Godex GS220 Quick Start Manual

GS220

Bar Code Scanner

Quick Start Guide

220-QS Rev D
12/12

Suffix

Scan one of the following bar codes to program your scanner to add
or remove a carriage return, line feed, tab, or end of text after each
bar code.
³ 1 1 6 6 1 3
CR Suffix On
³ 1 1 6
CR Suffix Off
³ 1 1 6 6 1 2
LF Suffix On
³ 1 1 6
LF Suffix Off
³ 1 1 6 6 1 0
Tab Suffix On
³ 1 1 6
Tab Suffix Off
³ 1 1 6 6 1 4
ETX Suffix On
³ 1 1 6
ETX Suffix Off

Getting Started

Turn off the computer's power before connecting the scanner, then
power up the computer once the scanner is fully connected.

Connecting the Scanner

USB:
Keyboard Wedge:

User Configurable Prefix/Suffix

One or two prefix or suffix characters can be added and assigned for
data transmission. Use one of the codes below with a 3 code byte
sequence that represents the desired character (see
Conversion Chart, end of document) for your prefix or suffix. (To add
additional prefix/suffix characters, refer to your Single-Line
Configuration Guide.)
Scan the Enter/Exit Programming bar code to begin. Then scan
the 3 digit decimal equivalent of the ASCII character into the
6 0 3
appropriate character location with the code byte bar codes (see
Code Bytes, end of document). To save, scan the Enter/Exit
Programming bar code again.
Example: To add an asterisk (*) as a prefix, scan the bar codes:
1. Enter/Exit Programming
6 0 2
2. Configurable Prefix #1
3. Code Byte 0
4. Code Byte 4
5. Code Byte 2
6. Enter/Exit Programming
6 0 0
³ 9 9 9 9 9 9
Enter/Exit Programming
6 0 4
³ 9 0 3 6 0 0
Configurable Prefix #2
³ 9 0 4 6 0 0
Configurable Suffix #2

Reading Techniques

Recall Defaults

The following bar code resets all standard product default settings.
³ 9
Recall Defaults

Interface Selections

USB
³ 3
USB Keyboard
Keyboard Wedge
³ 5
Keyboard Wedge Emulation
Supplements
Scan one of the bar codes below to program your scanner for 2 or 5
digit bar code supplements.
ASCII
³ 1 0 1 2 0 7
2 Digit Supplements Off
³ 1 0 1 2 0 6
5 Digit Supplements Off
977 (2 Digit) Supplement Required: Turn on this feature when a 2
digit supplement is required for EAN-13 codes that begin with 977.
³ 1 0 1 3 0 4
977 Supplements Off
³ 9 0 3 5 0 0
Configurable Prefix #1

Scan Modes

When you scan Continuous Blinky Scan mode, the scanner beam
flashes and scans continuously. To enter the mode, scan below codes:
1. Enter/Exit Programming
³ 9 0 4 5 0 0
Configurable Suffix #1
3. Continuous Blinky_2
5. Enter/Exit Programming
To exit from Continuous Blinky Scan mode, scan the Recall
Defaults barcode.

Prefix

Scan one of the following bar codes to program your scanner to add
or remove a start of text character, or AIM or Nixdorf identification
characters before each bar code.
³ 1 1
STX Prefix On
³ 1 0
AIM ID Prefix On
9 9 9 9 8
1 6 4 0 0
Emulation
1 5 5 1 4 3
³ 4 1 8 3 3 4
Continuous Blinky_1
³ 1 0 1 2 1 7
2 Digit Supplements
On
1 1 8 7 0 3
Continuous Blinky_3
³ 1 0 1 2 1 6
5 Digit Supplements
On

UPC/EAN Formatting

Scan Convert UPC-A to EAN-13 and a leading zero is transmitted
before a UPC-A bar code to convert it to EAN-13.
³ 1 0 1 3 1 4
977 Supplements On
³ 1 0
Don't Convert UPC-A to
EAN-13
Scan Transmit Lead Zero on UPC-E to transmit a zero before each
UPC-E bar code.
2. Continuous Blinky_1
4. Continuous Blinky_3
³ 1 0
Don't Transmit Lead
Zero on UPC-E
6 6 1 5
³ 1 1 6 6 0 5
STX Prefix Off
7 9 1 5
³ 1 0 7 9 0 5
AIM ID Prefix Off
8 1 8 9 0 0
Continuous Blinky_2
³ 9 9 9 9 9 8
Recall Defaults
³ 1 0 7 5 1 4
Convert UPC-A to
EAN-13
7 5 0 4
³ 1 0 7 5 1 3
Transmit Lead Zero on
UPC-E
7 5 0 3