ProCurve Series
2510-24 Switch
www.procurve.com
Installation and
Getting Started Guide

Advertising

   Also See for HP 2510-24

   Summary of Contents for HP 2510-24

  • Page 1

    Installation and Getting Started Guide ProCurve Series 2510-24 Switch www.procurve.com...

  • Page 3

    ProCurve Series 2510 Switch Installation and Getting Started Guide...

  • Page 4

    Publication Number The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and 5991-3833 services. Nothing herein should be construed as constituting an July 2006 additional warranty.

  • Page 5: Table Of Contents

    Rack or Cabinet Mounting ....... 2-11 Rack Mounting the Switch 2510-24 ......2-12 Horizontal Surface Mounting .

  • Page 6: Table Of Contents

    7. (Optional) Connect a Console to the Switch ....2-17 Terminal Configuration ........2-17 Direct Console Access .

  • Page 7: Table Of Contents

    A Switch Specifications Physical ..........A-1 Electrical .

  • Page 8: Table Of Contents

    EMC Regulatory Statements ........C-8 U.S.A........... . . C-8 Canada .

  • Page 9

    Introducing the Switch The ProCurve Switch 2510-24 is a multiport switch that can be used to build high-performance switched workgroup networks. These switches are store- and-forward devices offering low latency for high-speed networking. ProCurve Switch 2510-24 (J9019A) Link Mode Spd mode:...

  • Page 10: Front Of The Switch

    Locator LEDs Link Mode Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps 10/100Base-T Ports (1 - 24) — Ports are HP Auto MDI-X ProCurve Switch Link Link 2510-24 Mode Mode J9019A Dual-Personality Ports:...

  • Page 11: Leds

    Introducing the Switch Front of the Switch LEDs Table 1-1. Switch LEDs Switch LEDs State Meaning Power The switch is receiving power. (green) The switch is NOT receiving power. Fault The normal state; indicates there are no fault conditions on the switch. (orange) Blinking* A fault has occurred on one of the switch ports.

  • Page 12: Led Mode Select Button And Indicator Leds

    Port LEDs (two for each port) Link and Mode Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps 10/100Base-T Ports (1 - 24) — Ports are HP Auto MDI-X ProCurve Switch Link Mode Link Mode 2510-24...

  • Page 13: Reset Button

    Introducing the Switch Front of the Switch If the Full Duplex (FDx) indicator LED is lit, the port LEDs light for those ■ ports that are operating in full duplex. ■ If the Speed (Spd) indicator LED is lit, the port LEDs behave as follows to indicate the connection speed for the port: •...

  • Page 14: Back Of The Switch

    Introducing the Switch Back of the Switch Back of the Switch ProCurve Switch 2510-24 (J9019A) AC power connector Power Connector The Series 2510 Switch does not have a power switch; it is powered on when connected to an active AC power source. This switch automatically adjusts to any voltage between 100-240 volts and either 50 or 60 Hz.

  • Page 15: Switch Features

    Introducing the Switch Switch Features Switch Features The features of the Series 2510 Switch include: ■ 24 auto-sensing 10/100Base-TX RJ-45 ports. ■ two dual-personality ports—either the auto sensing 10/100/1000Base-T RJ-45 or the mini-GBIC can be used for each port. ■ plug-and-play networking—all ports are enabled—just connect the network cables to active network devices and your switched network is operational.

  • Page 17: Included Parts

    Installing the Switch The ProCurve Series 2510 Switch is easy to install. It comes with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, in an equipment cabinet, on a wall, and with rubber feet that can be attached so the switch can be securely located on a horizontal surface.

  • Page 18

    Installing the Switch Included Parts ■ Power cord, one of the following: Australia/New Zealand 8120-6803 China 8120-8377 Continental Europe 8120-6802 Denmark 8120-6806 Japan 8120-6804 Switzerland 8120-6807 8120-8709 United Kingdom/Hong Kong/Singapore United States/Canada/Mexico 8120-6805 South Africa 8120-8929 Israel 8121-1009 Thailand 8121-0673 Taiwan 8121-0964 J a p a n P o w e r...

  • Page 19: Physical

    Installing the Switch Installation Procedures Installation Procedures Summary Follow these steps to install the switch. The rest of this chapter provides details on these steps. Prepare the installation site (page 2-5). Ensure the physical environ- ment is properly prepared, including having the correct network cabling ready to connect to the switch and having an appropriate location for the switch.

