Viessmann Vitocell 100 Installation Instructions Manual

Viessmann Vitocell 100 Installation Instructions Manual

Enameled indirect-fired domestic hot water storage tank 42 and 53 usg / 160 and 200 ltr capacities
Hide thumbs Also See for Vitocell 100:

Advertisement

Installation Instructions

Vitocell 100
CHA Series
Enameled indirect-fired domestic hot water storage tank
42 and 53 USG / 160 and 200 ltr capacities
Vitocell 100
5167 514 v1.1 02/01
CAUTION
THE HEAT TRANSFER
MEDIUM MUST BE WATER
OR OTHER NON-TOXIC
FLUID HAVING A TOXICITY
RATING OR CLASS OF 1,
AS LISTED IN CLINICAL
TOXICOLOGY OF
COMMERCIAL PRODUCTS,
5TH EDITION.
THE PRESSURE OF THE
HEAT TRANSFER MEDIUM
MUST BE LIMITED TO A
MAXIMUM OF
30 PSIG BY AN APPROVED
SAFETY OR RELIEF VALVE
(SEE PAGE 2).
IMPORTANT
Read and save these instructions
for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vitocell 100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Viessmann Vitocell 100

  • Page 1: Installation Instructions

    Installation Instructions Vitocell 100 CHA Series Enameled indirect-fired domestic hot water storage tank 42 and 53 USG / 160 and 200 ltr capacities Vitocell 100 CAUTION THE HEAT TRANSFER MEDIUM MUST BE WATER OR OTHER NON-TOXIC FLUID HAVING A TOXICITY...
  • Page 2 Safety, Installation and Warranty Requirements Safety, Installation and Warranty Requirements Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the instructions listed below and details printed in these instructions can cause product/property damage, severe personal injury, and/or loss of life.
  • Page 3: Table Of Contents

    Index Page Safety Important Regulatory and Installation Requirements ..General Information About these Instructions ............Product Information .
  • Page 4: Important Regulatory And Installation Requirements

    Literature applicable to all aspects of site and advise the system the Vitocell: operator/ultimate owner where the - Technical Data Manual literature can be found. Contact - Installation Instructions Viessmann for additional copies. - Start-up/Service Instructions - Operating Instructions and User’s Information Manual...
  • Page 5: About These Instructions

    General Information/Set-up About these Instructions Take note of all symbols and notations intended to draw attention to potential hazards or important product information. These include ”WARNING”, ”CAUTION”, and ”IMPORTANT”. See below. The following symbols and flag words may be utilized in these Installation Instructions: Warnings draw your attention to the WARNING...
  • Page 6: Orientation And Dimensions

    Set-up/Connections Tank Set-up (continued) Recommended installation clearances for service access Storage capacity Rear inches Sides May be reduced if rear pipe inches connections can be reached with less clearance inches Front inches Minimum clearances to combustibles Storage capacity inches All sides Orientation and Dimensions Connections ø...
  • Page 7: Installation Of Tank Temperature Sensor And/Or Aquastat

    Where a Vitotronic 100 and a Viessmann Power/Pump Control Module WARNING are utilized to control DHW production: To ensure optimum, safe operation, 3.
  • Page 8: Verification Of Anode Connection

    DHW temperature inside the tank never exceeds 203 °F / 95 °C. 230 ºF / 110 ºC Vitocell 100 Max. supply temp. 1.Connect heating water side (primary) ..150 ºF / 65.6 ºC DHW tank temperature sensor Max.
  • Page 9: Domestic Hot Water Connections

    Connections Domestic Hot Water Connection IMPORTANT This is a simplified conceptual drawing only! Piping and necessary componentry must be field verified. Proper installation 1. Connect DHW connections using and functionality in the field is the supplied adaptors. responsibility of the heating contractor. See Installation Instruction Supplement supplied with tank.
  • Page 10: Domestic Hot Water Connection

    998 MBH and CSA Backflow preventers temperature steam rated for 200 MBH. It is Viessmann accepts no responsibility for tested under ANSI Z21.22 code for Relief damage howsoever caused and reserves the Where backflow preventers are required, a...
  • Page 11: Pressure Drop Information

    Appendix Pressure Drop Information Pressure drop on heating water side (primary circuit) 1000 42 and 53 USG / 160 and 200 ltr storage capacities ltr/h USGPM Waterflow Pressure drop on domestic hot water side (secondary circuit) 40 100 ltr/min USGPM Waterflow...
  • Page 12: Post Installation

    Service Instructions in the Service Binder. 2. Install a protective hanging case near the boiler and store the Service Binder in this location. For a listing of applicable Viessmann literature, please see Important Regulatory and Installation Requirements. Viessmann Manufacturing Company (U.S.) Inc.

This manual is also suitable for:

Vitocell 100 cha series

Table of Contents