
player.
Set DISPLAY to LCD in in the menu settings
(The default setting is set to LCD.)
If you do not make the indicators disappear, they
are recorded on tapes.
Make the indicators disappear by pressing the
following buttons:
– DISPLAY on your camcorder
– DISPLAY on the Remote Commander (CCD-
TRV107E/TRV208E/TRV408E only)
(1) Insert a blank tape (or a tape you want to
record over) into the VCR, and insert the
recorded tape into your camcorder.
(2) Set the input selector on the VCR to LINE.
Refer to the operating instructions of your
VCR for more information.
(3) Set the POWER switch to PLAYER.
(4) Play back the recorded tape on your
camcorder.
(5) Start recording on the VCR.
Refer to the operating instructions of your
VCR for more information.
S VIDEO OUT
A / V OUT
: Signal flow/
A/V connecting cable (supplied)/
66
).
•
(1)
(2)
(3)
(4)
3
NOTE
Be sure to align the tab with the
groove when inserting.
(1)
(2)
(3)
(4)
(5)
Yellow/
IN
S VIDEO
VIDEO
AUDIO
Black/
CCD-TRV107E/TRV108E/TRV208E/TRV408E
Using the built-in light
CAUTION
•When replacing the bulb, use only the Sony
XB-3D halogen lamp (optional) to reduce the
risk of fire.
•To prevent possible burn hazard, disconnect
the power source before replacing and do not
touch the bulb until the bulb becomes cool
enough to handle (for about 30 minutes or
more).
Note
To prevent the bulb from being smudged with
finger prints, handle it with a dry cloth, etc. If the
bulb is smudged, wipe it completely.
Dubbing a tape
When you have finished dubbing a
tape
Press x on both your camcorder and the VCR.
To prevent deterioration of pictures
when dubbing
Set EDIT to ON in the menu settings before
dubbing.
You can edit on VCRs that support the
following systems:
8 mm , Hi8 , Digital8 , VHS ,
S-VHS , VHSC , S-VHSC
Betamax , mini DV or DV
If your VCR is a stereo type
Connect the audio plug of the A/V connecting
cable supplied to the left (white) input jack of
your VCR.
If your VCR has an S video jack
Connect using an S video cable (optional) to
obtain optimum quality screen images.
With this connection, you do not need to connect
the yellow (video) plug of the A/V connecting
cable.
Connect an S video cable (optional) to the S video
jacks of both your camcorder and the VCR.
1-15
x
,
,
65
67