  • Page 20: Connectors

    Installing the Switch Installation Procedures Installation Precautions: Follow these precautions when installing the Series 2510 Switch. W A R N I N G The rack or cabinet should be adequately secured to prevent it ■ from becoming unstable and/or falling over. Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at the bottom and progressively lighter devices installed above.

  • Page 21: Prepare The Installation Site

    Installing the Switch Installation Procedures 1. Prepare the Installation Site ■ Cabling Infrastructure - Ensure the cabling infrastructure meets the necessary network specifications. See the following table for cable types and lengths, and see appendix B, “Cables and Connectors” for more information: Table 2-1.

  • Page 22

    Installing the Switch Installation Procedures Port Type Cable Type Length Limits Fiber Optic Cables • 62.5 μm cable: Gigabit-SX Multimode fiber-optic cables designed for Gigabit Ethernet: 62.5/125 μm or 50/125 μm (on Gigabit-SX-LC – 160 MHz*km = 220 meters mini-GBIC) (core/cladding) diameter, low metal content, –...

  • Page 23: Lasers

    Installing the Switch Installation Procedures 2. Installing or Removing mini-GBICs You can install or remove a mini-GBIC from a mini-GBIC slot without having to power off the switch. Use only ProCurve mini-GBICs. N o t e s ■ The mini-GBIC slots are shared with the two 10/100/1000Base-T RJ-45 ports.

  • Page 24

    Installing the Switch Installation Procedures Removing the mini-GBICs N o t e The network cable should be disconnected from the mini-GBIC before removing it from the switch. Depending on when you purchased your ProCurve mini-GBIC, it may have either of three different release mechanisms: a plastic tab on the bottom of the mini-GBIC, a plastic collar around the mini-GBIC, or a wire bail.

  • Page 25: Electrical

    Installing the Switch Installation Procedures 3. Verify the Switch Passes Self Test Before mounting the switch in its network location, you should first verify it is working properly by plugging it into a power source and verifying it passes self test. Connect the power cord supplied with the switch to the power connector on the back of the switch, and then into a properly grounded electrical outlet.

  • Page 26: Led Behavior:

    Switch port LEDs ProCurve Switch 2510-24 (J9019A) Link Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps 10/100Base-T Ports (1 - 24) — Ports are HP Auto MDI-X ProCurve Switch Link Mode Link Mode 2510-24...

  • Page 27: Mount The Switch

    Installing the Switch Installation Procedures 4. Mount the Switch After the switch passes self test, you are ready to mount the switch in a stable location. The Series 2510 Switch can be mounted in these ways: ■ in a rack or cabinet ■...

  • Page 28: Rack Mounting The Switch 2510-24

    Installing the Switch Installation Procedures Rack Mounting the Switch 2510-24 Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. 8 mm M4 screws N o t e The mounting brackets have multiple mounting holes and can be rotated allowing for a wide variety of mounting options.

  • Page 29

    Installing the Switch Installation Procedures Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Ensure that the screws are at the same level in each upright.

  • Page 30: Horizontal Surface Mounting

    Installing the Switch Installation Procedures Install the other number 12-24 screw into the upper hole in each bracket. Tighten these screws. Install additional screw Horizontal Surface Mounting Place the switch on a table or other horizontal surface. The switch comes with rubber feet in the accessory kit that can be used to help keep the switch from sliding on the surface.

  • Page 31: Wall Mounting

    Installing the Switch Installation Procedures Wall Mounting C a u t i o n The switch can only be mounted with the RJ-45 ports facing up. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. Attach the switch to the wall or wood surface with two 5/8-inch number 12 wood screws (not included).

  • Page 32: Connect The Network Cables

    = 1 0 00 Mbps 10/1 00B ProCur ve Switch Link Mode Link 2510-24 until the tab on the plug clicks into J9019A place. When power is on for the switch ator Mode and for the connected device, the Link...

  • Page 33: Optional) Connect A Console To The Switch

    Installing the Switch Installation Procedures 7. (Optional) Connect a Console to the Switch The switch has a full-featured, easy to use console interface for performing switch management tasks including the following: ■ Monitor switch and port status and observe network activity statistics ■...

  • Page 34: Direct Console Access

    “Press any key to continue”. Press a key, and you will then see the switch console command (CLI) prompt, for example: ProCurve Switch 2510-24# If you want to continue with console management of the switch at this time, see chapter 3, for some basic configuration steps.

