System Parameters - Roland GAIA Synthesizer SH-01 Owner's Manual

System Parameters

Parameter Range
SYSTEM TEMPO 5–300
OCTAVE SHIFT -3–+3
TRANSPOSE SWITCH OFF, ON
TRANSPOSE VALUE -5–+6
KEYBOARD VELOCITY REAL, FIX
STANDARD,
PEDAL POLARITY
REVERSE
D BEAM SENS 1–8
LOCAL SW
OFF, ON
MASTER LEVEL 0–127
415.30–466.20
MASTER TUNE
(Hz)
PATCH REMAIN OFF, ON
Explanation
Specifies the system tempo.
This effect can be obtained only when CLOCK
SOURCE (p. 52) is set to "SYSTEM. "
Shifts the keyboard pitch range in steps of one
octave.
Turns Transpose on/off.
Specifies the range (in semitones) by which the
Transpose function will shift the keyboard.
Specifies the velocity value that is transmitted when
you play a key.
If this is set to FIX, the velocity value will be fixed.
Switches the polarity of the pedal.
Adjusts the sensitivity of the D BEAM controller.
Higher values will make the D BEAM respond more
easily.
Switches ON/OFF the connection between the
internal sound generator and the controller section
(keyboard, pitch bend/modulation lever, and pedal).
Normally, this should be left at "ON, " but if you wish
to use the SH-01 to control only external sound
modules, set it to "OFF. "
Specifies the volume of the entire GAIA SH-01.
Specifies the reference pitch of the entire GAIA
SH-01.
The setting indicates the frequency of the A4 key.
If this is on, currently sounding notes of the patch
will continue when you select another patch.
Panel operation
1. Press the [TAP TEMPO] button four or more times at
quarter-note intervals of the desired tempo.
1. Press the OCTAVE [UP/+] button.
The range will rise one octave each time you press the
button.
2. Press the OCTAVE [DOWN/-] button.
The range will fall one octave each time you press the
button.
Press the [TRANSPOSE] button.
Button lit: ON
Button unlit: OFF
1. Hold down the [TRANSPOSE] button and press the OCTAVE
[UP/+] button.
The pitch will rise by a semitone each time you press the
button.
2. Hold down the [TRANSPOSE] button and press the OCTAVE
[DOWN/-] button.
The pitch will fall by a semitone each time you press the
button.
• If you hold down the [TRANSPOSE] button and press the
OCTAVE [UP/+] button and OCTAVE [DOWN/-] button
simultaneously, the pitch will return to the normal range.
1. Hold down the [CANCEL/SHIFT] button and press the [KEY
HOLD] button.
Button lit: FIX
Button unlit: REAL
1. Hold down the [CANCEL/SHIFT] button and press the
[V-LINK] button.
2. Hold down the [PORTAMENTO] button and press the
[PRESET PATCH] button or the [USER PATCH] button.
PRESET PATCH lit: REVERSE
USER PATCH lit: STANDARD
3. Press the [CANCEL/SHIFT] button.
1. Hold down the D BEAM [EFFECTS/ASSIGN] button and
press one of the NUMBER [1]–[8] buttons.
1. Hold down the [CANCEL/SHIFT] button and press the
[CENTER CANCEL] button.
Button lit: ON
Button unlit: OFF
1. Hold down the [CANCEL/SHIFT] button and press the
[V-LINK] button.
2. Turn the AMP [LEVEL] knob.
3. Press the [CANCEL/SHIFT] button.
Hold down the [CANCEL/SHIFT] button and turn the [PITCH]
knob.
1. Hold down the [CANCEL/SHIFT] button and press the
[V-LINK] button.
2. Hold down the [KEY HOLD] button and press the [EFFECTS
ON/OFF] button.
Button lit: ON
Button unlit: OFF
3. Press the [CANCEL/SHIFT] button.
51