  • Page 35: Sample Network Topologies

    ProCur ve Swi tch Spd mode: of f = 1 0 Mbps, flash = 1 0 0 Mbps, on = 1 0 00 Mbps 10/1 00Base-T P orts (1 - 24) — P orts are HP A uto MDI-X 2510-24 Link Mode Link...

  • Page 36: As A Segment Switch

    Installing the Switch Sample Network Topologies As a Segment Switch Servers with Gigabit Ethernet NIC HP ProCurve Switch 2824 To backbone Power Fault Fast Ethernet Switch Fast Ethernet Switch hp procurve hp procurve switch 2650 switch 2650 J4899A J4899A Power...

  • Page 37

    Installing the Switch Sample Network Topologies Because the Switch has the “IEEE Auto MDI/MDI-X” features, the connections between the switch and the hubs, and between the switch and end nodes or servers can be through category 5 straight-through or crossover twisted-pair cable.

  • Page 38: Connecting To A Backbone Switch

    5304xl Act FDx Reset Clear Self Power Modules LED Mode Select J4850A Use xl modules only Console Test Power Fault HP ProCurve Switch 2824 Link Link Mode module Mode module J4878A J4878A 100/1000Base-T Ports Power Link Link Mode Fault...

  • Page 39: Stacking The Switch

    N o t e In the Backbone Switch illustration, the 1000 Mbps fiber-optic connection between the Switch 2510-24 and the Switch 5304xl is by way of a Gigabit-SX mini-GBIC installed in the Switch 2510-24 and connected to a Gigabit-SX Module in the Switch 5304xl.

  • Page 41: Recommended Minimal Configuration

    Configuring the Switch This chapter is a guide for using the console Switch Setup screen to quickly assign an IP (Internet Protocol) address and subnet mask to the switch, set a Manager password, and, optionally, configure other basic features. For more information on using the switch console and the other switch management interfaces: the web browser interface, please see the Manage- ment and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

  • Page 42: Using The Console Setup Screen

    (the default display). The CLI prompt appears displaying the switch model number, for example: ProCurve Switch 2510-24# At the prompt, enter the setup command to display the Switch Setup screen. The following illustration shows the Setup screen with the default settings.

  • Page 43

    Configuring the Switch to the IP Config (DHCP/Bootp) field and use the Space bar to select the [Tab] Manual option. to the IP Address field and enter the IP address that is compatible with [Tab] your network. to the Subnet Mask field and enter the subnet mask used for your [Tab] network.

  • Page 44: Where To Go From Here

    Configuring the Switch Where to Go From Here The above procedure configures your switch with a Manager password, IP address, and subnet mask. As a result, with the proper network connections, you can now manage the switch from a PC equipped with Telnet or a web browser interface.

  • Page 45: Using The Ip Address For Remote Switch Management

    Press a key, and you will then see the switch console command (CLI) prompt, for example: ProCurve Switch 2510-24# Enter help or ? to see a list of commands that can be executed at the prompt. Entering any command followed by help provides more detailed context help information about the command.

  • Page 46

    Configuring the Switch Using the IP Address for Remote Switch Management For more information on using the web browser interface, please see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com. An extensive help system is also available for the web browser interface. To access the help system though the subnet on which the switch is installed you must have access to the internet.

  • Page 47: Basic Troubleshooting Tips

    Troubleshooting This chapter describes how to troubleshoot the Series 2510 Switch. This document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting on the Series 2510 Switch using the software tools available with the switch, including the full-featured console interface, the built-in web browser interface.

  • Page 48

    Troubleshooting Basic Troubleshooting Tips Because the Series 2510 Switch behaves in this way (in compliance with the IEEE 802.3 standard), if a device connected to the switch has a fixed configuration at full duplex, the device will not connect correctly to the switch.

  • Page 49

    Troubleshooting Basic Troubleshooting Tips ■ Check the port configuration. A port on your Switch may not be operating as you expect because it has been put into a “blocking” state by Spanning Tree, GVRP (automatic VLANs), or LACP (automatic trunking). (Note that the normal operation of the Spanning Tree, GVRP, and LACP features may put the port in a blocking state.) Or, the port just may have been configured as disabled through software.

  • Page 50: Diagnosing With The Leds

    Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Table 3-1 shows LED patterns on the switch and the switch modules that indicate problem conditions. Check in the table for the LED pattern you see on your switch. Refer to the corresponding diagnostic tip on the next few pages. Table 4-1.

  • Page 51

    Troubleshooting Diagnosing with the LEDs Diagnostic Tips: Problem Solution ➊ The switch is not 1. Verify the power cord is plugged into an active power source and to the switch. Make sure these connections are snug. plugged into an active AC power 2.

  • Page 52

    Troubleshooting Diagnosing with the LEDs Problem Solution ➎ The network Try the following procedures: connection is not • For the indicated port, verify both ends of the cabling, at the switch and the connected working device, are connected properly. properly. •...

  • Page 53

    Troubleshooting Diagnosing with the LEDs Problem Solution ➏ Use the switch console to see if the port is part of a dynamic trunk (through the LACP The port may be improperly feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may configured, or have been put into a “blocking”...

  • Page 54: Proactive Networking

    Troubleshooting Proactive Networking Proactive Networking The ProCurve Series 2510 Switch devices have built-in management capabil- ities that proactively help you manage your network including: ■ finding and helping you fix the most common network error conditions (for example, faulty network cabling, and non-standard network topolo- gies) informing you of the problem with clear, easy-to-understand messages ■...

  • Page 55: Hardware Diagnostic Tests

    Troubleshooting Hardware Diagnostic Tests Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either: ■ Unplug and plug in the power cord (power cycling) Press the Reset button on the front of the switch ■...

  • Page 56: Testing Twisted-pair Cabling

    Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling Network cables that fail to provide a link or provide an unreliable link between the switch and the connected network device may not be compatible with the IEEE 802.3 Type 10Base-T, 100Base-TX. The twisted-pair cables attached to the Switch must be compatible with the appropriate standards.

  • Page 57: Restoring The Factory Default Configuration

    Troubleshooting Restoring the Factory Default Configuration Restoring the Factory Default Configuration As part of your troubleshooting process on the Switch, it may become neces- sary to return the switch configuration to the factory default settings. This process momentarily interrupts the switch operation, clears any passwords, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the switch into its factory default configuration including deleting the IP address, if one is configured.

  • Page 58: Downloading New Switch Software

    Troubleshooting Downloading New Switch Software Downloading New Switch Software When product enhancements occur for the Series 2510 Switch, new software can be downloaded to the switch through several methods, for product enhancements and new features. For more information, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

  • Page 59: Environmental

    Switch Specifications Physical 2510-24 (J9019A) Width: 44.3 cm (17.42 in) Depth: 23.5 cm (9.3 in) Height: 4.4 cm (1.73 in) Weight: 2.2 kg (4.9 lbs) Electrical The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz.

  • Page 60

    Switch Specifications Connectors ■ The 10/100 Mbps RJ-45 twisted-pair ports are compatible with the following standards: • IEEE 802.3u 100Base-TX • IEEE 802.3 10Base-T The 1000 Mbps LC fiber-optic ports on the Gigabit-SX and Gigabit-LX ■ mini- GBIC transceivers are compatible with the IEEE 802.3z Gigabit-SX and Gigabit-LX standards.

  • Page 61: Switch Ports

    Switch Ports and Network Cables This appendix includes switch connector information and network cable information for cables that should be used with the Series 2510 Switch, including minimum pin-out information and specifications for twisted-pair cables. N o t e Incorrectly wired cabling is the most common cause of problems for LAN communications.

  • Page 62

    Switch Ports and Network Cables Because of the increased speed provided by 1000Base-T (Gigabit-T), network cable quality is more important than for either 10Base-T or 100Base-TX. Cabling plants being used to carry 1000Base-T networking must comply with the IEEE 802.3ab standards. In particular, the cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT).

  • Page 63: Mode Conditioning Patch Cord For Gigabit-lx

    Switch Ports and Network Cables Mode Conditioning Patch Cord for Gigabit-LX Mode Conditioning Patch Cord for Gigabit-LX The following information applies to installations in which multimode fiber- optic cables are connected to a Gigabit-LX port. Unlike Gigabit-SX, which connects to only multimode fiber-optic cabling, Gigabit-LX can use either single-mode or multimode cable.

  • Page 64: Installing The Patch Cord

    Switch Ports and Network Cables Mode Conditioning Patch Cord for Gigabit-LX Installing the Patch Cord As shown in the illustration below, connect the patch cord to the Gigabit-LX mini-GBIC with the section of single-mode fiber plugged in to the Tx (transmit) port.

  • Page 65: Twisted-pair Cable/connector Pin-outs

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable/Connector Pin-Outs If you connect a Series 2510 Switch twisted-pair port to another switch or hub, which typically have MDI-X ports, the Series 2510 Switch port automatically operates as an MDI port. If you connect it to an end node, such as a server or PC, which typically have MDI ports, the Series 2510 Switch port operates as an MDI-X port.

  • Page 66: Straight-through Twisted-pair Cable For 10 Mbps Or 100 Mbps Network Connections

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because of the MDI/MDI-X operation of the 10/100 ports on the switch, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use “straight-through”...

  • Page 67: Crossover Twisted-pair Cable For 10 Mbps Or 100 Mbps Network Connection

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection The MDI/MDI-X operation of the 10/100 ports on the switch also allows you to use “crossover” cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches.

  • Page 68

    Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs...

  • Page 69: Safety Information

    Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death.

  • Page 70: Informations Concernant La Sécurité

    Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.

  • Page 71: Hinweise Zur Sicherheit

    Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann.

  • Page 72: Considerazioni Sulla Sicurezza

    Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simbolo di riferimento alla documentazione. Se il prodotto è contras- segnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o morte.

  • Page 73: Consideraciones Sobre Seguridad

    Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.

  • Page 74: Safety Information (japan)

    Safety and EMC Regulatory Statements Safety Information (Japan) Safety Information (Japan) J a p a n P o w e r C o r d W a r n i n g...

  • Page 75: Safety Information (china)

    Safety and EMC Regulatory Statements Safety Information (China) Safety Information (China)

  • Page 76: Emc Regulatory Statements

    Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

  • Page 77: Korea

    Safety and EMC Regulatory Statements EMC Regulatory Statements Korea Taiwan...

  • Page 78: European Community

    Safety and EMC Regulatory Statements EMC Regulatory Statements European Community C-10...

  • Page 79: Waste Electrical And Electronic Equipment (weee) Statements

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.

  • Page 80

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että...

  • Page 81

    Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnan- dole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.

  • Page 82

    Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido.

  • Page 83

    Index Numerics buttons Clear button … 1-5 10/100/1000Base-TX ports LED Mode select button … 1-4 location on switch … 1-2 Reset button … 1-5 1000Base-LH connections, length limitations … 2-6 ports, cables used with … 2-6, B-2 1000Base-LX cabinet connections, length limitations … 2-6 mounting the switch in …...

  • Page 84

    Clear button DHCP deleting passwords … 1-5 automatic switch configuration … 3-2 description … 1-5 for in-band access … 2-17 location on switch … 1-2, 1-5 diagnostic tests … 4-9 restoring factory default configuration … 1-5, checking the console messages … 4-9 4-11 checking the LEDs …...

  • Page 85

    full-duplex fixed configuration showing error conditions … 4-4 effects on network connections … 4-1 FDx … 1-4–1-5 full-duplex operation of mini-GBICs … 2-7 LED Mode View select indicators … 1-4 Link … 1-3 link … 1-4 location on switch … 1-2 horizontal surface Mode mounting switch on …...

  • Page 86

    ports 10/100/1000Base-TX, location on switch … 1-2 network cables connecting to … 2-16 1000Base-LH connections … 2-6 console … 2-17 1000Base-LX connections … 2-6 MDIX feature … B-5 1000Base-SX connections … 2-6 network connections … 2-16 1000Base-T connections … 2-5 power connector …...

  • Page 87

    self test Fault LED behavior … 2-10 Telnet access to the console … 3-5 LED behavior during … 2-10 terminal configuration … 2-17 Power LED behavior … 2-10 Test LED … 1-3 serial cable behavior during factory default reset … 4-11 for direct console connection …...

  • Page 88

    VT-100 terminal serial cable connection for … 2-18 wall mounting the switch on … 2-15 waste electrical and electronic equipment statements … D-1 wiring rules for twisted-pair cables … B-5 6 – Index...

  • Page 90

    Technical information in this document is subject to change without notice. © Copyright 2006 Hewlett-Packard Development Company, L.P. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws. Printed in Taiwan July 2006 Manual Part Number 5991-3833 *5991-3833*...

Comments to this Manuals

Symbols: 0
Latest comments: