Page 1 Camera User Guide • Make sure you read this guide, including the “Safety Precautions” section, before using the camera. • Reading this guide will help you learn to use the camera properly. • Store this guide safely so that you can use it in the future. ENGLISH...
Page 2: Package Contents
Package Contents Before use, make sure the following items are included in the package. If anything is missing, contact your camera dealer. Battery Pack NB-5L Battery Charger Camera (with terminal cover) CB-2LX/CB-2LXE Wrist Strap Interface Cable WS-DC11 IFC-400PCU DIGITAL CAMERA Warranty Card Getting Started Solution Disk (CD-ROM) * Contains software and PDF manuals (= 2 7). • A memory card is not included (see below). Compatible Memory Cards The following memory cards (sold separately) can be used, regardless of capacity. • SD memory cards • SDHC memory cards • SDXC memory cards • Eye-Fi cards * Conforms to SD speciications. However, not all memory cards have been veriied to work with the camera. About Eye-Fi Cards This product is not guaranteed to support Eye-Fi card functions (including wireless transfer). In case of an issue with an Eye-Fi card, please check with the card manufacturer.
Page 3: Preliminary Notes And Legal Information
Preliminary Notes and Legal Information • Take and review some test shots initially to make sure the images were recorded correctly. Please note that Canon Inc., its subsidiaries and afiliates, and its distributors are not liable for any consequential damages arising from any malfunction of a camera or accessory, including memory cards, that results in the failure of an image to be recorded or to be recorded in a way that is machine readable. • Images recorded by the camera are intended for personal use. Refrain from unauthorized recording that infringes on copyright law, and note that even for personal use, photography may contravene copyright or other legal rights at some performances or exhibitions, or in some commercial settings. • The camera warranty is valid only in the area of purchase. In case of camera problems while abroad, return to the area of purchase before contacting a Canon Customer Support Help Desk. • Although the LCD monitor is produced under extremely high-precision manufacturing conditions and more than 99.99% of the pixels meet design speciications, in rare cases some pixels may be defective or may appear as red or black dots. This does not indicate camera damage or affect recorded images. • The LCD monitor may be covered with a thin plastic ilm for protection against scratches during shipment. If covered, remove the ilm before using the camera. • When the camera is used over an extended period, it may become warm. This does not indicate damage. Organization of Camera User Guide The following guides are included, each used for different purposes.
Page 4: Part Names And Conventions In This Guide
Part Names and Conventions in This Guide Zoom lever Lamp Shooting: / Power button <j (wide angle)> Flash Playback: <k (magnify)> / Control ring <g (index)> Tripod socket Microphone Memory card/battery cover Lens DC coupler terminal cover Mode dial Shutter button • In this guide, icons are used to represent the corresponding camera buttons and dials on which they appear or which they resemble. • The following camera buttons and controls are represented by icons. <o> Up button on back <q> Left button on back <r> Right button on back Down button on back <7> Control dial on back <y> Control ring on front • Shooting modes and on-screen icons and text are indicated in brackets.
Page 5 Part Names and Conventions in This Guide Strap mount <n> button Screen (LCD monitor) <1 (Playback)> button Indicator / < (Wireless LAN)> / Up button < (Ring function selector)> / <a (Single image erase)> button <e (Macro)> / <f (Manual focus)> / Left button Indicator Control dial Movie button FUNC./SET button Speaker <h (Flash)> / Right button DIGITAL terminal <l (Display)> / Down button HDMI terminal * Gestures may not be detected as easily if you apply a screen protector. In this case, increase the sensitivity of the touch-screen panel (= 2 73). Turning the control dial is one way to choose setting items, switch images, and perform other operations. Most of these operations are also possible with the <o><q><r> buttons. • For convenience, all supported memory cards are simply referred to as “the memory card”. • The tabs shown above titles indicate whether the function is used for still images, movies, or both. : I ndicates that the function is used when shooting or Still Images viewing still images.
Page 6: Table Of Contents
Table of Contents Package Contents ......2 Geotagging Images on the Camera ........78 Compatible Memory Cards ....2 Other Information ......78 Preliminary Notes and Legal Information ........3 Organization of Camera User Advanced Guide ..... 85 Guide ..........3 Part Names and Conventions in Camera Basics .....85 This Guide........4 Table of Contents ......6 On/Off ..........86 Contents: Basic Operations ...8 Shutter Button ......87 Safety Precautions .......10 Shooting Modes ......88 Shooting Display Options ....88 FUNC. Menu .
Page 7 Table of Contents P Mode ........165 Setting Menu ......261 Shooting in Program AE Mode Adjusting Basic Camera ( Mode) ........166 Functions ........262 Image Brightness (Exposure Accessories .......277 Compensation) ......166 Color and Continuous Tips on Using Included Shooting ........174 Accessories........278 Shooting Range and Optional Accessories ....278 Focusing ........181 Using Optional Accessories ..281 Flash ..........193 Printing Images ......286 Shooting RAW Images ....198 Using an Eye-Fi Card....300 Other Settings ......199 Appendix ......303 Tv, Av, M, and C Mode ..201 Troubleshooting ......304 Speciic Shutter Speeds On-Screen Messages ....310 (<Tv> Mode) ......202...
Page 8: Contents: Basic Operations
Contents: Basic Operations Shoot Use camera-determined settings (Auto Mode) ........96 Shooting people well Portraits Against Snow Smooth Skin (= 1 37) (= 1 38) (= 1 41) Matching speciic scenes Under Water Fireworks Night Scenes (= 1 38) (= 1 38) (= 1 37) Applying special effects Vivid Colors Poster Effect “Aged” Photos Fish-Eye Effect...
Page 9 Contents: Basic Operations Use Face ID ................113, 222 Movie clips and photos together (Movie Digest) ........ 136 1 View View images (Playback Mode) ............216 Automatic playback (Slideshow) ............234 On a TV ....................281 On a computer ..................28 Browse through images quickly ............224 Erase images ..................240 E Shoot/View Movies Shoot movies ................96, 161 View movies (Playback Mode) ............216 Fast-moving subjects, slow-motion playback ........162 c Print Print pictures ..................286 Save Save images to a computer ..............28...
Page 10: Safety Precautions
• Do not attempt to disassemble, alter or apply heat to the product. • Avoid dropping or subjecting the product to severe impacts. • To avoid the risk of injury, do not touch the interior of the product if it has been dropped or otherwise damaged. • Stop using the product immediately if it emits smoke, a strange smell, or otherwise behaves abnormally. • Do not use organic solvents such as alcohol, benzine, or thinner to clean the product. • Do not let the product come into contact with water (e.g. sea water) or other liquids. • Do not allow liquids or foreign objects to enter the camera. This could result in electrical shock or ire. If liquids or foreign objects come into contact with the camera interior, immediately turn the camera off and remove the battery. If the battery charger becomes wet, unplug it from the outlet and consult your camera distributor or a Canon Customer Support Help Desk. • Use only the recommended battery. • Do not place the battery near or in direct lame. • Unplug the power cord periodically, and using a dry cloth, wipe away any dust and dirt that has collected on the plug, the exterior of the power outlet, and the surrounding area. • Do not handle the power cord with wet hands. • Do not use the equipment in a manner that exceeds the rated capacity of the electrical outlet or wiring accessories. Do not use if the power cord or plug are damaged, or not fully plugged into the outlet. • Do not allow dirt or metal objects (such as pins or keys) to contact the terminals or plug.
Page 11 Safety Precautions The battery may explode or leak, resulting in electrical shock or ire. This could cause injury and damage the surroundings. In the event that a battery leaks and the battery electrolyte contacts eyes, mouth, skin or clothing, immediately lush with water. • Turn the camera off in places where camera use is prohibited. The electromagnetic waves emitted by the camera may interfere with the operation of electronic instruments and other devices. Exercise adequate caution when using the camera in places where use of electronic devices is restricted, such as inside airplanes and medical facilities. • Do not play the supplied CD-ROM(s) in any CD player that does not support data CD-ROMs. It is possible to suffer hearing loss from listening with headphones to the loud sounds of a CD-ROM played on an audio CD player (music player). Additionally, this could damage the speakers. Denotes the possibility of injury. Caution • When holding the camera by the strap, be careful not to bang it, subject it to strong impacts or shocks, or let it get caught on other objects. • Be careful not to bump or push strongly on the lens. This could lead to injury or damage the camera. • Be careful not to subject the screen to strong impacts. If the screen cracks, injury may result from the broken fragments. • When using the lash, be careful not to cover it with your ingers or clothing. This could result in burns or damage to the lash. • Avoid using, placing or storing the product in the following places: - Places subject to strong sunlight - Places subject to temperatures above 40 °C (104 °F) - Humid or dusty areas These could cause leakage, overheating or an explosion of the battery, resulting in electrical shock, ire, burns or other injuries. High temperatures may cause deformation of the camera or battery charger casing. • The slideshow transition effects may cause discomfort when viewed for prolonged periods.
Page 12 Safety Precautions Denotes the possibility of damage to the equipment. Caution • Do not aim the camera at bright light sources (such as the sun on a clear day). Doing so may damage the image sensor. • When using the camera on a beach or at a windy location, be careful not to allow dust or sand to enter the camera. • Do not push down on the lash, or pry it open. This may cause the product to malfunction. • In regular use, small amounts of smoke may be emitted from the lash. This is due to the high intensity of the lash burning dust and foreign materials stuck to the front of the unit. Please use a cotton swab to remove dirt, dust or other foreign matter from the lash to prevent heat build-up and damage to the unit. • Remove and store the battery when you are not using the camera. If the battery is left inside the camera, damage caused by leakage may occur. • Before you discard the battery, cover the terminals with tape or other insulators. Contacting other metal materials may lead to ire or explosions. • Unplug the battery charger from the power outlet after charging is complete, or when you are not using it. • Do not place anything, such as cloth, on top of the battery charger while it is charging. Leaving the unit plugged in for a long period of time may cause it to overheat and distort, resulting in ire. • Do not place the battery near pets. Pets biting the battery could cause leakage, overheating or explosion, resulting in ire or damage. • Do not sit down with the camera in your pocket. Doing so may cause malfunctions or damage the screen. •...
Page 13: Basic Guide
Basic Guide Gives basic instructions, from initial preparations to shooting, playback, and saving on a computer...
Page 14: Initial Preparations
Initial Preparations Prepare for shooting as follows. Attaching the Strap Attach the strap. Thread the end of the strap through the strap hole ( ), and then pull the other end of the strap through the loop on the threaded end ( ). The strap can also be attached to the left side of the camera. Holding the Camera Place the strap around your wrist. When shooting, keep your arms close to your body and hold the camera securely to prevent it from moving. If the lash is up, do not rest your ingers on it.
Page 15: Charging The Battery
Initial Preparations Charging the Battery Before use, charge the battery with the included charger. Be sure to charge the battery initially, because the camera is not sold with the battery charged. Remove the battery cover and insert the battery in the charger. Remove the cover from the battery, align the ▲ marks on the battery and charger, and insert the battery by pushing it in ( ) and down ( ). Charge the battery. CB-2LX: Flip out the plug ( ) and plug the charger into a power outlet ( ). CB-2LXE: Plug the power cord into the charger, then plug the other end into a CB-2LX power outlet. The charging lamp turns orange and charging begins. When the charging is inished, the lamp turns green. CB-2LXE Remove the battery. After unplugging the battery charger, remove the battery by pushing it in ( ) and up ( ). • To protect the battery and keep it in optimal condition, do not charge it continuously for more than 24 hours. • For battery chargers that use a power cord, do not attach the charger or cord to other objects. Doing so could result in malfunction or damage to the product.
Page 16: Inserting The Battery And Memory Card
Initial Preparations • For details on charging time and the number of shots and recording time possible with a fully charged battery, see “Speciications” (= 3 33). Inserting the Battery and Memory Card Insert the included battery and a memory card (sold separately). Note that before using a new memory card (or a memory card formatted in another device), you should format the memory card with this camera (= 2 67). Check the card’s write-protect tab. Recording is not possible on memory cards with a write-protect tab when the tab is in the locked (downward) position. Slide the tab up until it clicks into the unlocked position. Open the cover. Slide the cover ( ) and open it ( ). Insert the battery. While pressing the battery lock in the direction of the arrow, insert the battery as shown and push it in until it clicks into the locked position. If you insert the battery facing the wrong way, it cannot be locked into the correct position. Always conirm that the battery is facing the right way and locks when inserted.
Page 17 Initial Preparations Insert the memory card. Insert the memory card facing as shown until it clicks into the locked position. Make sure the memory card is facing the right way when you insert it. Inserting memory cards facing the wrong way may damage the camera. Terminals Close the cover. Lower the cover ( ) and hold it down as you slide it, until it clicks into the closed position ( ). • For guidelines on how many shots or hours of recording can be saved on one memory card, see “Speciications” (= 3 33). Removing the Battery and Memory Card Remove the battery. Open the cover and press the battery lock in the direction of the arrow. The battery will pop up. Remove the memory card. Push the memory card in until it clicks, and then slowly release it. The memory card will pop up.
Page 18: Setting The Date And Time
Initial Preparations Setting the Date and Time Set the current date and time correctly as follows if the [Date/Time] screen is displayed when you turn the camera on. Information you specify this way is recorded in image properties when you shoot, and it is used when you manage images by shooting date or print images showing the date. You can also add a date stamp to shots, if you wish (= 1 12). Turn the camera on. Press the power button. The [Date/Time] screen is displayed. Set the date and time. Press the <q><r> buttons to choose an option. Press the <o> buttons or turn the <7> dial to specify the date and time. When inished, press the <m> button. Set the home time zone. Press the <q><r> buttons or turn the <7> dial to choose your home time zone. Finish the setup process. Press the <m> button when inished. After a conirmation message, the setting screen is no longer displayed. To turn off the camera, press the power button.
Page 19 Initial Preparations • Unless you set the date, time, and home time zone, the [Date/ Time] screen will be displayed each time you turn the camera on. Specify the correct information. • To set daylight saving time (1 hour ahead), choose [ ] in step 2 and then choose [ ] by pressing the <o> buttons or turning the <7> dial. • You can also set the date and time by touching the desired setting on the screen in step 2 and then touching [o][p], followed by [ ]. Similarly, you can also set your home time zone by touching [q][r] on the screen in step 3, followed by [ Changing the Date and Time Adjust the date and time as follows. Access the camera menu. Press the <n> button. Choose [Date/Time]. Move the zoom lever to choose the [3] tab. Press the <o> buttons or turn the <7> dial to choose [Date/Time], and then press the <m> button. Change the date and time. Follow step 2 on = 1 8 to adjust the settings. Press the <n> button to close the menu.
Page 20: Display Language
Initial Preparations • Date/time settings can be retained for about 3 weeks by the camera’s built-in date/time battery (backup battery) after the battery pack is removed. • The date/time battery will be charged in about 4 hours once you insert a charged battery or connect the camera to an AC adapter kit (sold separately, = 2 78), even if the camera is left off. • Once the date/time battery is depleted, the [Date/Time] screen will be displayed when you turn the camera on. Follow the steps on = 1 8 to set the date and time. Display Language Change the display language as needed. Enter Playback mode. Press the <1> button. Access the setting screen. Press and hold the <m> button, and then immediately press the <n> button. Set the display language. Press the <o><q><r> buttons or turn the <7> dial to choose a language, and then press the <m> button. Once the display language has been set, the setting screen is no longer displayed.
Page 21: Trying The Camera Out
Trying the Camera Out • The current time is displayed if you wait too long in step 2 after pressing the < m > button before you press the <n> button. In this case, press the < m > button to dismiss the time display and repeat step 2. • You can also change the display language by pressing the <n> button and choosing [Language ] on the [3] tab. • You can also set the display language by touching a language on the screen in step 3 and then touching it again. Still Images Movies Trying the Camera Out Follow these instructions to turn the camera on, shoot still images or movies, and then view them. Shooting (Smart Auto) For fully automatic selection of the optimal settings for speciic scenes, simply let the camera determine the subject and shooting conditions. Turn the camera on. Press the power button. The startup screen is displayed. Enter <A> mode. Set the mode dial to <A>. Aim the camera at the subject. The camera will make a slight clicking noise as it determines the scene. Icons representing the scene and image stabilization mode are displayed in the upper right of the screen. Frames displayed around any detected subjects indicate that they are in focus.
Page 22 Trying the Camera Out Compose the shot. To zoom in and enlarge the subject, move the zoom lever toward (telephoto), and to zoom away from the subject, move it toward <j> (wide angle). Shoot. Shooting Still Images Focus. Press the shutter button lightly, halfway down. The camera beeps twice after focusing, and green frames are displayed to indicate image areas in focus. The lash automatically rises in low-light conditions. Shoot. Press the shutter button all the way down. As the camera shoots, a shutter sound is played, and in low-light conditions when the lash is up, it ires automatically. Keep the camera still until the shutter sound ends. Your shot is only displayed until the camera is ready to shoot again.
Page 23 Trying the Camera Out Shooting Movies Start shooting. Press the movie button. The camera beeps once as recording begins, and [ Rec] is displayed with the elapsed time. Elapsed Time Black bars displayed on the top and bottom edges of the screen indicate image areas not recorded. Frames displayed around any detected faces indicate that they are in focus. Once recording begins, you can take your inger off the movie button. Finish shooting. Press the movie button again to stop shooting. The camera beeps twice as recording stops.
Page 24 Trying the Camera Out Viewing After shooting images or movies, you can view them on the screen as follows. Enter Playback mode. Press the <1> button. Your last shot is displayed. Browse through your images. To view the previous image, press the <q> button or turn the <7> dial counterclockwise. To view the next image, press the <r> button or turn the <7> dial clockwise. Press and hold the <q><r> buttons to browse through images quickly. To access Scroll Display mode, turn the <7> dial rapidly. In this mode, turn the <7> dial to browse through images. To return to single-image display, press the <m> button. Movies are identiied by a [ ] icon. To play movies, go to step 3.
Page 25 Trying the Camera Out Play movies. Press the <m> button to access the movie control panel, choose [ ] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button again. Playback now begins, and after the movie Volume is inished, [ ] is displayed. To adjust the volume, press the <o> buttons. • To switch to Shooting mode from Playback mode, press the shutter button halfway. Touch-Screen Operations To view the next image on the screen in step 2, drag left across the screen, and to view the previous image, drag right. To access Scroll Display mode, quickly drag left or right repeatedly. To return to single-image display from Scroll Display mode, touch the image in the middle of the screen. Choose a movie, and touch [ ] to start playback. To adjust the volume during movie playback, quickly drag up or down across the screen.
Page 26 Trying the Camera Out Erasing the Images You can choose and erase unneeded images one by one. Be careful when erasing images, because they cannot be recovered. Choose an image to erase. Press the <q><r> buttons or turn the <7> dial to choose an image. Erase the image. Press the <a> button. After [Erase?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [Erase], and then press the <m> button. The current image is now erased. To cancel erasure, press the <q><r> buttons or turn the <7> dial to choose [Cancel], and then press the <m> button. • You can also erase all images at once (= 2 41). • You can also erase the current image by touching [Erase] on the screen in step 2. • Images can also be erased by using Touch Actions (= 2 48).
Page 27: Included Software, Pdf Manuals
Included Software, PDF Manuals The software and PDF manuals on the included DIGITAL CAMERA Solution Disk (CD-ROM) (= 2 ) are introduced below, with instructions for installation, and saving images to a computer. Software After installing the software on the CD-ROM, you can do the following things on your computer. CameraWindow Import images and change camera settings ImageBrowser EX Manage images: view, search, and organize Print and edit images Digital Photo Professional Browse, process and edit RAW images Auto Update Function Using the included software, you can update to the latest version, and download new functions via the Internet (some software excluded). Be sure to install the software on a computer with an Internet connection so you can use this function. • Internet access is required to use this function, and any ISP account charges and access fees must be paid separately. PDF Manuals Camera User Guide Refer to this guide for a more in-depth understanding of camera operation. Software Guide Refer to this guide when using the included software. The guide can be accessed from the help system of included software (some software excluded).
Page 28: System Requirements
Computers running one of the above operating systems Computer (preinstalled), with an included USB port and Internet connection Still images: Mac OS X 10.7: Core 2 Duo or higher, Still images: 1.6 GHz or higher Mac OS X 10.6: Core Duo 1.83 Processor Movies: Core 2 Duo 2.6 GHz GHz or higher or higher Movies: Core 2 Duo 2.6 GHz or higher Still images Windows 7 (64 bit): 2 GB or Still images more Mac OS X 10.7: 2 GB or more, Windows 7 (32 bit), Vista, Mac OS X 10.6: 1 GB or more XP: 1 GB or more Movies Movies 2 GB or more 2 GB or more Interfaces USB and wireless LAN Free Hard Disk 750 MB or more 640 MB or more Space Display 1024 x 768 resolution or higher * Silverlight 4 or later (max. 100 MB) must be installed, and in Windows XP, Microsoft .NET Framework 3.0 or later (max. 500 MB) must be installed. Installation may take some time, depending on computer performance. • Check the Canon website for the latest system requirements, including supported OS versions.
Page 29: Installing The Software
Included Software, PDF Manuals Installing the Software Windows 7 and Mac OS X 10.6 are used here for the sake of illustration. Using the software auto update function, you can update to the latest version and download new functions via the Internet (some software excluded), so be sure to install the software on a computer with an Internet connection. Insert the CD-ROM in the computer’s CD-ROM drive. Insert the included CD-ROM (DIGITAL CAMERA Solution Disk) (= 2 ) in the computer’s CD-ROM drive. On a Macintosh computer, after inserting the disc, double-click the desktop disc icon to open it, and then double-click the ] icon displayed. Begin the installation. Click [Easy Installation] and follow the on-screen instructions to complete the installation process.
Page 30 Included Software, PDF Manuals When a message is displayed prompting you to connect the camera, connect it to a computer. With the camera turned off, open the cover ( ). With the smaller plug of the included interface cable (= 2 ) in the orientation shown, insert the plug fully into the camera terminal ( ). Insert the larger plug of the interface cable in the computer’s USB port. For details about USB connections on the computer, refer to the computer user manual. Install the iles. Turn the camera on, and follow the on-screen instructions to complete the installation process. The software will connect to the Internet to update to the latest version and download new functions. Installation may take some time, depending on computer performance and the Internet connection. Click [Finish] or [Restart] on the screen after installation and remove the CD- ROM when the desktop is displayed. Turn the camera off and disconnect the cable.
Page 31: Saving Images To A Computer
Included Software, PDF Manuals • When not connected to the Internet, there are the following limitations. - The screen in step 3 will not be displayed. - Some functions may not be installed. • The irst time you connect the camera to the computer, drivers will be installed, so it may take a few minutes until camera images are accessible. • If you have several cameras that were bundled with ImageBrowser EX on the included CD-ROMs, be sure to use each camera with their included CD- ROM and follow the on-screen installation instructions for each. Doing so will ensure that each camera will receive the correct updates and new functions via the auto update function. Saving Images to a Computer Windows 7 and Mac OS X 10.6 are used here for the sake of illustration. Connect the camera to the computer. Follow step 3 on = 3 0 to connect the camera to a computer. Turn the camera on to access CameraWindow. Press the <1> button to turn the camera On a Macintosh computer, CameraWindow is displayed when a connection is established between the camera and computer. For Windows, follow the steps introduced below. In the screen that displays, click the [ link to modify the program.
Page 32 Included Software, PDF Manuals Choose [Downloads Images From Canon Camera using Canon CameraWindow] and then click [OK]. Double click [ Save the images to the CameraWindow computer. Click [Import Images from Camera], and then click [Import Untransferred Images]. Images are now saved to the Pictures folder on the computer, in separate folders named by date. After images are saved, close CameraWindow, press the <1> button to turn the camera off, and unplug the cable. For instructions on viewing images on a computer, refer to the Software Guide (= 2 7).
Page 33 Included Software, PDF Manuals • In Windows 7, if the screen in step 2 is not displayed, click the [ ] icon in the taskbar. • To start CameraWindow in Windows Vista or XP, click [Downloads Images From Canon Camera using Canon CameraWindow] on the screen displayed when you turn the camera on in step 2. If CameraWindow is not displayed, click the [Start] menu and choose [All Programs] ► [Canon Utilities] ► [CameraWindow] ► [CameraWindow]. • On a Macintosh computer, if CameraWindow is not displayed after step 2, click the [CameraWindow] icon in the Dock (the bar at the bottom of the desktop). • Although you can save images to a computer simply by connecting your camera to the computer without using the included software, the following limitations apply. - It may take a few minutes after you connect the camera to the computer until camera images are accessible. - Images shot in vertical orientation may be saved in horizontal orientation. - RAW images (or JPEG images recorded with RAW images) may not be saved. - Image protection settings may be cleared from images saved to a computer. - Some problems may occur when saving images or image information, depending on the operating system version, the software in use, or image ile sizes. - Some functions provided by the included software may not be available, such as editing movies or returning images to the camera. Using the PDF Manuals Camera User Guide Access this guide by double-clicking the desktop shortcut icon.
Page 34: Accessories
DIGITAL Wrist Strap NB-5L CB-2LX/CB-2LXE CAMERA WS-DC11 (with terminal cover) Solution Disk Interface Cable IFC-400PCU Memory Card Card Reader Cable Windows/ Macintosh Power Computer HDMI Cable HTC-100 Stereo AV Cable AVC-DC400ST AC Adapter Kit ACK-DC30 Video System Flash Unit Case Canon PictBridge- Compatible Printers Waterproof Case High-Power Flash WP-DC47 HF-DC2 * Also available for purchase separately. Use of genuine Canon accessories is recommended. This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as ire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis.
Page 35: Wireless Lan Guide
Wireless LAN Guide Describes how to send images wirelessly from the camera to a variety of compatible devices, and how to use the camera with online services...
Page 36: What You Can Do With The Wireless Lan Function
What You Can Do With the Wireless LAN Function This camera is an approved Wi-Fi product. You can wirelessly connect to ®* and send images to the following devices. * Wi-Fi is a brand name that indicates interoperability certiication of wireless LAN devices. Connecting to Web Services CANON iMAGE GATEWAY is an online Social photo service available to those who networking have purchased this product. If you services register for free as a member, you Facebook Video sharing sites Twitter can use CANON iMAGE GATEWAY YouTube to access various Web services, such E-mail as social networking services set on a computer. Connecting to a Smartphone Send images to smartphones and tablet computers that have wireless functions. You can also geotag your shots from a connected smartphone or tablet. Installation of a dedicated application on the smartphone or tablet is required. See the Canon website for details. Connecting to Another Camera Use the wireless function to send images between Canon-brand cameras.
Page 37: Glossary
Glossary Terms related to wireless LAN are explained here. Also refer to the explanations of terms given in the respective sections of this guide. • Access point A device that relays radio wave signals to create a wireless LAN network. This term also refers to a place where you can connect to the Internet via wireless LAN. • Firewall This is a system that protects computers from electronic viruses, external unauthorized access, and security threats. This is set in your wireless LAN router or computer. • SSID/ESSID Numbers and letters used to identify a speciic existing access point. This is also called the “access point name” or “network name”. • Encryption key This is a key used to encrypt data for transmission to and from an access point. • IP address This is an address used to identify a device within a network. • MAC address This is a unique address pre-assigned to a network device. It is also referred to as a “physical address”. The camera can print to PictBridge-compatible printers via wireless LAN. PictBridge technical standards make it easy to connect digital cameras, printers, and other devices directly. Additionally, a new standard called DPS over IP enables PictBridge connections in network environments, and the camera is also compatible with this standard.
Page 38: Wireless Lan Precautions
Wireless LAN Precautions • The model number is PC1819 or PC1882 (including WLAN module model WM217). To identify your model, check the label on the bottom of the camera for a number beginning with PC. • Countries and Regions Permitting WLAN Use - Use of WLAN is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating WLAN regulations, visit the Canon website to check where use is allowed. Note that Canon cannot be held liable for any problems arising from WLAN use in other countries and regions. • Doing any of the following may incur legal penalties: - Altering or modifying the product - Removing the certiication labels from the product • According to foreign exchange and foreign trade law regulations, export permission (or service transaction permission) from the Japanese government is necessary to export strategic resources or services (including this product) outside Japan. • Because this product includes American encryption software, it falls under U.S. Export Administration Regulations, and cannot be exported to or brought into a country under U.S. trade embargo. • Be sure to make notes of the wireless LAN settings you use. The wireless LAN settings saved to this product may be erased due to incorrect operation of the product, the effects of radio waves or static electricity, accident or malfunction. Be sure to make notes of wireless LAN settings as a precaution. Please note that Canon accepts no responsibility for degradation of content, direct or indirect damages or loss of revenue arising from use of the product. •...
Page 39: Radio Wave Interference Precautions
Wireless LAN Precautions • Be sure to use the product as directed in this guide. Be sure to use the wireless LAN function of this product within the guidelines noted in this guide. Canon accepts no responsibility for damages or loss even if the function and product are used in ways other than as described in this guide. • Do not use the wireless LAN function of this product near medical equipment or other electronic equipment. Use of the wireless LAN function near medical equipment or other electronic equipment may affect operation of those devices. Radio Wave Interference Precautions • This product may receive interference from other devices that emit radio waves. To avoid interference, be sure to use this product as far away as possible from such devices, or avoid using the devices at the same time as this product.
Page 40 Wireless LAN Precautions FCC/IC Notice Model: PC1882 (including WLAN Module Model WM217, FCC ID: AZD217) The available scientii c evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such i ndings have not been con- i rmed by additional research. This model has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This product is installed with the WLAN Module which is certiied to standards set by IDA Singapore.
Page 41: Security Precautions
Security Precautions Since wireless LAN uses radio waves to transmit signals, tighter security precautions are necessary than when using a LAN cable. When using wireless LAN, keep the following points in mind. • Only use networks you are authorized to use. This product searches for wireless LAN networks in the vicinity and displays the results on the screen. Networks you are not authorized to use (unknown networks) may also be displayed. However, connecting to or attempting to use those networks could be regarded as unauthorized access. Be sure to use only networks you are authorized to use, and do not attempt to connect to other unknown networks. If security settings have not been properly set, the following problems may occur. • Transmission monitoring Third parties with malicious intent may monitor wireless LAN transmissions and attempt to acquire the data you are sending. • Unauthorized network access Third parties with malicious intent may gain unauthorized access to the network you are using and steal, modify, or destroy information. Additionally, you could fall victim to other types of unauthorized access such as impersonation (where someone assumes an identity to gain access to unauthorized information) and springboard attacks (where someone gains unauthorized access to your network as a springboard to cover their tracks when iniltrating other systems). To prevent these types of problems from occurring, be sure to thoroughly secure your wireless LAN network. Be sure to use the wireless LAN function of this camera with a proper understanding of wireless LAN security, and balance risk and convenience when adjusting security settings.
Page 42: Using Wireless Lan To Send Images From The Camera
• Connecting with the computer • Connecting with the computer • Registering Web services (= 4 5) • Preparing to register a computer • Adjusting settings for using (= 5 6) Web services from CANON iMAGE GATEWAY (= 4 6) • Installing the dedicated CameraWindow application on the smartphone Adding the target device/destination to the camera (= 4 5) (= 5 0) (= 5 4) (= 6 2)
Page 43: Registering A Camera Nickname (First Time Only)
Registering a Camera Nickname (First time only) To start with, register a camera nickname. This nickname will be displayed on the screen of target devices when connecting to other devices via wireless LAN. Access the wireless LAN screen. Press the <1> button to turn the camera Press the <o> button. Access the keyboard. Press the <m> button. Enter a nickname. Touch characters on the keyboard to enter them. Up to 16 characters can be used. Touch [q][r] to move the cursor. Touch [ ] to enter capital letters. Touch [ ] to enter numbers or symbols. Touch [ ] to delete the previous character. Either touch [ ] or press the <n> button. Press the <o> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 44 Registering a Camera Nickname (First time only) • When connecting wirelessly with any device other than a computer, a memory card must be inserted in the camera. Additionally, the memory card must contain images in order for you to access Web services or connect to a smartphone or printer wirelessly. • To change the camera’s nickname, choose [Wireless LAN Settings] on the [3] tab, and then choose [Change Device Nickname]. • You can also enter information by pressing the <o><q><r> buttons or turning the <7> dial to select characters, and then pressing the <m> button. Move the cursor by turning the <y> ring, and press the < > button to delete characters, as needed. • The wireless LAN menu cannot be accessed by pressing the <o> button during detailed information display (= 2 19). To access the menu, irst switch the viewing mode by pressing the button.
Page 45: Connecting To Web Services
Connecting to Web Services Set up the camera to use a variety of Web services as follows. • A computer is required for Web service settings, starting with CANON iMAGE GATEWAY. • For information on countries and regions where CANON iMAGE GATEWAY is available, visit the Canon website (http://canon.com/cig). Registering Web Services First, sign up for a free CANON iMAGE GATEWAY account. CANON iMAGE GATEWAY offers various services, such as the ability to share images in an online photo album. CANON iMAGE GATEWAY also serves as a bridge site to send images wirelessly to e-mail addresses, social networking services, and other Web services. Click http://canon.com/ cig, access the appropriate CANON iMAGE GATEWAY site for your country of residence, and follow the on-screen instructions to register as a member. You can continue to register other Web services other than CANON iMAGE GATEWAY to your account. For further details, check the websites for each web service you want to register. CANON iMAGE GATEWAY In [Camera-linked information], you can check a record of image uploading to Web services, and in [Library], you can view the images uploaded by date.
Page 46 • An Internet connection is required to access CANON iMAGE GATEWAY (an Internet browser must be installed on the computer, you must have an account with an Internet service provider, and an Internet connection must be established). • Check CANON iMAGE GATEWAY for browser (Microsoft Internet Explorer, etc.) settings, conditions and version information when connecting to CANON iMAGE GATEWAY. • Separate ISP connection and access point fees may be applicable. Adjusting Settings for Using Web Services From CANON iMAGE GATEWAY Adjust account settings for the Web services you want to use. Because CameraWindow is used to adjust settings, be sure to install it from the included CD-ROM beforehand. Installation instructions can be found in “Included Software, PDF Manuals” (= 2 7). Connect the camera to a computer with the interface cable. When using a Windows computer, you can connect wirelessly, without using an interface cable, however settings must be completed beforehand (= 5 9). Start CameraWindow.
Page 47 Connecting to Web Services Choose [Set Up Web Services]. Click [Set Up Web Services]. Login to CANON iMAGE GATEWAY. Enter your CANON iMAGE GATEWAY login name and password, and then click [Login]. Set a Web service you want to use. Follow the on-screen instructions to complete settings for Web services you want to use. Once the Web service settings are complete, click [Finish] at the bottom of the window to close it.
Page 48 Choose the name of the Web service you want to set, and click [ ] in the middle of the lists. The name of the Web service that will be saved to the camera will be displayed in the [Camera] list. Click [▲] or [▼] to change the order of the Web services that will be displayed in the camera’s wireless LAN menu. After you inish adjusting settings in the [Camera] list to your liking, close the window. Web service settings will be applied to the camera. • If CameraWindow is not displayed in step 2, see “Using CameraWindow to Transfer Images to a Computer” (= 6 9) for details. • Up to 20 e-mail addresses can be registered to the camera for sending images as e-mail. • After logging in to CANON iMAGE GATEWAY the second time in step 4, the screen in step 6 will be displayed. To change settings for Web services you use, click [Edit Web Services]. • To add or change Web services, repeat the above procedures starting from step 1. Connecting to Web Services Connect to Web services registered to the camera. Access the wireless LAN screen. Press the <o> button.
Page 49 Connect to an access point. Press the <o> buttons or turn the <7> dial to choose [Add an Access Point], and then press the <m> button. A list of detected access points will be displayed in the [Access Point Connect] screen. For further instructions, see “Preparing to Register a Computer” (= 5 6) or “Connecting to Access Points in the List” (= 6 7). For instructions after connecting to an access point, see “Adjusting Settings for Using Web Services From CANON iMAGE GATEWAY” (= 4 6). • You can also conigure this setting through touch-screen operations (= 9 1). • When a connection destination is set using the Touch Actions setting (= 2 48), you can automatically access the function to connect to the last connected destination from the next time by just dragging on the screen without needing to perform the connection operation.
Page 50: Connecting To A Smartphone
Connecting to a Smartphone Add a smartphone with wireless LAN functionality to the list of available devices as follows. Adding a Smartphone Add a smartphone to your list of devices to connect to via wireless LAN. When establishing a wireless connection with a smartphone, you can either use the camera as an access point (Camera Access Point mode) or use another access point. Follow these instructions when using the camera as an access point. When using another access point, see “Connecting to Access Points in the List” (= 6 7). • Before connecting to a camera via wireless LAN, download and install the dedicated CameraWindow (free) application on your smartphone. For details on this application (supported smartphones and included functions), refer to the Canon website. Access the wireless LAN screen. Press the <o> button. Choose a smartphone. Press the <o><q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button.
Page 51 Connecting to a Smartphone Choose [Add a Device]. Press the <o> buttons or turn the <7> dial to choose [Add a Device], and then press the <m> button. Select the camera as the access point. Press the <o> buttons or turn the <7> dial to choose [Set Camera As Access Point], and then press the <m> button. Use the smartphone to connect to the network displayed on the camera screen. Choose the displayed SSID (network name) from the smartphone’s Wi-Fi setting menu. Enter the encryption key displayed on the camera screen into the password ield on the smartphone.
Page 52 Connecting to a Smartphone Start CameraWindow on the smartphone. Once the smartphone is recognized on the camera, the device connection screen will be displayed on the camera. Choose a smartphone to connect to. Choose the smartphone for the connection (either by pressing the <o> buttons or by turning the <7> dial), and then press the <m> button. Adjust the privacy settings. Press the <q><r> buttons or turn the <7> dial to choose [Yes], and then press the <m> button. You can now use the smartphone to receive images sent from the camera, or to geotag images on the camera (= 7 8). When the smartphone has been added successfully, the image transfer screen will be displayed (= 7 5).
Page 53 Connecting to a Smartphone • All camera images can be viewed from the connected smartphone when you choose [Yes] in step 8. To keep camera images private, so that they cannot be viewed from the smartphone, choose [No] in step 8. • The image quality level for movies that can be sent may differ depending on the smartphone. Refer to the instruction manual provided with your smartphone for details. • To add multiple smartphones, repeat the above procedures starting from step 1. • Once a smartphone is added, the smartphone name will be displayed on the screen in step 3. To connect to a smartphone again, simply choose the smartphone name from the list. • To change privacy settings for smartphones added to the list, choose the smartphone whose settings you want to change from [Edit a Device] in step 3, and then choose [View Settings]. • You can also conigure this setting through touch-screen operations (= 9 1). • When a connection destination is set using the Touch Actions setting (= 2 48), you can automatically access the function to connect to the last connected destination from the next time by just dragging on the screen without needing to perform the connection operation.
Page 54: Connecting To Another Camera
Connecting to Another Camera Connect two cameras via wireless LAN and send images between them as follows. Adding a Camera Add a camera to your list of devices to connect to via wireless LAN. • Only Canon-brand cameras equipped with a wireless LAN function can be connected to wirelessly. Even Canon-brand cameras that support Eye-Fi cards cannot be connected to if they do not have a wireless LAN function. You cannot connect to PowerShot SD430 DIGITAL ELPH WIRELESS/ DIGITAL IXUS WIRELESS cameras with this camera. Access the wireless LAN screen. Press the <o> button. Choose a camera. Press the <o><q><r> buttons or turn the <7> dial to choose [4], and then press the <m> button.
Page 55 Connecting to Another Camera Choose [Add a Device]. Press the <o> buttons or turn the <7> dial to choose [Add a Device], and then press the <m> button. Follow steps 1 – 3 on the target camera. Camera connection information will be added when [Start connection on target camera] is displayed on both camera screens. When the target camera has been added successfully, the image transfer screen will be displayed (= 7 5). • To add multiple cameras, repeat the above procedures starting from step 1. • Once a camera is added, the camera name will be displayed on the screen in step 3. To connect to a camera again, simply choose the camera name from the list. • You can also conigure this setting through touch-screen operations (= 9 1). • When a connection destination is set using the Touch Actions setting (= 2 48), you can automatically access the function to connect to the last connected destination from the next time by just dragging on the screen without needing to perform the connection operation.
Page 56: Connecting To A Computer
Connecting to a Computer Conigure camera settings for a wireless computer connection, and then transfer images to the computer wirelessly using the included software CameraWindow as follows. • When connected to a computer, the camera is used to establish the connection and then the computer (included software CameraWindow) is used to transfer images. • For details on the included software, see the Software Guide. Preparing to Register a Computer Prepare to register a computer. Checking the Computer and Wireless LAN Setup The camera can connect to the following computers via wireless LAN. Windows • Windows 7 Service Pack 1 Macintosh • Mac OS X 10.6.8 or later • Windows 7 Starter and Home Basic editions are not supported. • Windows 7 N (European version) and KN (South Korean version) require a separate download and install of Windows Media Feature Pack. For further details, see the following websites. http://go.microsoft.com/fwlink/?LinkId=159730 To use wireless LAN, an access point base unit (wireless LAN router, etc.) connected to a computer is required. Additionally, the included software, CameraWindow must be installed.
Page 57 Connecting to a Computer • Be sure to use a wireless LAN base unit that conforms to standards listed on “Speciications” (= 3 33). • A router is a device that creates a network (LAN) structure for connecting multiple computers. A router that contains an internal wireless function is called a wireless (LAN) router. • This guide will refer to all wireless routers and base stations as “access points”. • When unsure of your computer setup, refer to the user manual provided with the computer. Checking Your Wireless LAN Settings If you are already using a wireless LAN, check the following items and mark each one on the check sheet. • If system administrator status is needed to adjust network settings, contact the system administrator for details. • These settings are very important for network security. Exercise adequate caution when changing these settings. • For instructions on how to check settings, refer to the user guide included with your access point. Check sheet Network name (SSID/ESSID) The SSID or ESSID for the access point you use. ○ None ○ WEP (open system Network certiicate/data encryption authentication) (encryption method/encryption mode) ○ WPA-PSK (TKIP) The method for encrypting data during wireless transmission. ○ WPA-PSK (AES) ○ WPA2-PSK (TKIP) ○ WPA2-PSK (AES) Encryption key (network key)
Page 58 Connecting to a Computer • If you use MAC address iltering on your wireless LAN, be sure to enter the camera’s MAC address to your access point. You can check the MAC address for your camera by choosing the [3] tab, [Wireless LAN Settings], and then [Check MAC Address]. • The different types of security are as follows. - None: Encryption is not used when connecting to an access point. - WEP: A standard of encryption supported by most wireless LAN devices. - WPA-PSK (TKIP): An improved WEP standard that uses TKIP encryption. - WPA-PSK (AES): An improved WEP standard that uses AES encryption. - WPA2-PSK (TKIP): An improved WPA standard that uses TKIP encryption. - WPA2-PSK (AES): An improved WPA standard that uses AES encryption. • AES uses higher security than TKIP. • There is no difference in security levels between WPA and WPA2.
Page 59 Connecting to a Computer Computer Settings for Connecting to a Wireless LAN (Windows only) When using a Windows computer, wireless LAN connection settings on the computer are necessary to connect to a camera wirelessly. Conirm that your computer is connected to a wireless LAN, and then follow each of the next steps. Turning On Media Streaming and Network Discovery If you activate media streaming, the camera will be able to detect and search your computer when they are connected wirelessly. If you activate network discovery, your computer will be able to detect and search the camera. Open the Control Panel window. Click [Control Panel] from the Start menu. Choose [Network and Internet]. Click [Network and Internet]. Choose [Network and Sharing Center]. Click [Network and Sharing Center]. Choose [Change advanced sharing settings]. Click [Change advanced sharing settings]. Choose [Choose media streaming options...]. Click [Choose media streaming options...] for the current proile.
Page 60 Connecting to a Computer Turn on media streaming. Click [Turn on media streaming]. Choose [OK]. Click [OK]. Turn on network discovery. Click [Turn on network discovery] for the current proile. Save the changes. Click [Save changes]. Close the Control Panel window. Enabling ICMP Inbound Echo Requests and UPnP Services Enabling ICMP (Internet Control Message Protocol) will allow you to check the network connection status. Enabling UPnP (Universal Plug & Play) will allow the network to automatically recognize network devices. Open the Control Panel window. Click [Control Panel] from the Start menu. Choose [System and Security]. Click [System and Security].
Page 61 Connecting to a Computer Choose [Windows Firewall]. Click [Windows Firewall]. Choose [Advanced settings]. Click [Advanced settings]. Choose [Inbound Rules]. Click [Inbound Rules]. Enable ICMP inbound echo requests. Choose [File and Printer Sharing] items ending in [ICMPv4], and then click [Enable Rule] on the right side of the window. Turn on UPnP services. Choose [Wireless Portable Devices (UPnP-In)], and then click [Enable Rule] on the right side of the window. Close the [Windows Firewall with Advanced Security] window. Close the Control Panel window. • If [Disable Rule] is displayed in steps 6 – 7, the item is already enabled, and can be left as is.
Page 62 Connecting to a Computer Adding a Computer Add a computer to your list of devices to connect to via wireless LAN. • Be sure to also read the user guide included with your access point. Access the wireless LAN screen. Press the <o> button. Choose a computer. Press the <o><q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button.
Page 63 Connecting to a Computer Choose [Add a Device]. Press the <o> buttons or turn the <7> dial to choose [Add a Device], and then press the <m> button. A list of detected access points will be displayed in the [Access Point Connect] screen. Proceed to either “Connecting to a WPS Supported Access Point” (= 6 4) or “Connecting to Access Points in the List” (= 6 7). To manually choose and connect to an access point, see the supplemental explanation column (= 6 8) in “Connecting to Access Points in the List”. • Once a computer is added, the computer name will be displayed on the screen in step 3. To connect to a computer again, simply choose the computer name from the list. • You can also conigure this setting through touch-screen operations (= 9 1). • When a connection destination is set using the Touch Actions setting (= 2 48), you can automatically access the function to connect to the last connected destination from the next time by just dragging on the screen without needing to perform the connection operation.
Page 64 Connecting to a Computer Connecting to a WPS Supported Access Point WPS (Wi-Fi Protected Setup) is a structure for simplifying settings when connecting one wireless LAN device to another. You can use either Push Button Coniguration Method or PIN Method for settings on a WPS supported device. The push button coniguration method is used in the following explanation. • Refer to the user guide provided with your access point to check if it supports WPS. Choose [WPS Connection]. Press the <o> buttons or turn the <7> dial to choose [WPS Connection], and then press the <m> button. Choose [PBC Method]. Press the <o> buttons or turn the <7> dial to choose [PBC Method], and then press the <m> button.
Page 65 Connecting to a Computer Establish the connection. On the access point, hold down the WPS connection button for a few seconds. On the camera, press the <m> button. The camera will connect to the access point. A list of computers connected to the access point will appear in the [Select a Device] screen. Choose a computer to connect Press the <o> buttons or turn the <7> dial to choose the computer name, and then press the <m> button. When using a Macintosh computer, see “Using CameraWindow to Transfer Images to a Computer” (= 6 9). Install a driver (Windows only). On the computer, click the Start menu and choose [Control Panel]. Click [Add a device].
Page 66 Connecting to a Computer Double click the connected camera icon. Driver installation will begin. After driver installation is complete, and the camera and computer connection is enabled, the AutoPlay screen will be displayed. Nothing will be displayed on the camera screen. Proceed to “Using CameraWindow to Transfer Images to a Computer” (= 6 9). • If you chose [PIN Method] in step 5, a PIN code will be displayed on the screen. Be sure to set this code in the access point. Choose a device in the [Select a Device] screen. For further details, refer to the user guide included with your access point. • To add multiple computers, repeat the above procedures starting from step 1. • When inished adding computers, press the <n> button on the image transmission screen displayed after you connect to a computer in step 7. Choose [OK] after the conirmation message, and then press the <m> button. • You can also conigure this setting through touch-screen operations (= 9 1).
Page 67 Connecting to a Computer Connecting to Access Points in the List Choose an access point. Press the <o> buttons or turn the <7> dial to choose an access point, and then press the <m> button. Enter an encryption key. Press the <m> button to access the keyboard, and then enter the encryption key (= 4 3). Press the <o> buttons or turn the <7> dial to choose [Next], and then press the <m> button. Choose [Auto]. Press the <o> buttons or turn the <7> dial to choose [Auto], and then press the <m> button. A list of other devices connected to the access point will appear in the [Select a Device] screen.
Page 68 Connecting to a Computer Choose a computer to connect Choose the computer to connect to, following steps 7 – 8 on = 6 5. The computer is now added to the list. • Up to 16 access points will be displayed. If no access points are detected, choose [Manual Settings] in step 4 to manually set an access point. Follow on-screen instructions and enter an SSID, security settings, and an encryption key. • [***] is displayed for the encryption key in step 5 when the same access point is used to connect to another device. To use the same encryption key, choose [Next] (either press the <q><r> buttons or turn the <7> dial) and press the <m> button. • To add multiple computers, repeat the above procedures starting from step 1. • You can also conigure this setting through touch-screen operations (= 9 1).
Page 69 Connecting to a Computer Using CameraWindow to Transfer Images to a Computer Use the computer (included software CameraWindow) to transfer images from the camera to the computer. • For details on how to use CameraWindow, see the Software Guide (= 2 7). Start CameraWindow Windows Click [Downloads Images From Canon Camera using Canon CameraWindow]. CameraWindow will be displayed. Proceed to “Importing Untransferred Images to a Computer” (= 7 0) or “Choosing Images to Import” (= 7 1). Macintosh CameraWindow will be automatically displayed when a wireless connection is established between the camera and computer. • If CameraWindow is not displayed when using a Macintosh computer, click the CameraWindow icon in the Dock.
Page 70 Connecting to a Computer Importing Untransferred Images to a Computer Import images to a computer that have not yet been transferred. Import untransferred images. Click [Import Images from Camera]. Click [Import Untransferred Images]. Images that have not yet been transferred to a computer will be imported. Click [OK] in the screen that is displayed after image import is complete. • CameraWindow default settings will save images to the Pictures or My Pictures folders on a computer. For details on how to change the destination folders for saved images, see the Software Guide (= 2 7). • If you click [Import All Images], all images on the camera will be imported. • Movies will take longer to import since the ile size is larger than still images. • To disconnect from the camera, turn off the camera.
Page 71 Connecting to a Computer Choosing Images to Import Choose whichever images you like to import to a computer. Display the image import screen. Click [Import Images from Camera]. Click [Select Images to Import]. Choose an image. Click images you want to import. The background of selected images will turn blue. Click [ ] to deselect the images, and the background will turn gray. Import images. Click [ ] (import). The selected images will be imported to the computer. Click [OK] in the screen that is displayed after image import is complete. • CameraWindow default settings will save images to the Pictures or My Pictures folders on a computer. For details on how to change the destination folders for saved images, see the Software Guide (= 2 7). • Movies will take longer to import since the ile size is larger than still images. • To disconnect from the camera, turn off the camera.
Page 72: Connecting To A Printer
Connecting to a Printer Add a wireless printer to the list of available devices as follows. Adding a Printer Add a printer to your list of devices to connect to via wireless LAN. When establishing a wireless connection with a printer, you can either use the camera as an access point (Camera Access Point mode) or use another access point. • Follow these instructions when using the camera as an access point. When using another access point, see “Connecting to Access Points in the List” (= 6 7) in “Adding a Computer”. Access the wireless LAN screen. Press the <o> button. Choose a printer. Press the <o><q><r> buttons or turn the <7> dial to choose [2], and then press the <m> button.
Page 73 Connecting to a Printer Choose [Add a Device]. Press the <o> buttons or turn the <7> dial to choose [Add a Device], and then press the <m> button. Select the camera as the access point. Press the <o> buttons or turn the <7> dial to choose [Set Camera As Access Point], and then press the <m> button. Use the printer to connect to the network displayed on the camera screen. Choose the displayed SSID (network name) from the printer’s Wi-Fi setting menu.
Page 74 Connecting to a Printer Choose the printer. Once the printer is ready for the connection, press the <m> button when the printer name is displayed on the camera. When the printer has been added successfully, the printing screen will be displayed. Choose an image to print. Choose an image to print (either by pressing the <q><r> buttons or by turning the <7> dial), and then press the <m> button to access the printing screen. Press the <o> buttons or turn the <7> dial to choose [Print], and then press the <m> button. Printing now begins. For detailed printing instructions, see = 2 86. • Once a printer is added, the printer name will be displayed on the screen in step 3. To connect to a printer again, simply choose the printer name from the list. • When a connection destination is set using the Touch Actions setting (= 2 48), you can automatically access the function to connect to the last connected destination from the next time by just dragging on the screen without needing to perform the connection operation.
Page 75: Sending Images
Sending Images Send images wirelessly to destinations registered on the camera as follows. • Images can be uploaded to social networking services or sent to email addresses, via CANON iMAGE GATEWAY. See CANON iMAGE GATEWAY for details. • You can send up to 50 images together with one send operation. You can send movies together as long as the total playback time is within 2 minutes. However, if the destination is a Web service, the number of movies and images that can be sent may be less depending on the Web service. See the desired Web service for details. • Depending on the condition of the network you are using, it may take a long time to send movies. Be sure to keep an eye on the camera battery level. • When connected to a computer, images are transferred using the computer (included software CameraWindow) instead of the camera (= 6 9). Sending Images Individually Choose an image. Turn the <7> dial to choose an image to send. Send the image. Press the <q><r> buttons to choose [Send this image], and then press the <m> button. When uploading to YouTube, read the terms of service, choose [I Agree], and press the <m> button. Image transfer will begin. After images are uploaded to a Web service, [OK] is displayed. Press the <m> button to return to the playback screen.
Page 76: Sending Multiple Images
Sending Images • To disconnect from the camera, press the <n> button, and after the conirmation message, choose [OK] (either press the <q><r> buttons or turn the <7> dial) and press the <m> button. • On the screen, wireless signal strength is indicated by the following icons. ] high, [ ] medium, [ ] low, [ ] weak However, no icon is displayed when the camera is used as an access point. • You can also send images by touching [Send this image]. Choosing the Image Resolution (Size) On the screen described on = 7 5, you can choose the resolution (size) of images to send by pressing the <o> buttons. • To send images at original size, select [No] as the resizing option. • Choosing [ ] or [ ] will resize images that are larger than the selected size before sending. • Movies cannot be resized. Sending Multiple Images Choose [Select and send]. Press the <q><r> buttons to choose [Select and send], and then press the <m> button.
Page 77 Sending Images Choose images. Press the <o><q><r> buttons to choose an image to send, and then press the <m> button. [ ] is displayed. To cancel selection, press the <m> button again. [ ] is no longer displayed. Repeat this process to choose additional images. After you inish choosing images, press the <n> button. Send the images. Press the <q><r> buttons or turn the <7> dial to choose [Send], and then press the <m> button (= 7 5). • You can also choose images in step 2 by pressing the zoom lever twice toward <k> to access single-image display and then pressing the <q><r> buttons or turning the <7> dial. • In step 3, you can choose the resolution (size) to resize images to before sending (= 7 6). • You can also access the screen in step 2 by touching [Select and send] in step 1, and send images by touching [Send] in step 3. • You can also choose images by touching them on the screen in step 2. Touching [ ] will display the screen in step 3.
Page 78: Geotagging Images On The Camera
Geotagging Images on the Camera GPS data recorded on a smartphone using the dedicated CameraWindow application (= 5 0) can be added to images on the camera. Images are tagged with information including the latitude, longitude, and elevation. • Before shooting, make sure the date and time and your home time zone are set correctly. (See “Setting the Date and Time” (= 1 8).) Additionally, in [Time Zone] (= 2 64), specify any shooting destinations that are in other time zones. • The smartphone you will use for geotagging must be authorized to view the images on the camera (= 5 2). • Others may be able to locate or identify you by using location data in your geotagged still images or movies. Be careful when sharing these images with others, as when posting images online where many others can view them. Other Information Edit or erase wireless LAN settings as follows. Editing Connection Information Edit connection information saved to the camera. You can change device nicknames (display names) that are displayed on the camera, and erase connection information.
Page 79 Other Information Choose a device to edit. Press the <o><q><r> buttons or turn the <7> dial to choose the icon of the device to edit, and then press the <m> button. Choose [Edit a Device]. Press the <o> buttons or turn the <7> dial to choose [Edit a Device], and then press the <m> button. Choose a device to edit. Press the <o> buttons or turn the <7> dial to choose the device to edit, and then press the <m> button.
Page 80 Other Information Choose an option to edit. Press the <o> buttons or turn the <7> dial to choose an option to edit, and then press the <m> button. For instructions on erasing connection information or changing nicknames, see “Erasing Connection Information” and later sections, below. • Editable items differ depending on the device or destination. Web services • Erase connection information (access points) • Change nickname that is displayed on the camera Smartphones • Change privacy settings for images • Erase connection information Another camera/ • Change nickname that is displayed on the camera computer/ • Erase connection information printer • Connection information refers to information on how the camera connects to another device or destination. • You can also conigure this setting through touch-screen operations (= 9 1). Erasing Connection Information Choose [Select & Delete Connection Info]. Press the <o> buttons or turn the <7> dial to choose [Select & Delete Connection Info], and then press the <m> button. When the target device is a camera, press the <o> buttons or turn the <7> dial to choose [Erase All Connection Info], and then press the <m> button.
Page 81 Other Information Choose the connection info to delete. Press the <o> buttons or turn the <7> dial to choose the connection information to erase, and then press the <m> button. When [Erase (connection information)?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The selected connection information will be erased. The display reverts to the screen in step • When you erase all connection information from a target device, it is no longer listed, and the display reverts to the screen in step 4. • When you erase all target devices, the display reverts to the screen in step 3. • To erase all connection information for a device at once, choose [Erase All Connection Info] in step 6. • You can also conigure this setting through touch-screen operations (= 9 1).
Page 82 Other Information Changing a Device Nickname You can change the device nickname (display name) that is displayed on the camera. Change the nickname. Choose [Change Device Nickname]. Select the input ield and press the <m> button. Use the keyboard displayed to enter a new nickname (= 4 3). The camera will return to the display in step 4 and the new nickname will be displayed. • You can also conigure this setting through touch-screen operations (= 9 1). Returning the Wireless LAN Settings to Default Return the wireless LAN settings to default if you transfer ownership of the camera to another person, or dispose of it. Access the menu. Press the <n> button. Choose [Wireless LAN Settings]. Move the zoom lever to choose the [3] tab. Press the <o> buttons or turn the <7> dial to choose [Wireless LAN Settings], and then press the <m> button.
Page 83 Other Information Choose [Reset Settings]. Press the <o> buttons or turn the <7> dial to choose [Reset Settings], and then press the <m> button. When the [Reset Settings] screen is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. Wireless LAN settings will be reset to defaults, and the camera will return to initial screen for this setting. • When returning the wireless LAN settings to defaults, all Web services set using a computer will also be erased from the camera. Be sure to conirm that you want to reset all wireless LAN settings before using this option. • To reset other settings (aside from wireless LAN) to defaults, choose [Reset All] in the [3] tab. • You can also conigure this setting through touch-screen operations (= 9 1).
Page 85: Advanced Guide
Advanced Guide Camera Basics Practical guide that introduces other camera basics and describes shooting and playback options...
Page 86: On/Off
On/Off Shooting Mode Press the power button to turn the camera on and prepare for shooting. To turn the camera off, press the power button again. Playback Mode Press the <1> button to turn the camera on and view your shots. To turn the camera off, press the <1> button again. • To switch to Playback mode from Shooting mode, press the <1> button. • To switch to Shooting mode from Playback mode, press the shutter button halfway (= 8 7). • The lens will be retracted after about one minute, once the camera is in Playback mode, and the lash will be lowered if it was up. You can turn the camera off when the lens is retracted by pressing the <1> button. Power-Saving Features (Auto Power Down) As a way to conserve battery power, the camera automatically deactivates the screen (Display Off) and then turns itself off after a speciic period of inactivity. Power Saving in Shooting Mode The screen is automatically deactivated after about one minute of inactivity. In about two more minutes, the lens is retracted and the camera turns itself off. To activate the screen and prepare for shooting when the screen is off but the lens is still out, press the shutter button halfway (= 8 7). Power Saving in Playback Mode The camera turns itself off automatically after about ive minutes of inactivity.
Page 87: Shutter Button
Shutter Button To ensure your shots are in focus, always press the shutter button lightly (halfway) initially. Once the subject is in focus, press the button all the way down to shoot. In this manual, shutter button operations are described as pressing the button halfway or all the way down. Press halfway. (Press lightly to focus.) Press the shutter button halfway. The camera beeps twice, and AF frames are displayed around image areas in focus. Press all the way down. (From the halfway position, press fully to shoot.) The camera shoots, as a shutter sound is played. Keep the camera still until the shutter sound ends. • Images may be out of focus if you shoot without initially pressing the shutter button halfway. • Length of shutter sound playback varies depending on the time required for the shot. It may take longer in some shooting scenes, and images will be blurry if you move the camera (or the subject moves) before the shutter sound ends.
Page 88: Shooting Modes
Shooting Modes Use the mode dial to access each shooting mode. P, Tv, Av, M, and C Modes Take a variety of shots using your preferred settings (= 1 65, 201). Auto Mode Fully automatic shooting, with camera-determined settings (= 9 6). Movie Mode For shooting movies (= 1 61). Movie Digest Mode You can also shoot movies You can make a short movie of a day when the mode dial is not set to Movie mode, simply by just by shooting still images (= 1 36). pressing the movie button. Scene Mode Shoot with optimal settings for speciic scenes (= 1 37). Creative Filters Mode Add a variety of effects to images when shooting (= 1 42).
Page 89: Func. Menu
FUNC. Menu Conigure commonly used shooting functions through the FUNC. menu as follows. Note that menu items and options vary depending on the shooting mode (= 3 20 – 323). Access the FUNC. menu. Press the <m> button. Choose a menu item. Press the <o> buttons to choose a menu item. Available options are shown at the bottom of the screen. Options Menu Items Choose an option. Press the <q><r> buttons or turn the <7> dial to choose an option. Options labeled with a [ ] icon can be conigured by pressing the <n> button. Finish the setup process. Press the <m> button. The screen before you pressed the <m> button in step 1 is displayed again, showing the option you conigured. • To undo any accidental setting changes, you can restore the camera’s default settings (= 2 76).
Page 90 FUNC. Menu Using Touch-Screen Operations to Conigure Settings Access the FUNC. menu by pressing the <m> button, and then either drag the menu up or down to scroll it, or touch an item to choose it. Touch an option to choose it. Touch the option again to conirm your choice, and then press the <m> button to return to the previous screen. Options You can access the screen for options Menu Items labeled with a [ ] icon by touching...
Page 91: Menu Menu
MENU Menu Conigure a variety of camera functions through other menus as follows. Menu items are grouped by purpose on tabs, such as shooting [4], playback [ 1 ], and so on. Note that available settings vary depending on the selected shooting or playback mode (= 3 24 – 330). Access the menu. Press the <n> button. Choose a tab. Move the zoom lever to choose a tab. After you have pressed the <o> buttons to choose a tab initially, you can switch between tabs by pressing the <q><r> buttons. Choose a setting. Press the <o> buttons or turn the <7> dial to choose a setting. To choose settings with options not shown, irst press the <m> or <r> button to switch screens, and then either press the <o> buttons or turn the <7> dial to select the setting. To return to the previous screen, press the <n> button.
Page 92 MENU Menu Choose an option. Press the <q><r> buttons to choose an option. Finish the setup process. Press the <n> button to return to the screen displayed before you pressed the <n> button in step 1. • To undo any accidental setting changes, you can restore the camera’s default settings (= 2 76). Touch-Screen Operations To access tabs, press the <n> button to access the menu, and then touch the desired tab. Drag the settings up or down to scroll them, or touch a setting to choose it. Touch an option to choose it. Settings shown with [q][r] icons on either side can also be conigured by touching these icons. For options displayed with a bar to indicate the level, touch the desired position on the bar. To conigure settings for which options are not shown, irst touch the setting to access the setting screen. On the setting screen, either drag or touch to choose the setting item, and then touch to choose the option. To return to the previous screen, touch [ You can also touch input elements (such as check boxes or text ields) to select them, and you can enter text by touching the on-screen keyboard. When [ ] is shown, you can touch [ ] instead of pressing the <m> button, if you prefer. When [ ] is shown, you can touch [ ] instead of pressing the <n> button, if you prefer. To dismiss the menu, press the <n> button again.
Page 93: Indicator Display
Indicator Display The indicator of the camera (= 5 ) lights up or blinks depending on the camera status. Indicator Indicator Color Camera Status Status Connected to a computer (= 3 1), or display off (= 8 6, 271) Indicator Green Starting up, recording/reading/transmitting (on back) Blinking images, or shooting long exposures (= 2 02, 204) Wireless LAN connection established Indicator Blue Wireless LAN connection or data transfer in (on top) Blinking progress • When the indicator blinks green, never turn the camera off, open the memory card/battery cover, or shake or jolt the camera, which may corrupt images or damage the camera or memory card.
Page 95: Smart Auto Mode
Smart Auto Mode Convenient mode for easy shots with greater control over shooting...
Page 96: Shooting (Smart Auto)
Still Images Movies Shooting (Smart Auto) For fully automatic selection at optimal settings for speciic scenes, simply let the camera determine the subject and shooting conditions. Turn the camera on. Press the power button. The startup screen is displayed. Enter <A> mode. Set the mode dial to <A>. Aim the camera at the subject. The camera will make a slight clicking noise as it determines the scene. Icons representing the scene and image stabilization mode are displayed in the upper right of the screen (= 1 01, 103). Frames displayed around any detected subjects indicate that they are in focus. Compose the shot. To zoom in and enlarge the subject, move the zoom lever toward (telephoto), and to zoom away from the subject, move it toward <j> (wide angle). (A zoom bar Zoom Bar showing the zoom position is displayed.) Focus Range (approx.)
Page 97 Shooting (Smart Auto) Shoot. Shooting Still Images Focus. Press the shutter button halfway. The camera beeps twice after focusing, and AF frames are displayed to indicate image areas in focus. Several AF frames are displayed when multiple areas are in focus. The lash automatically rises in low-light conditions. Shoot. Press the shutter button all the way down. As the camera shoots, a shutter sound is played, and in low-light conditions when the lash is up, it ires automatically. Keep the camera still until the shutter sound ends. Your shot is only displayed until the camera is ready to shoot again.
Page 98 Shooting (Smart Auto) Shooting Movies Start shooting. Press the movie button. The camera beeps once as recording begins, and [ Rec] is displayed with the elapsed time. Elapsed Time Black bars displayed on the top and bottom edges of the screen indicate image areas not recorded. Frames displayed around any detected faces indicate that they are in focus. Once recording begins, you can take your inger off the movie button. R esize the subject and recompose the shot as needed. To resize the subject, do the same thing as in step 3 on = 9 6. However, note that the sound of camera operations will be recorded, and movies shot at zoom factors shown in blue will look grainy. When you recompose shots, the focus, brightness, and colors will be automatically adjusted. Finish shooting. Press the movie button again to stop shooting. The camera beeps twice as recording stops. Recording will stop automatically when the memory card becomes full. Still Images/Movies • To restore camera sound if you have accidentally deactivated it (by holding the button down while turning the camera on), press the <n> button and choose [Mute] on the [3] tab, and then press the <q><r> buttons to choose [Off].
Page 99 Shooting (Smart Auto) Still Images • A lashing [ ] icon warns that images are more likely to be blurred by camera shake. In this case, mount the camera on a tripod or take other measures to keep it still. • If your shots are dark despite the lash iring, move closer to the subject. For details on the lash range, see “Speciications” (= 3 33). • The subject may be too close if the camera only beeps once when you press the shutter button halfway. For details on the focusing range (shooting range), see “Speciications” (= 3 33). • To reduce red-eye and to assist in focusing, the lamp may be activated when shooting in low-light conditions. • A blinking [h] icon displayed when you attempt to shoot indicates that shooting is not possible until the lash has inished recharging. Shooting can resume as soon as the lash is ready, so either press the shutter button all the way down and wait, or release it and press it again. • The shutter sound will not be played when the Sleeping and Babies (Sleeping) icons (= 1 01) are displayed. • Restart the camera if the message [Wrong lash position. Restart the camera] displayed, which indicates that your inger or some other object is obstructing the movement of the lash. •...
Page 100 Shooting (Smart Auto) Movies • Keep your ingers away from the Microphone microphone while shooting movies. Blocking the microphone may prevent audio from being recorded or may cause the recording to sound mufled. • Avoid touching camera controls other than the movie button when shooting movies, because sounds made by the camera will be recorded. • To correct suboptimal image color that may occur in [ ] movie shooting (= 1 27) after you recompose shots, press the movie button to stop recording, and then press it again to resume recording. • Audio is recorded in stereo.
Page 101: Scene Icons
Shooting (Smart Auto) Still Images Movies Scene Icons In <A> mode, shooting scenes determined by the camera are indicated by the icon displayed, and corresponding settings are automatically selected for optimal focusing, subject brightness, and color. Depending on the scene, continuous images may be shot (= 1 02). Background Normal Backlit Dark Sunsets Spotlights Subject – People – – – In Motion – – – – Shadows on Face – – – Smiling – – – Sleeping – – –...
Page 102 Shooting (Smart Auto) • When the drive mode is set to [ ] (= 1 79), and when [Hg Lamp Corr.] is set to [On] and scenes are automatically corrected (= 1 26), Smiling, Sleeping, Babies (Smiling), Babies (Sleeping), and Children icons will not be displayed. • If the lash is set to [ ], the Backlit icons for Smiling and Children will not be displayed. • Babies, Babies (Smiling), Babies (Sleeping), and Children icons will be displayed when [Face ID] is set to [On], and the face of a registered baby (under two years old) or child (from two to twelve years old) is detected (= 1 13). Conirm beforehand that the date and time are correct (= 1 8). • Try shooting in <G> mode (= 1 65) if the scene icon does not match actual shooting conditions, or if it is not possible to shoot with your expected effect, color, or brightness. Continuous Shooting Scenes If you shoot a still image when the following icons are displayed, the camera will shoot continuously. If you press the shutter button halfway when one of the icons in the table below is displayed, one of the following icons will be displayed to inform you that the camera will shoot continuous images: [ ], or [W]. : C onsecutive images are captured, and the camera Smiling (including Babies) analyzes details such as facial expressions to save the image determined to be the best.
Page 103: Image Stabilization Icons
Shooting (Smart Auto) Still Images Movies Image Stabilization Icons Optimal image stabilization for the shooting conditions is automatically applied (Intelligent IS). Additionally, the following icons are displayed in <A> mode. Image stabilization for movies, Image stabilization for still reducing strong camera shake, images as when shooting while walking (Dynamic IS) Image stabilization for slow Image stabilization for still camera shake, such as when images, when panning shooting movies at telephoto (Powered IS) No image stabilization, because Image stabilization for macro the camera is mounted on shots (Hybrid IS) a tripod or held still by other means * Displayed when you pan, following moving subjects with the camera. When you follow subjects moving horizontally, image stabilization only counteracts vertical camera shake, and horizontal stabilization stops. Similarly, when you follow subjects moving vertically, image stabilization only counteracts horizontal camera shake. • To cancel image stabilization, set [IS Mode] to [Off] (= 1 99). In this case, an IS icon is not displayed.
Page 104 Shooting (Smart Auto) Still Images Movies On-Screen Frames A variety of frames are displayed once the camera detects subjects you are aiming the camera at. • A white frame is displayed around the subject (or person’s face) determined by the camera to be the main subject, and gray frames are displayed around other detected faces. Frames follow moving subjects within a certain range to keep them in focus. However, if the camera detects subject movement, only the white frame will remain on the screen. • When you are pressing the shutter button halfway and the camera detects subject movement, a blue frame is displayed, and the focus and image brightness are constantly adjusted (Servo AF). • Try shooting in <G> mode (= 1 65) if no frames are displayed, if frames are not displayed around desired subjects, or if frames are displayed on the background or similar areas. • To choose subjects to focus on, touch the desired subject on the screen. ] is displayed, and the camera enters Touch AF mode. Pressing the shutter button halfway will display a blue AF frame, and the camera will keep the subject in focus and image brightness adjusted (Servo AF). • Touch AF is not available when shooting movies.
Page 105: Common, Convenient Features
Common, Convenient Features Still Images Movies Zooming In Closer on Subjects (Digital Zoom) When distant subjects are too far away to enlarge using the optical zoom, use digital zoom for up to about 20x enlargement. Move the zoom lever toward . Hold the lever until zooming stops. Zooming stops at the largest possible zoom factor (before the image becomes Zoom Factor noticeably grainy), which is then indicated on the screen. Move the zoom lever toward again. To continue magnifying the subject, keep zooming. • Moving the zoom lever will display the zoom bar (which indicates the zoom position). The color of the zoom bar will change depending on the zoom range. - White range: optical zoom range where the image will not appear grainy. - Yellow range: digital zoom range where the image is not noticeably grainy (ZoomPlus). - Blue range: digital zoom range where the image will appear grainy. Because the blue range will not be available at some resolution settings (= 1 24) the maximum zoom factor can be achieved by following step 1.
Page 106 Common, Convenient Features Still Images Movies Shooting at Preset Focal Lengths (Step Zoom) You can shoot at preset focal lengths of 24, 28, 35, 50, 85, 100 or 120 mm (35mm ilm equivalent). This is convenient when you want to shoot at the angle of view of those focal lengths. Choose a focal length. To change the focal length from 24 to 28 mm, turn the <y> ring counterclockwise until it clicks. Keep turning the <y> ring to increase the focal length, which changes to 35, 50, 85, 100, and 120 mm at each click. • Step zoom is not available when shooting movies, so turning the <y> ring has no effect. • When you are using digital zoom (= 1 05), you cannot adjust the zoom factor by turning the <y> ring counterclockwise. However, you can set the focal length to 120 mm by turning it clockwise.
Page 107: Using The Self-Timer
Common, Convenient Features Still Images Movies Using the Self-Timer With the self-timer, you can include yourself in group photos or other timed shots. The camera will shoot about 10 seconds after you press the shutter button. Conigure the setting. Press the <m> button, choose [ in the menu, and then choose the []] option (= 8 9). Once the setting is complete, []] is displayed. Shoot. For Still Images: Press the shutter button halfway to focus on the subject, and then press it all the way down. For Movies: Press the movie button. Once you start the self-timer, the lamp will blink and the camera will play a self- timer sound. Two seconds before the shot, the blinking and sound will speed up. (The lamp will remain lit in case the lash ires.) To cancel shooting after you have triggered the self-timer, press the <n> button. To restore the original setting, choose ] in step 1.
Page 108 Common, Convenient Features • You can also cancel shooting after the timer begins by touching [ Still Images Movies Using the Self-Timer to Avoid Camera Shake This option delays shutter release until about two seconds after you have pressed the shutter button. If the camera is unsteady while you are pressing the shutter button, it will not affect your shot. Conigure the setting. Follow step 1 on = 1 07 and choose [[]. Once the setting is complete, [[] is displayed. Follow step 2 on = 1 07 to shoot. Still Images Movies Customizing the Self-Timer You can specify the delay (0 – 30 seconds) and number of shots (1 – 10). Choose [$]. Following step 1 on = 1 07, choose [$] and press the <n> button.
Page 109 Common, Convenient Features Conigure the setting. Turn the <y> ring to choose [Delay], either press the <q><r> buttons or turn the <7> dial to choose [Shots], and then press the <n> button. Once the setting is complete, [$] is displayed. Follow step 2 on = 1 07 to shoot. • For movies shot using the self-timer, [Delay] represents the delay before recording begins, but the [Shots] setting has no effect. • When you specify multiple shots, image brightness and white balance are determined by the irst shot. More time is required between shots when the lash ires or when you have speciied to take many shots. Shooting will stop automatically when the memory card becomes full. • When a delay longer than two seconds is speciied, two seconds before the shot, the lamp blinking and self-timer sound will speed up. (The lamp will remain lit in case the lash ires.) • You can also cancel shooting after the timer begins by touching [...
Page 110 Common, Convenient Features Still Images Shooting By Touching the Screen (Touch Shutter) With this option, instead of pressing the shutter button, you can simply touch the screen and release your inger to shoot. The camera will focus on subjects and adjust image brightness automatically. Prepare to use touch shutter. Press the <n> button, choose [Touch Shutter] on the [4] tab, and then choose [On] (= 9 1). Choose a subject to focus on. Touch the subject on the screen and keep your inger on the screen. The camera beeps twice after focusing. A blue frame is displayed, and the camera will keep the subject in focus and image brightness adjusted (Servo AF). Shoot. Release your inger from the screen. A shutter sound is played as the camera shoots. To cancel touch shutter, choose [Off] in step 1. • Even while the shot is displayed, you can prepare for the next shot by touching [^].
Page 111: Deactivating The Flash
Common, Convenient Features Still Images Deactivating the Flash Prepare the camera for shooting without the lash as follows. Conigure the setting. Press the <r> button, choose [!] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. If the lash is already up, it will be lowered automatically. Once the setting is complete, [!] is displayed. To restore the original setting, repeat this process but choose [ • If a lashing [ ] icon is displayed when you press the shutter button halfway in low-light conditions, mount the camera on a tripod or take other measures to keep it still. • You can also conigure this setting by pressing the <r> button, touching [!], and then touching it again.
Page 112: Adding A Date Stamp
Common, Convenient Features Still Images Adding a Date Stamp The camera can add the shooting date to images, in the lower-right corner. However, note that date stamps cannot be edited or removed, so conirm beforehand that the date and time are correct (= 1 8). Conigure the setting. Press the <n> button, choose [Date Stamp] on the [4] tab, and then choose the desired option (= 9 1). Once the setting is complete, [DATE] is displayed. Shoot. As you take shots, the camera adds the shooting date or time to the lower-right corner of images. To restore the original setting, choose [Off] in step 1. • Date stamps cannot be edited or removed. • Shots taken without adding a date stamp can be printed with one as follows. However, adding a date stamp this way to images that already have one may cause it to be printed twice. - Use the included software to print For details, refer to the Software Guide (= 2 7). - Print using printer functions (= 2 86) - Use camera DPOF print settings (= 2 93) to print...
Page 113: Using Face Id
Using Face ID If you register a person ahead of time, the camera will detect that person’s face, and prioritize focus, brightness, and color for that person when shooting. In <A> mode, the camera can detect babies and children based on registered birthdays and optimize settings for them when shooting. This function is also useful when searching for a speciic registered person among a large number of images (= 2 25). Personal Information • Information such as images of a face (face info) registered with Face ID, and personal information (name, birthday) will be saved on the camera. Additionally, when registered people are detected, their names will be recorded in still images. When using the Face ID function, be careful when sharing the camera or images with others, and when posting images online where many others can view them. • When disposing of a camera or transferring it to another person after using Face ID, be sure to erase all information (registered faces, names, and birthdays) from the camera (= 1 21). Registering Face ID Information You can register information (face info, name, birthday) for up to 12 people to use with Face ID. Access the setting screen. Press the <n> button, choose [Face ID Settings] on the [4] tab, and then press the <m> button (= 9 1). Press the <o> buttons or turn the <7> dial to choose [Add to Registry], and then press the <m> button.
Page 114 Using Face ID Press the <o> buttons or turn the <7> dial to choose [Add a New Face], and then press the <m> button. Register face information. Aim the camera so that the face of the person you want to register is inside the gray frame at the center of the screen. A white frame on the person’s face indicates that the face is recognized. Make sure a white frame is displayed on the face, and then shoot. If the face is not recognized, you cannot register face information. Save the settings. After [Register?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The [Edit Proile] screen is displayed.
Page 115 Using Face ID Enter a name. Press the <m> button. Touch characters on the keyboard to enter them. Up to 10 characters can be used. Press the <n> button to return to the edit proile screen. Enter a birthday. Press the <o> buttons or turn the <7> dial to choose [Birthday], and then press the <m> button. Press the <q><r> buttons to choose a setting. Press the <o> buttons or turn the <7> dial to specify the date. When inished, press the <m> button. Save the settings. Press the <o> buttons or turn the <7> dial to choose [Save], and then press the <m> button. After a message is displayed, press the <q><r> buttons or turn the <7> dial to choose [Yes], and then press the <m> button. Continue registering face information. To register up to 4 more points of face information (expressions or angles), repeat steps 2 – 3. Registered faces are more easily recognized if you add a variety of face information. In addition to a head on angle, add a slight side angle, a shot when smiling, and shots inside and outside.
Page 116 Using Face ID • The lash will not ire when following step 2. • If you do not register a birthday in step 5, Babies or Children icons (= 1 01) will not display in <A> mode. • You can overwrite registered face info, and add face info later if you have not illed all 5 face info slots (= 1 19). • You can also enter a name on the screen in step 4 by pressing the <o><q><r> buttons or turning the <7> dial to select characters, and then pressing the <m> button. Move the cursor by turning the <y> ring, and press the < > button to delete characters, as needed. Shooting If you register a person ahead of time, the camera will prioritize that person as the main subject, and optimize focus, brightness, and color for that person when shooting. When you point the camera toward a subject, the names of up to 3 registered people will be displayed when they are detected. Shoot. Displayed names will be recorded in still images. Even if people are detected, but their names are not displayed, the names (up to 5 people) will be recorded in the image. • People other than those registered may be mistakenly detected as the registered person if they share similar facial features.
Page 117: Checking And Editing Registered Information
Using Face ID • Registered people may not be correctly detected if the captured image or scene differs drastically from the registered face information. • If a registered face is not detected, or not easily detected, overwrite registered information with new face info. Registering face info right before shooting will allow for easier detection of registered faces. • If a person is mistakenly detected as another person and you continue shooting, you can edit or erase the name recorded in the image during playback (= 2 31). • Because faces of babies and children change quickly as they grow, you should update their face info regularly (= 1 19). • Names will still be recorded in images even if you clear the [Shooting Info] check box in [Custom Display] (= 2 10) on the [4] tab so that the names are not displayed. • If you don’t want names to be recorded in still images, choose [Face ID Settings] on the [4] tab, choose [Face ID], and then choose [Off]. • You can check names recorded in images in the playback screen (simple information display) (= 2 16). Checking and Editing Registered Information Checking Registered Face ID Information Access the [Check/Edit Info] screen.
Page 118 Using Face ID Check the registered information. Press the <o> buttons or turn the <7> dial to choose an item, and then press the <m> button. Check the registered information. Changing the Name or Birthday Access the [Edit Proile] screen. Following steps 1 – 3 above, choose [Edit Proile] and press the <m> button. Input changes. Press the <o> buttons or turn the <7> dial to choose an item, and follow steps 4 – 5 on = 1 15 to input changes. • Even if you change names in [Edit Proile], the names recorded in previously shot images will remain the same. • You can use the included software to edit registered names. Some characters entered with the included software may not display on the camera, but will be correctly recorded in images.
Page 119 Using Face ID Overwriting and Adding Face Information You can overwrite existing face information with new face info. You should update face information regularly, especially with babies and children, as their faces change quickly as they grow. You can also add face information when all 5 face info slots have not been illed. Access the [Add Face Info] screen. On the screen in step 1 on = 1 13, choose [Add Face Info] and press the <m> button. Choose the name of the person to overwrite. Press the <o><q><r> buttons or turn the <7> dial to choose the name of a person to overwrite, and then press the <m> button. If 4 or less face information slots are registered, follow step 5 on = 1 20 to add more face info. Access the face info screen. Read the message that displays, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The face info screen is displayed. Choose the face info to overwrite. Press the <o><q><r> buttons or turn the <7> dial to choose the face info to overwrite, and then press the <m> button.
Page 120 Using Face ID Register face information. Follow steps 2 – 3 on = 1 14 to shoot, and then register the new face information. Registered faces are more easily recognized if you add a variety of face information. In addition to a head-on angle, add a slight side angle, a shot when smiling, and shots inside and outside. • You cannot add face information if all 5 information slots are illed. Follow the steps above to overwrite face information. • You can follow the above steps to register new face info when there is at least one slot open, however you cannot overwrite any face information. Instead of overwriting face info, irst erase unwanted existing info (see below), and then register new face information as needed. Erasing Face Information Access the [Check/Edit Info] screen. Following step 1 on = 1 13, choose [Check/Edit Info] and press the <m> button. Choose the name of the person whose face info you want to erase. Press the <o><q><r> buttons or turn the <7> dial to choose the name of the person whose face info you want to erase, and then press the <m> button.
Page 121: Erasing Registered Information
Using Face ID Access the [Face Info List] screen. Press the <o> buttons or turn the <7> dial to choose [Face Info List], and then press the <m> button. Choose the face info to erase. Press the <m> button, press the <o><q><r> buttons or turn the <7> dial to choose the face info you want to erase, and then press the <m> button. After [Erase?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The selected face info will be erased. Erasing Registered Information You can erase information (face info, name, birthday) registered to Face ID. However, names recorded in previously shot images will not be erased. Access the [Erase Info] screen. Follow step 1 on = 1 13 and choose [Erase Info].
Page 122 Using Face ID Choose the name of the person whose info you want to erase. Press the <o><q><r> buttons or turn the <7> dial to choose the name of a person to erase, and then press the <m> button. After [Erase?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. • If you erase a registered person’s info, you will not be able to display their name (= 1 16), overwrite their info (= 2 31), or search images for them (= 2 25). • You can also erase a person’s name only from images (= 2 32).
Page 123: Image Customization Features
Image Customization Features Still Images Changing the Aspect Ratio Change the image aspect ratio (ratio of width to height) as follows. Conigure the setting. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). Once the setting is complete, the screen aspect ratio will be updated. To restore the original setting, repeat this process but choose [ Used for display on widescreen HDTVs or similar display devices. Same aspect ratio as 35mm ilm, used for printing images at 5 x 7-inch or postcard sizes. Native aspect ratio of the camera screen, also used for display on standard- deinition televisions or similar display devices, or for printing images at 3.5 x 5-inch or A-series sizes. Square aspect ratio. Aspect ratio commonly used for portraits.
Page 124 Image Customization Features Still Images Changing Image Resolution (Size) Choose from 4 levels of image resolution, as follows. For guidelines on how many shots at each resolution setting can it on a memory card, see “Speciications” (= 3 33). Conigure the setting. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. To restore the original setting, repeat this process but choose [ Guidelines for Choosing Resolution Based on Paper Size (for 4:3 Images) A2 (16.5 x 23.4 in.) ]: For e-mailing images. A3 – A5 (11.7 x 16.5 – 5.8 x 8.3 in.) 5 x 7 in. Postcard 3.5 x 5 in.
Page 125 Image Customization Features Still Images Red-Eye Correction Red-eye that occurs in the lash photography can be automatically corrected as follows. Access the [Flash Settings] screen. Press the <n> button, choose [Flash Settings] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting. Choose [Red-Eye Corr.], and then choose [On] (= 9 1). Once the setting is complete, [R] is displayed. To restore the original setting, repeat this process but choose [Off]. • Red-eye correction may be applied to image areas other than eyes (if the camera misinterprets red eye makeup as red pupils, for example). • You can also correct existing images (= 2 55). • You can also access the screen in step 2 by pressing the <r> button and then the <n> button. • You can also access the screen in step 2 by pressing the <r> button and then touching [...
Page 126: Correcting Greenish Image Areas From Mercury Lamps
Image Customization Features Still Images Correcting Greenish Image Areas from Mercury Lamps In shots of evening scenes with subjects illuminated by mercury lamps, the subjects or background may appear to have a greenish tinge. This greenish tinge can be corrected automatically when shooting, using Multi-area White Balance. Conigure the setting. Press the <n> button, choose [Hg Lamp Corr.] on the [4] tab, and then choose [On] (= 9 1). Once the setting is complete, [ ] is displayed. To restore the original setting, repeat this process but choose [Off]. • After you are inished shooting under mercury lamps, you should set [Hg Lamp Corr.] back to [Off]. Otherwise, green hues not caused by mercury lamps may be corrected by mistake. • Try taking some test shots irst to make sure you obtain the desired results.
Page 127: Changing Movie Image Quality
Image Customization Features Movies Changing Movie Image Quality 3 image quality settings are available. For guidelines on the maximum movie length at each level of image quality that will it on a memory card, see “Speciications” (= 3 33). Conigure the setting. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. To restore the original setting, repeat this process but choose [ Image Resolution Frame Rate Details Quality 1920 x 1080 24 fps For shooting in Full HD 1280 x 720 30 fps For shooting in HD For shooting in standard 640 x 480 30 fps deinition * Fine Detail Movie Processing (This function quickly processes a large amount of information, making it possible to record even iner details in movies.) •...
Page 128: Using The Wind Filter
Image Customization Features Movies Using the Wind Filter Distorted audio caused by recording when the wind is strong can be reduced. However, the recording may sound unnatural when this option is used when there is no wind. Conigure the setting. Press the <n> button, choose [Wind Filter] on the [4] tab, and then choose [On] (= 9 1). To restore the original setting, repeat this process but choose [Off].
Page 129: Helpful Shooting Features
Helpful Shooting Features Still Images Movies Using the Electronic Level An electronic level can be displayed on the screen when shooting as a guideline to determine if the camera is level. Display the electronic level. Press the button several times to display the electronic level. Level the camera as needed. Level the camera so that the center of the electronic level is green. • If the electronic level is not displayed in step 1, press the <n> button, and on the [4] tab, choose [Custom Display]. Add a [ ] to [ ] or [ ] to choose the electronic level. • Tilting the camera too far forward or backward will prevent you from using the electronic level, which will turn gray. • The electronic level is not displayed during movie recording. • If you hold the camera vertically, the orientation of the electronic level will be updated automatically to match the camera orientation. • If your shots are not level even if you use the electronic level, try calibrating the electronic level (= 2 72).
Page 130: Magnifying The Area In Focus
Helpful Shooting Features Still Images Magnifying the Area in Focus You can check the focus by pressing the shutter button halfway, which will enlarge the portion of the image in focus in the AF frame. Conigure the setting. Press the <n> button, choose [AF- Point Zoom] on the [4] tab, and then choose [On] (= 9 1). Check the focus. Press the shutter button halfway. The face detected as the main subject is now magniied. To restore the original setting, choose [Off] in step 1. • The area in focus will not be magniied when you press the shutter button halfway if a face was not detected, if the person is too close to the camera and their face is too large for the screen, or if the camera detects subject movement. • The area in focus is not magniied while digital zoom is in use (= 1 05) or when a TV is used as a display (= 2 84).
Page 131: Checking For Closed Eyes
Helpful Shooting Features Checking for Closed Eyes ] is displayed when the camera detects that people may have closed their eyes. Conigure the setting. Press the <n> button, choose [Blink Detection] on the [4] tab, and then choose [On] (= 9 1). Shoot. ] is displayed when the camera detects a person whose eyes are closed. To restore the original setting, choose [Off] in step 1. • When you have speciied multiple shots in [$] mode, this function is only available for the inal shot. • ] mode This feature is not available during continuous shooting in [ (= 1 02). • A frame is displayed around people whose eyes are closed when you have selected 2 – 10 seconds in [Review], or if you have selected [Hold] (= 1 33).
Page 132: Customizing Camera Operation
Customizing Camera Operation Customize shooting functions on the [4] tab of the menu as follows. For instructions on menu functions, see “MENU Menu” (= 9 1). Still Images Deactivating the AF Assist Beam You can deactivate the lamp that normally lights up to help you focus when you press the shutter button halfway in low-light conditions. Conigure the setting. Press the <n> button, choose [AF- assist Beam] on the [4] tab, and then choose [Off] (= 9 1). To restore the original setting, repeat this process but choose [On]. Still Images Deactivating the Red-Eye Reduction Lamp You can deactivate the red-eye reduction lamp that lights up to reduce red- eye when the lash is used in low-light shots. Access the [Flash Settings] screen. Press the <n> button, choose [Flash Settings] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting.
Page 133: Changing The Image Display Period After Shots
Customizing Camera Operation Still Images Changing the Image Display Period After Shots Change how long images are displayed after shots as follows. Conigure the setting. Press the <n> button, choose [Review] on the [4] tab, and then choose the desired option (= 9 1). To restore the original setting, repeat this process but choose [Quick]. Displays images only until you can Quick shoot again. Displays images for the speciied time. Even while the shot is 2 – 10 sec. displayed, you can take another shot by pressing the shutter button halfway again. Displays images until you press Hold the shutter button halfway. No image display after shots.
Page 134: Changing The Image Display Style After Shots
Customizing Camera Operation Still Images Changing the Image Display Style After Shots Change the way images are displayed after shots as follows. In [Review], choose either 2 – 10 seconds or [Hold] (= 1 33). Conigure the setting. Press the <n> button, choose [Review Info] on the [4] tab, and then choose the desired option (= 9 1). To restore the original setting, repeat this process but choose [Off]. Displays only the image. Displays shooting details Detailed (= 3 16). Shows the area in the AF frame Focus magniied, enabling you to check Check the focus. Follow the steps in “Checking the Focus” (= 2 22). •...
Page 135: Other Shooting Modes
Other Shooting Modes Shoot more effectively in various scenes, and take shots enhanced with unique image effects or captured using special functions...
Page 136: Auto Clip Recording (Movie Digest)
Still Images Movies Auto Clip Recording (Movie Digest) You can make a short movie of a day just by shooting still images. Before each shot, the camera will automatically record a movie clip of the scene. Each clip recorded that day is combined into a single ile. Enter < > mode. Set the mode dial to < >. Shoot. To shoot a still image, press the shutter button all the way down. Before shooting, the camera will automatically record a clip about 2 – 4 seconds long. • Clips may not be recorded if you shoot a still image immediately after turning the camera on, choosing < > mode, or operating the camera in other ways. • Battery life is shorter in this mode than in <A> mode, because clips are recorded for each shot. • Any sounds from camera operations during movie recording will be included in the movie. • Movies created in < > mode can be viewed by date (= 2 29). • Movies created in < > mode are saved as iFrame movies (= 1 62). •...
Page 137: Speciic Scenes
Speciic Scenes Choose a mode matching the shooting scene, and the camera will automatically conigure the settings for optimal shots. Enter <K> mode. Set the mode dial to <K>. Choose a shooting mode. Press the <m> button, choose [I] in the menu, and then choose a shooting mode (= 8 9). Shoot. Still Images Movies I Shoot portraits (Portrait) Take shots of people with a softening effect. Still Images Shoot evening scenes without using a tripod (Handheld NightScene) Beautiful shots of evening scenes or portraits with evening scenery in the background, without the need to hold the camera very still (as with a tripod). A single image is created by combining consecutive shots, reducing camera shake and image noise.
Page 138 Speciic Scenes Still Images Movies S Shoot under water (Underwater) Natural-colored shots of sea life and underwater scenery, when you use an optional waterproof case (= 2 80). This mode can correct white balance and match the effect of using a commercially available color-compensating ilter (= 1 74). Still Images Movies P Shoot with snowy backgrounds (Snow) Bright, natural-colored shots of people against snowy backgrounds. Still Images Movies t Shoot ireworks (Fireworks) Vivid shots of ireworks.
Page 139 Speciic Scenes • Subjects appear larger in [ ] mode compared to other modes. • In [ ] and [S] modes, shots may look grainy because the ISO speed (= 1 69) is increased to suit the shooting conditions. • Because the camera will shoot continuously in [ ] mode, hold it steady while shooting. • In [ ] mode, excessive camera shake or certain shooting conditions may prevent you from obtaining the desired results. • In [t] mode, mount the camera on a tripod or take other measures to keep it still and prevent camera shake. Additionally, you should set [IS Mode] to [Off] when using a tripod or other means to hold the camera still (= 1 99). • When you use a tripod for evening scenes, shooting in [A] mode instead of [ ] mode will give better results (= 9 6).
Page 140 Speciic Scenes Still Images Shooting With an Underwater Focusing Range If focusing is dificult in [S] mode (= 1 38) with a focus range of [ using a focus range designed for underwater shooting can ensure optimal underwater shots. Conigure the setting. Follow steps 1 – 2 on = 1 37 and choose [S]. Press the <q> button, choose the desired focus range (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. Shoot. Focusing Range Description Underwater Take close-ups of sea life, using the digital zoom for even closer Macro shots. Avoid missing unexpected underwater shooting opportunities 8 Quick when shooting subjects some distance away. Especially effective for moving subjects. f Manual Focus Focus on subjects manually (= 1 82). Refer to “Speciications” (= 3 33) for details on the range of each focus range.
Page 141 Speciic Scenes • You can also conigure this setting by pressing the <q> button, touching the desired focusing range, and then touching it again. Still Images Making Skin Look Smoother (Smooth Skin) You can apply a smoothening effect when shooting images of people. The effect level and color ([Lighter Skin Tone], [Darker Skin Tone]) can be chosen as follows. Choose [ ]. Follow steps 1 – 2 on = 1 37 and choose [ Access the setting screen. Press the button. Conigure the setting. Press the <o> buttons to choose an option. Choose an effect level (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. A preview is shown of how your shot will look with the effect applied. Shoot. • Areas other than people’s skin may be modiied. • Try taking some test shots irst to make sure you obtain the desired results. • The effect will be stronger for the face of the person detected as the main subject. •...
Page 142: Image Effects (Creative Filters)
Image Effects (Creative Filters) Add a variety of effects to images when shooting. Enter < > mode. Set the mode dial to < >. Choose a shooting mode. Press the <m> button, choose [ ] in the menu, and then choose a shooting mode (= 8 9). Shoot. Still Images Movies Shoot in vivid colors (Super Vivid) Shots in rich, vivid colors. Still Images Movies Posterized shots (Poster Effect) Shots that resemble an old poster or illustration. • In [ ] and [ ] modes, try taking some test shots irst, to make sure you obtain the desired results.
Page 143 Image Effects (Creative Filters) Still Images Shooting High-Contrast Scenes (High Dynamic Range) Three consecutive images are captured at different brightness levels each time you shoot, and the camera combines image areas with optimal brightness to create a single image. This mode can reduce the washed-out highlights and loss of detail in shadows that tends to occur in high-contrast shots. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ Hold the camera still. Mount the camera on a tripod or take other measures to keep it still and prevent camera shake. Shoot. When you press the shutter button all the way down, the camera will take three shots and combine them. • Set [IS Mode] to [Off] (= 1 99) in this mode. • Any subject movement will cause images to look blurry. • There will be a delay before you can shoot again, as the camera processes and combines the images.
Page 144 Image Effects (Creative Filters) Adding Color Effects Follow steps 1 – 2 on = 1 42 and choose [ Press the button, choose a color effect (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. Effect Off ― Sepia Sepia tone shots. Black and white shots. Super Vivid Shots in rich, vivid colors. Poster Effect Shots that resemble an old poster or illustration. • You can also conigure this setting by touching [ ] to access the setting screen, touching the desired color effect, and then touching the same item or [ Still Images Movies Shooting with Faded Colors (Nostalgic) This effect makes colors look faded and images look weathered, as in old photographs. Choose from ive effect levels. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [...
Page 145: Shooting With A Fish-Eye Lens Effect
Image Effects (Creative Filters) Choose an effect level. Turn the <y> ring to choose an effect level. A preview is shown of how your shot will look with the effect applied. Shoot. • Try taking some test shots irst, to make sure you obtain the desired results. • Colors will look faded on the shooting screen, but the image aging effect is not shown. Review the image in Playback mode to see the effect (= 2 16). • The image aging effect is not shown in movies. Still Images Shooting with a Fish-Eye Lens Effect (Fish-eye Effect) Shoot with the distorting effect of a ish-eye lens. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ Choose an effect level. Turn the <y> ring to choose an effect level. A preview is shown of how your shot will look with the effect applied. Shoot.
Page 146: Miniature Effect
Image Effects (Creative Filters) Still Images Movies Shots Resembling Miniature Models (Miniature Effect) Creates the effect of a miniature model, by blurring image areas above and below your selected area. You can also make movies that look like scenes in miniature models by choosing the playback speed before the movie is recorded. People and objects in the scene will move quickly during playback. Note that sound is not recorded. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ A white frame is displayed, indicating the image area that will not be blurred. Choose the area to keep in focus. Press the button. Move the zoom lever to resize the frame, and turn the <7> dial to move it. For movies, choose the movie playback speed. Turn the <y> ring to choose the speed. Return to the shooting screen and shoot. Press the <m> button to return to the shooting screen, and then shoot.
Page 147 Image Effects (Creative Filters) Playback Speed and Estimated Playback Time (for One- Minute Clips) Speed Playback Time Approx. 12 sec. Approx. 6 sec. Approx. 3 sec. • The zoom is not available when shooting movies. Be sure to set the zoom before shooting. • Try taking some test shots irst, to make sure you obtain the desired results. • To switch the orientation of the frame to vertical, press the <q><r> buttons in step 2. To return the frame to horizontal orientation, press the <o> buttons. • To move the frame when it is in horizontal orientation, press the <o> buttons, and to move the frame when it is in vertical orientation, press the <q><r> buttons. • Holding the camera vertically will change the orientation of the frame. • ] at an aspect ratio of [ ] and [ ] at an aspect Movie image quality is [ ratio of [ ] (= 1 23). These quality settings cannot be changed. • You can also move the frame by touching or dragging across the screen.
Page 148 Image Effects (Creative Filters) Still Images Shooting with a Toy Camera Effect (Toy Camera Effect) This effect makes images resemble shots from a toy camera by vignetting (darker, blurred image corners) and changing the overall color. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ Choose a color tone. Turn the <y> ring to choose a color tone. A preview is shown of how your shot will look with the effect applied. Shoot. Standard Shots resemble toy camera images. Warm Images have a warmer tone than with [Standard]. Cool Images have a cooler tone than with [Standard]. • Try taking some test shots irst, to make sure you obtain the desired results.
Page 149: Shooting With A Soft Focus Effect
Image Effects (Creative Filters) Still Images Shooting With a Soft Focus Effect This function allows you to shoot images as if a soft focus ilter is attached to the camera. You can adjust the effect level as desired. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ ]. Choose an effect level. Turn the <y> ring to choose an effect level. A preview is shown of how your shot will look with the effect applied. Shoot. • Try taking some test shots irst, to make sure you obtain the desired results.
Page 150: Shooting In Monochrome
Image Effects (Creative Filters) Still Images Movies Shooting in Monochrome Shoot images in black and white, sepia, or blue and white. Choose [ ]. Follow steps 1 – 2 on = 1 42 and choose [ Choose a color tone. Turn the <y> ring to choose a color tone. A preview is shown of how your shot will look with the effect applied. Shoot. Black and white shots. Sepia Sepia tone shots. Blue Blue and white shots.
Page 151 Image Effects (Creative Filters) Still Images Movies Shooting with Color Accent Choose a single image color to keep and change other colors to black and white. Choose [T]. Follow steps 1 – 2 on = 1 42 and choose [T]. Access the setting screen. Press the button. The original image and the Color Accent image are displayed one after another. By default, green is the color that will be kept. Specify the color. Position the center frame over the color to keep, and then press the <q> button. The speciied color is recorded. Specify the range of colors to keep. Recorded Color Press the <o> buttons or turn the <7> dial to adjust the range. To keep only your speciied color, choose a large negative value. To keep colors similar to your speciied color as well, choose a large positive value. Press the <m> button to return to the shooting screen. Shoot. • Using the lash in this mode may cause unexpected results. • In some shooting scenes, images may look grainy and colors may not look as expected.
Page 152: Shooting With Color Swap
Image Effects (Creative Filters) • You can also conigure this setting by touching [ ] to access the setting screen, recording the color to keep by touching the frame when it is illed with the color, and then touching [ Still Images Movies Shooting with Color Swap You can replace one image color with another before shooting. Note that only one color can be replaced. Choose [Y]. Follow steps 1 – 2 on = 1 42 and choose [Y]. Access the setting screen. Press the button. The original image and the Color Swap image are displayed one after another. By default, green will be replaced with gray. Specify the color to replace. Position the center frame over the color to replace, and then press the <q> button. The speciied color is recorded. Specify the new color. Position the center frame over the new color, and then press the <r> button. The speciied color is recorded.
Page 153 Image Effects (Creative Filters) Specify the range of colors to replace. Press the <o> buttons or turn the <7> dial to adjust the range. To replace only your speciied color, choose a large negative value. To replace colors similar to your speciied color as well, choose a large positive value. Press the <m> button to return to the shooting screen. Shoot. • Using the lash in this mode may cause unexpected results. • In some shooting scenes, images may look grainy and colors may not look as expected. • You can also conigure this setting by touching [ ] to access the setting screen, touching in the frame at left to record the color to replace, touching in the frame at right to record the new color, and then touching [...
Page 154: Special Modes For Other Purposes
Special Modes for Other Purposes Still Images Auto Shooting After Face Detection (Smart Shutter) Auto Shooting After Smile Detection The camera shoots automatically after detecting a smile, even without you pressing the shutter button. Choose [ ]. Follow steps 1 – 2 on = 1 37 and choose [ ], and then press the button. Press the <q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button. The camera now enters shooting standby mode, and [Smile Detection on] is displayed. Aim the camera at a person. Each time the camera detects a smile, it will shoot after the lamp lights up. To pause smile detection, press the <q> button. Press the <q> button again to resume detection. • Switch to another mode when you inish shooting, or the camera will continue shooting each time a smile is detected.
Page 155 Special Modes for Other Purposes • You can also choose the shooting mode by choosing [ ] in steps 1 – 2 on = 1 37, touching [ ] to access the setting screen, touching [ ], and then touching the same item or [ Still Images Using the Wink Self-Timer Aim the camera at a person and press the shutter button all the way down. The camera will shoot about two seconds after a wink is detected. Choose [ ]. Follow steps 1 – 2 on = 1 37 and choose [ ], and then press the button. Press the <q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button. Compose the shot and press the shutter button halfway. On the screen, touch the face of the person who will wink to choose it (Touch AF), and then press the shutter button halfway. Make sure a green frame is displayed around the face of the person who will wink. Press the shutter button all the way down. The camera now enters shooting standby mode, and [Wink to take picture] is displayed.
Page 156 Special Modes for Other Purposes Face the camera and wink. The camera will shoot about two seconds after detecting a wink by the person whose face is inside the frame. To cancel shooting after you have triggered the self-timer, press the <n> button. • If the wink is not detected, wink again slowly and deliberately. • Winking may not be detected if eyes are obscured by hair, a hat, or glasses. • Closing and opening both eyes at once will also be detected as a wink. • If winking is not detected, the camera will shoot about 15 seconds later. • To change the number of shots, press the <o> buttons after choosing ] in step 1. [Blink Detection] (= 1 31) is only available for the inal shot. • If no one is in the shooting area when the shutter button is pressed all the way down, the camera will shoot after a person enters the shooting area and winks. • You can also choose the shooting mode by choosing [ ] in steps 1 – 2 on = 1 37, touching [ ] to access the setting screen, touching [ ], and then touching the same item or [...
Page 157 Special Modes for Other Purposes Still Images Using the Face Self-Timer The camera will shoot about two seconds after detecting that the face of another person (such as the photographer) has entered the shooting area (= 1 84). This is useful when including yourself in group photos or similar shots. Choose [ ]. Follow steps 1 – 2 on = 1 37 and choose ], and then press the button. Press the <q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button. Compose the shot and press the shutter button halfway. Make sure a green frame is displayed around the face you focus on and white frames around other faces. Press the shutter button all the way down. The camera now enters shooting standby mode, and [Look straight at camera to start count down] is displayed. The lamp blinks and the self-timer sound is played. Join the subjects in the shooting area and look at the camera. After the camera detects a new face, the lamp blinking and self-timer sound will speed up. (When the lash ires, the lamp will remain lit.) About two seconds later, the camera will shoot. To cancel shooting after you have triggered the self-timer, press the <n> button.
Page 158 Special Modes for Other Purposes • Even if your face is not detected after you join the others in the shooting area, the camera will shoot about 15 seconds later. • To change the number of shots, press the <o> buttons after choosing ] in step 1. [Blink Detection] (= 1 31) is only available for the inal shot. • You can also choose the shooting mode by choosing [ ] in steps 1 – 2 on = 1 37, touching [ ] to access the setting screen, touching [ ], and then touching the same item or [ Still Images High-Speed Continuous Shooting (High-speed Burst HQ) You can shoot a series of shots in rapid succession by holding the shutter button all the way down. For details on the continuous shooting speed, see “Speciications” (= 3 33). HQ: High Quality Choose [ ]. Follow steps 1 – 2 on = 1 37 and choose [ Shoot.
Page 159 Special Modes for Other Purposes Images Displayed During Playback Each set of images shot continuously is managed as a single group, and only the irst image in that group will be displayed. To indicate that the image is part of a group, [ ] is displayed in the upper left of the screen. • If you erase a grouped image (= 2 40), all images in the group are also erased. Be careful when erasing images. • Grouped images can be played back individually and ungrouped (= 2 30). • Protecting (= 2 36) a grouped image will protect all images in the group. • Grouped images can be viewed individually when played back using Image Search (= 2 25) or Smart Shufle (= 2 35). In this case, images are temporarily ungrouped. • Grouped images cannot be sent individually (= 7 5), and Face ID information cannot be edited (= 2 31). They cannot be tagged as favorites (= 2 44), edited (= 2 43 – 255), categorized (= 2 45), assigned as a start-up image (= 2 66), printed (= 2 86), speciied for printing individually (= 2 94), or added to a photobook (= 2 96). To do these things, either view...
Page 160: Shooting Stitch Assist Images
Special Modes for Other Purposes Still Images Shooting Stitch Assist Images Shoot a large subject by taking multiple shots at various positions, and then use the included software (= 2 7) to combine them into a panorama. Choose [x] or [v]. Follow steps 1 – 2 on = 1 37 and choose [x] or [v]. Take the irst shot. The irst shot will determine the exposure and white balance. Take additional shots. Compose the second shot so that it partially overlaps the image area of the irst shot. Minor misalignment of overlapping portions will be corrected automatically when the images are combined. You can take up to 26 shots, the same way you took the second shot. Finish shooting. Press the <m> button. Use the software to combine the images. For instructions on merging images, refer to the Software Guide (= 2 7). • To use AF lock, assign [%] to the <...
Page 161: Shooting Various Movies
Movies Shooting Various Movies Movies Shooting Movies in <E> Mode Enter <E> mode. Set the mode dial to <E>. Black bars displayed on the top and bottom edges of the screen indicate image areas not recorded. Conigure the settings to suit the movie (= 3 18 – 329). Shoot. Press the movie button. To stop movie recording, press the movie button again. Movies Locking or Changing Image Brightness Before Shooting Before shooting, you can lock the exposure or change it in 1/3-stop increments within a range of –3 to +3. Lock the exposure. Press the <o> button to lock the exposure. The exposure shift bar is displayed. To unlock the exposure, press the <o> button again. Adjust the exposure. Turn the <7> dial to adjust the exposure, as you watch the screen. Shoot.
Page 162: Shooting Iframe Movies
Shooting Various Movies Movies Shooting iFrame Movies Shoot movies that can be edited with iFrame-compatible software or devices. You can quickly edit, save, and manage iFrame movies using the included software (= 2 7). Choose [ ]. Set the mode dial to <E>. Press the <m> button, choose [E] in the menu, and then choose [ ] (= 8 9). Black bars displayed on the top and bottom edges of the screen indicate image areas not recorded. Shoot (= 1 61). • The resolution is [ ] (= 1 27) and cannot be changed. • iFrame is a video format developed by Apple. Movies Shooting Super Slow Motion Movies You can shoot fast-moving subjects for playback later in slow motion. Note that sound is not recorded.
Page 163 Shooting Various Movies Shoot (= 1 61). Playback Time Frame Rate Image Quality (For a 30-sec. Clip) Approx. 4 min. 240 fps (320 x 240) Approx. 2 min. 120 fps (640 x 480) • Zooming is not available during recording, even if you move the zoom lever. • Focus, exposure, and color are determined when you press the movie button. • The movie will be played back in slow motion when you follow steps 1 – 3 on = 2 16. • You can change the playback speed of movies shot in [ ] mode by using the included software. For details, refer to the Software Guide (= 2 7).
Page 165: P Mode
P Mode More discerning shots, in your preferred shooting style • Instructions in this chapter apply to the camera with the mode dial set to <G> mode. • <G>: Program AE; AE: Auto Exposure • Before using a function introduced in this chapter in modes other than <G>, make sure the function is available in that mode (= 3 18 – 329).
Page 166: Shooting In Program Ae Mode (
Mode)
Still Images Movies Shooting in Program AE Mode ( Mode) You can customize many function settings to suit your preferred shooting style. Enter <G> mode. Set the mode dial to <G>. Customize the settings as desired (= 1 66 – 199), and then shoot. • If adequate exposure cannot be obtained when you press the shutter button halfway, shutter speeds and aperture values are displayed in orange. To obtain adequate exposure, try adjusting the following settings. - Activate the lash (= 1 93) - Change the ISO speed (= 1 69) • Movies can be recorded in <G> mode as well, by pressing the movie button. However, some FUNC. (= 8 9) and Menu (= 9 1) settings may be automatically adjusted for movie recording. •...
Page 167 Image Brightness (Exposure Compensation) • You can also adjust brightness by pressing the <o> button, and then touching or dragging the bar. • You can also adjust the correction level by touching the right edge of the screen while turning the <y> ring (= 2 09). Still Images Locking Image Brightness/Exposure (AE Lock) Before shooting, you can lock the exposure, or you can specify focus and exposure separately. Lock the exposure. Aim the camera at the subject to shoot with the exposure locked. With the shutter button pressed halfway, press the <o> button. ] is displayed, and the exposure is locked. To unlock AE, release the shutter button and press the <o> button again. In this case, [ ] is no longer displayed. Compose the shot and shoot. After one shot, AE is unlocked and [ ] is no longer displayed. • AE: Auto Exposure • After the exposure is locked, you can adjust the combination of shutter speed and aperture value by turning the <7> dial (Program Shift).
Page 168: Changing The Metering Method
Image Brightness (Exposure Compensation) Still Images Changing the Metering Method Adjust the metering method (how brightness is measured) to suit shooting conditions as follows. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. For typical shooting conditions, including backlit shots. Evaluative Automatically adjusts exposure to match the shooting conditions. Determines the average brightness of light across the entire Center image area, calculated by treating brightness in the central area Weighted Avg. as more important. Metering restricted to within the [ ] (Spot AE Point frame). You can also link the Spot AE Point frame to the AF frame (see Spot below). Still Images Linking the Spot AE Point Frame to the AF Frame Set the metering method to [ ]. Follow the steps above to choose [ Conigure the setting. Press the <n> button, choose [Spot AE Point] on the [4] tab, and then choose [AF Point] (= 9 1). The Spot AE Point frame will now be linked to the movement of the AF frame (= 1 85).
Page 169 Image Brightness (Exposure Compensation) Still Images Changing the ISO Speed Turn the <y> ring to choose the ISO speed. The option you conigured is now displayed. Automatically adjusts the ISO speed to suit the shooting mode and conditions. For shooting outdoors in fair weather. For shooting in cloudy conditions, or at twilight. High For shooting night scenes, or in dark rooms. • To view the automatically set ISO speed when the camera is set to [ press the shutter button halfway. • Although choosing a lower ISO speed may reduce image graininess, there may be a greater risk of subject blurriness in some shooting conditions. • Choosing a higher ISO speed will increase shutter speed, which may reduce subject blurriness and increase the lash range. However, shots may look grainy. • You can also set the ISO speed by pressing the <m> button, choosing [ choosing an option (either by pressing the <q><r> buttons or turning the <7> dial), and then pressing the < m > button. To specify [ ], press the < > button on the setting screen.
Page 170 Image Brightness (Exposure Compensation) Still Images Adjusting the Setting When the camera is set to [ ], maximum ISO speed can be speciied in a range of [ ] – [ ], and sensitivity can be speciied in a range of three levels. Access the setting screen. Press the <n> button, choose [ISO Auto Settings] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting. Choose a menu item to conigure, and then choose the desired option (= 9 1). • You can also access the [ISO Auto Settings] screen when choosing the ISO speed in the FUNC. menu, by pressing the <n> button. Changing the Noise Reduction Level (High ISO NR) You can choose from 3 levels of noise reduction: [Standard], [High], [Low]. This function is especially effective when shooting at high ISO speeds. Choose a noise reduction level. Press the <n> button, choose [High ISO NR] on the [4] tab, and then choose the desired option. •...
Page 171 Image Brightness (Exposure Compensation) Still Images Auto Exposure Bracketing (AEB Mode) Three consecutive images are captured at different exposure levels (standard exposure, underexposure, and then overexposure) each time you shoot. You can adjust the amount of underexposure and overexposure (relative to standard exposure) from –2 to +2 stops in 1/3-stop increments. Choose [ ]. Press the <m> button, choose ] in the menu, and then choose [ (= 8 9). Conigure the setting. Press the <n> button, and then adjust the setting by pressing the <q><r> buttons or turning the <7> dial. • AEB is only available in [!] mode (= 1 11). • Continuous shooting (= 1 79) is not available in this mode. • If exposure compensation is already in use (= 1 66), the value speciied for that function is treated as the standard exposure level for this function. • You can also access the setting screen of step 2 by pressing the <n>...
Page 172 Image Brightness (Exposure Compensation) Still Images Correcting Image Brightness (i-Contrast) Before shooting, excessively bright or dark image areas (such as faces or backgrounds) can be detected and automatically adjusted to the optimal brightness. To avoid washed-out highlights, specify Dynamic Range Correction. To preserve image detail in shadows, specify Shadow Correct. • Under some shooting conditions, correction may be inaccurate or may cause images to appear grainy. • You can also correct existing images (= 2 54). • You can customize camera operation so that turning the <y> ring adjusts DR Correction or Shadow Correct settings (= 2 06). Still Images Dynamic Range Correction (DR Correction) Tone down bright image areas, which might otherwise look washed out, as follows. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 89). Once the setting is complete, [ @ ] is displayed. Available ISO Speed Item Details (= 1 69) ―...
Page 173: Using The Nd Filter
Image Brightness (Exposure Compensation) • ISO speed (= 1 69) will be adjusted to a speed within the supported range if you have speciied a value outside the supported range indicated here. Still Images Shadow Correct Automatically preserve image detail in shadows as follows. Press the <m> button, choose [ ] in the menu, press the <n> button, and choose [ ] (= 8 9). Once the setting is complete, [@] is displayed. Using the ND Filter To shoot at slower shutter speeds and smaller aperture values, use the ND ilter, which reduces light intensity to 1/8 the actual level (equivalent to 3 stops). Press the <m> button, choose ] in the menu, and then choose [ (= 8 9). • Mount the camera on a tripod or take other measures to keep it still and prevent camera shake. Additionally, you should set [IS Mode] to [Off] when using a tripod or other means to hold the camera still (= 1 99).
Page 174: Color And Continuous Shooting
Color and Continuous Shooting Still Images Movies Adjusting White Balance By adjusting white balance (WB), you can make image colors look more natural for the scene you are shooting. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. Automatically sets the optimal white balance for the shooting Auto conditions. Day Light For shooting outdoors in fair weather. Cloudy For shooting in cloudy conditions, in the shade, or at twilight. For shooting under ordinary incandescent (tungsten) lighting Tungsten and similarly colored luorescent lighting. For shooting under warm-white (or similarly colored) or cool- Fluorescent white luorescent lighting. For shooting under daylight luorescent and similarly colored Fluorescent H luorescent lighting. Flash For shooting with the lash. Sets the optimal white balance for shooting underwater. Tones Underwater down blues to produce natural-looking colors overall.
Page 175 Color and Continuous Shooting Still Images Movies Custom White Balance For image colors that look natural under the light in your shot, adjust white balance to suit the light source where you are shooting. Set the white balance under the same light source that will illuminate your shot. Follow the steps on = 1 74 and choose ] or [ Aim the camera at a plain white subject, so that the entire screen is white. Press the < > button. The tint of the screen changes once the white balance data has been recorded. • Colors may look unnatural if you change camera settings after recording white balance data. • You can also record white balance data on the screen above by touching Still Images Movies Manually Correcting White Balance You can correct white balance. This adjustment can match the effect of using a commercially available color temperature conversion ilter or color- compensating ilter. Conigure the setting. Follow the steps on = 1 74 to choose Turn the <y> ring to adjust the correction level for B and A. Once the setting is complete, [ ] is displayed.
Page 176 Color and Continuous Shooting Conigure advanced settings. To conigure more advanced settings, press the <n> button and adjust the correction level by turning the <y> ring or <7> dial or pressing the <o><q><r> buttons. To reset the correction level, press the < > button. Press the <n> button to complete the setting. • The camera will retain white balance correction levels even if you switch to another white balance option (by following steps on = 1 74), but correction levels will be reset if you record custom white balance data. • B: blue; A: amber; M: magenta; G: green • You can customize camera operation so that the B and A adjustment screen can be accessed simply by turning the <y> ring (= 2 06). • One level of blue/amber correction is equivalent to about 7 mireds on a color temperature conversion ilter. (Mired: Color temperature unit representing color temperature conversion ilter density) • You can also choose the correction level by touching or dragging the bar in step 1 or the frame in step 2. • You can also access the screen in step 2 by touching [ ] in step 1. • On the screen in step 2, you can touch [ ] to restore the original level and touch [ ] to return to the shooting screen.
Page 177 Color and Continuous Shooting Still Images Movies Changing Image Color Tones (My Colors) Change image color tones as desired, such as converting images to sepia or black and white. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. My Colors Off ― Emphasizes contrast and color saturation, making images Vivid sharper. Tones down contrast and color saturation for subdued Neutral images. Sepia Creates sepia tone images. Creates black and white images. Combines the effects of Vivid Blue, Vivid Green, and Positive Film Vivid Red to produce intense yet natural-looking colors resembling images on positive ilm. Lighter Skin Tone Lightens skin tones. Darker Skin Tone Darkens skin tones. Emphasizes blues in images. Makes the sky, ocean, and Vivid Blue other blue subjects more vivid.
Page 178 Color and Continuous Shooting • White balance (= 1 74) cannot be set in [ ] or [ ] modes. • With [ ] and [ ] modes, colors other than people’s skin tone may be modiied. These settings may not produce the expected results with some skin tones. Still Images Movies Custom Color Choose the desired level of image contrast, sharpness, color saturation, red, green, blue, and skin tones in a range of 1 – 5. Access the setting screen. Follow the steps on = 1 77 to choose ], and then press the <n> button. Conigure the setting. Press the <o> buttons to choose an option, and then specify the value by pressing the <q><r> buttons or turning the <7> dial. For stronger/more intense effects (or darker skin tones), adjust the value to the right, and for weaker/lighter effects (or lighter skin tones), adjust the value to the left. Press the <n> button to complete the setting. • You can also specify a value by touching or dragging the bar.
Page 179: Continuous Shooting
Color and Continuous Shooting Still Images Continuous Shooting Hold the shutter button all the way down to shoot continuously. For details on the continuous shooting speed, see “Speciications” (= 3 33). Conigure the setting. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). The option you conigured is now displayed. Shoot. Hold the shutter button all the way down to shoot continuously. Mode Description Continuous shooting, with the focus and exposure determined W Continuous when you press the shutter button halfway. Continuous Continuous shooting and focusing. Shooting AF [AF Frame] is set to [1-point] and cannot be changed. Continuous shooting, with the focus ixed at the position Continuous determined in manual focusing. In [t] mode, focus is determined Shooting LV by the irst shot. * In [t] mode (= 1 38), AF lock (= 1 91), or manual focus mode (= 1 82), [ ] is changed to [ * For details on the continuous shooting speed in each mode, see “Speciications”...
Page 180 Color and Continuous Shooting • Cannot be used with the self-timer (= 1 07) or [Blink Detection] (= 1 31). • Shooting may stop momentarily or continuous shooting may slow down depending on shooting conditions, camera settings, and the zoom position. • As more shots are taken, shooting may slow down. • Shooting may slow down if the lash ires. • With Touch Shutter (= 1 10), the camera will only take one shot instead of shooting continuously. • If you use Face ID (= 1 13) in [W], the name recorded in the image will be ixed to the location where it is displayed in the irst shot. Even if the subject moves, the name will stay ixed in the same position for any subsequent shots.
Page 181: Shooting Range And Focusing
Shooting Range and Focusing Still Images Shooting Close-ups (Macro) To restrict the focus to subjects at close range, set the camera to [e]. For details on the focusing range, see “Speciications” (= 3 33). Press the <q> button, choose [e] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. Once the setting is complete, [e] is displayed. • If the lash ires, vignetting may occur. • With the AF frame mode set to [Face AiAF], using Touch Shutter returns the camera to [ • To prevent camera shake, try mounting the camera on a tripod and shooting with the camera set to [[] (= 1 08). • You can also conigure this setting by pressing the <q> button, touching [e], and then touching it again.
Page 182: Shooting In Manual Focus Mode
Shooting Range and Focusing Still Images Movies Shooting in Manual Focus Mode When focusing is not possible in AF mode, use manual focus. You can specify the general focal position and then press the shutter button halfway to have the camera determine the optimal focal position near the position you speciied. For details on the focusing range, see “Speciications” (= 3 33). Choose [ Press the <q> button, choose [ (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. ] and the MF indicator are displayed. Specify the general focal position. Referring to the on-screen MF indicator bar (which shows the distance and focal position) and the magniied display area, press the <o> buttons or turn the <7> dial to specify the general focal position, and then press the <m> button. MF Indicator Fine-tune the focus. Press the shutter button halfway to have the camera ine-tune the focal position (Safety MF). • AF frame mode or size cannot be changed while focusing manually (= 1 84). If you want to change the AF frame mode or size, cancel manual focus mode irst.
Page 183 Shooting Range and Focusing • You can also adjust the focus by turning the <y> ring (= 2 06). • To focus more accurately, try attaching the camera to a tripod to stabilize it. • To hide the magniied display area, press the <n> button and set [MF- Point Zoom] on the [4] tab to [Off] (= 9 1). • To deactivate automatic focus ine-tuning when the shutter button is pressed halfway, press the <n> button and set [Safety MF] on the [4] tab to [Off] (= 9 1). Still Images Movies Digital Tele-Converter The focal length of the lens can be increased by approximately 1.5x or 2.0x. This can reduce camera shake because the shutter speed is faster than it would be if you zoomed (including using digital zoom) in to the same zoom factor. Press the <n> button, choose [Digital Zoom] on the [4] tab, and then choose the desired option (= 9 1). The view is enlarged and the zoom factor is displayed on the screen. • The digital tele-converter cannot be used with digital zoom (= 1 05) and AF-point zoom (= 1 30). •...
Page 184: Changing The Af Frame Mode
Shooting Range and Focusing Still Images Movies Changing the AF Frame Mode Change the AF (auto focus) frame mode to suit the shooting conditions as follows. Press the <n> button, choose [AF Frame] on the [4] tab, and then choose the desired option (= 9 1). Still Images Movies Face AiAF • Detects people’s faces, and then sets the focus, exposure (evaluative metering only), and white balance ([ ] only). • After you aim the camera at the subject, a white frame is displayed around the person’s face determined by the camera to be the main subject, and up to two gray frames are displayed around other detected faces. • When the camera detects movement, frames will follow moving subjects, within a certain range. • After you press the shutter button halfway, up to nine green frames are displayed around faces in focus. • If faces are not detected, or when only gray frames are displayed (without a white frame), up to nine green frames are displayed in the areas in focus when you press the shutter button halfway. • If faces are not detected when Servo AF (= 1 87) is set to [On], the AF frame is displayed in the center of the screen when you press the shutter button halfway.
Page 185 Shooting Range and Focusing Still Images Movies 1-point One AF frame is displayed. Effective for reliable focusing. • A yellow AF frame is displayed with [ ] if the camera cannot focus when you press the shutter button halfway. Note that AF- point zooming (= 1 30) is not possible. • To compose shots so that subjects are positioned at the edge or in a corner, irst aim the camera to capture the subject in an AF frame, and then hold the shutter button halfway down. As you continue to hold the shutter button halfway, recompose the shot as desired, and then press the shutter button all the way down (Focus Lock). Still Images Moving and Resizing AF Frames (1-point) When you want to change the position or size of the AF frame, set the AF frame mode to [1-point]. Move the AF frame. Touch the screen. An AF frame is displayed in orange where you touched (Touch AF). You can turn the <7> dial to move the AF frame and press the <o><q><r> buttons to ine-tune the position. To return the AF frame to the original position in the center, press the <n> button. Resize the AF frame. To reduce the AF frame size, turn the <y> ring. Turn it again to restore it to the original size. Finish the setup process. Press the <m> button.
Page 186 Shooting Range and Focusing • AF frames are displayed at normal size when you use the digital zoom (= 1 05) or digital tele-converter (= 1 83), and in manual focus mode (= 1 82). • You can also link the Spot AE Point frame to the AF frame (= 1 68). • You can also conigure the AF frame size by pressing the <n> button and choosing [AF Frame Size] on the [4] tab. • On the screen in step 2, you can also move the AF frame by touching the screen, restore the AF frame to the original position by touching [ ], or exit the setting by touching [...
Page 187 Shooting Range and Focusing Still Images Shooting with Servo AF This mode helps avoid missing shots of subjects in motion, because the camera continues to focus on the subject and adjust the exposure as long as you press the shutter button halfway. Conigure the setting. Press the <n> button, choose [Servo AF] on the [4] tab, and then choose [On] (= 9 1). Focus. The focus and exposure are maintained where the blue AF frame is displayed while you are pressing the shutter button halfway. • Focusing may not be possible in some shooting conditions. • In low-light conditions, Servo AF may not be activated (AF frames may not turn blue) when you press the shutter button halfway. In this case, the focus and exposure are set according to the speciied AF frame mode. • If adequate exposure cannot be obtained, shutter speeds and aperture values are displayed in orange. Release the shutter button, and then press it halfway again. • AF lock shooting is not available. • [AF-Point Zoom] on the [4] tab is not available. • Not available when using the self-timer (= 1 07).
Page 188: Changing The Focus Setting
Shooting Range and Focusing Still Images Changing the Focus Setting You can change default camera operation of constantly focusing on subjects it is aimed at, even when the shutter button is not pressed. Instead, you can limit camera focusing to the moment you press the shutter button halfway. Press the <n> button, choose [Continuous AF] on the [4] tab, and then choose [Off] (= 9 1). Helps avoid missing sudden photo opportunities, because the camera constantly focuses on subjects until you press the shutter button halfway. Conserves battery power, because the camera does not focus constantly. Still Images Movies Choosing Subjects to Focus On (Touch AF) You can shoot after choosing a person’s face or another subject to focus on. Set the AF frame to [Face AiAF] (= 1 84). Choose a person’s face or another subject to focus on. Touch the subject or person on the screen.
Page 189 Shooting Range and Focusing When the subject is detected, the camera beeps and [ ] is displayed. The camera will continue to track the subject, even if it moves. To cancel Touch AF, touch [^]. Shoot. Press the shutter button halfway. After the camera focuses, [ ] changes to a green [ Press the shutter button all the way down to shoot. • If you prefer the camera not to shoot when you touch the screen, make sure [Touch Shutter] mode is deactivated. Press the <n> button, and on the [4] tab, select [Touch Shutter: Off] (= 1 10). • Tracking may not be possible when subjects are too small or move too rapidly, or when there is inadequate contrast between subjects and the background. • Even if you are shooting in [e] mode (= 1 81), the camera will revert to [ ] mode if you touch the screen to specify where to focus. • If [Face ID] is set to [On], names will not display when registered people are detected, but the names will be recorded in the still images (= 1 13). However, a name will display if the subject chosen to focus on is the same as a person detected with Face ID.
Page 190 Shooting Range and Focusing Still Images Choosing a Person to Focus On (Face Select) You can shoot after choosing a speciic person’s face to focus on. Prepare the camera for Face Select. Set the AF frame to [Face AiAF] (= 1 84). Assign [ ] to the < > button (= 2 11). Enter Face Select mode. Aim the camera at the person’s face and press the < > button. After [Face Select : On] is displayed, a face frame [ ] is displayed around the face detected as the main subject. Even if the subject moves, the face frame ] follows the subject within a certain range. Choose the face to focus on. To switch the face frame [ ] to another detected face, press the < > button. After you have switched the face frame to all detected faces, [Face Select : Off] is displayed, and the speciied AF frame mode screen is displayed again.
Page 191: Shooting With The Af Lock
Shooting Range and Focusing Still Images Movies Shooting with the AF Lock The focus can be locked. After you lock the focus, the focal position will not change even when you release your inger from the shutter button. Lock the focus. With the shutter button pressed halfway, press the <q> button. The focus is now locked, and [ ] is displayed. To unlock the focus, hold the shutter button halfway down and press the <q> button again. Compose the shot and shoot. • Cannot be used with Touch Shutter (= 1 10) or Touch AF (= 1 88). Still Images Focus Bracketing (Focus-BKT Mode) Three consecutive images are captured each time you shoot, with the irst one at the focal distance you set manually and the others at farther and nearer focal positions determined by presets. The distance from your speciied focus can be set in three levels. Choose [ ]. Press the <m> button, choose [ ] in the menu, and then choose [ (= 8 9).
Page 192 Shooting Range and Focusing Conigure the setting. Press the <n> button, and then adjust the setting by pressing the <q><r> buttons or turning the <7> dial. • Focus bracketing is only available in [!] mode (= 1 11). • Continuous shooting (= 1 79) is not available in this mode. • You can also access the setting screen in step 2 by choosing [ ] in step 1 on = 1 82 and pressing the <n> button. • Three shots are taken, regardless of any quantity speciied in [$] (= 1 08). • In [Blink Detection] mode (= 1 31), this function is only available for the inal shot. • To access the screen in step 2, you can either touch [ ] on the screen in step 1 or touch [ ] on the manual focus screen (= 1 82). •...
Page 193: Flash
Flash Still Images Activating Flash You can have the lash ire for each shot. For details on the lash range, see “Speciications” (= 3 33). Conigure the setting. Press the <r> button, choose [h] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. If the lash is down, it will be raised automatically. Once the setting is complete, [h] is displayed. • You can also conigure this setting by pressing the <r> button, touching [h], and then touching it again.
Page 194: Shooting With Slow Synchro
Flash Still Images Shooting with Slow Synchro With this option, the lash ires to increase the brightness of the main subject (such as people) while the camera shoots at a slow shutter speed to increase the brightness of the background that is out of the lash range. For details on the lash range, see “Speciications” (= 3 33). Conigure the setting. Press the <r> button, choose [Z] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. If the lash is down, it will be raised automatically. Once the setting is complete, [Z] is displayed. Shoot. Even after the lash ires, ensure that the main subject does not move until the shutter sound is inished playing. • Mount the camera on a tripod or take other measures to keep it still and prevent camera shake. Additionally, you should set [IS Mode] to [Off] when using a tripod or other means to hold the camera still (= 1 99). • You can also conigure this setting by pressing the <r> button, touching [Z], and then touching it again.
Page 195: Adjusting The Flash Exposure Compensation
Flash Still Images Adjusting the Flash Exposure Compensation Just as with regular exposure compensation (= 1 66), you can adjust the lash exposure from –2 to +2 stops, in 1/3-stop increments. Press the <r> button and immediately turn the <y> ring to choose the compensation level, and then press the <m> button. Once the setting is complete, [X] is displayed. • When there is a risk of overexposure, the camera automatically adjusts the shutter speed or aperture value during the lash shots to reduce washed- out highlights and shoot at optimal exposure. However, you can deactivate automatic adjustment of the shutter speed and aperture value by accessing <n> (= 9 1) and setting [Safety FE] in [Flash Settings] on the [4] tab to [Off]. • You can also conigure the lash exposure compensation by accessing <n> (= 9 1) and choosing [Flash Exp. Comp] in [Flash Settings] on the [4] tab. • You can also access the [Flash Settings] <n> screen by pressing the <r> button and then the <n> button. • You can also access the [Flash Settings] <n> screen by pressing the <r> button and touching [...
Page 196: Shooting With The Fe Lock
Flash Still Images Shooting with the FE Lock Just as with the AE lock (= 1 67), you can lock the exposure for the lash shots. Set the lash to [h] (= 1 93). Lock the lash exposure. Aim the camera at the subject to shoot with the exposure locked. With the shutter button pressed halfway, press the <o> button. The lash ires, and when [ ] is displayed, the lash output level is retained. To unlock FE, release the shutter button and press the <o> button again. In this case, [ ] is no longer displayed. Compose the shot and shoot. After one shot, FE is unlocked and [ ] is no longer displayed. • FE Lock cannot be used with Touch Shutter (= 1 10) or Touch AF (= 1 88), because touching the screen will cancel FE Lock. •...
Page 197: Changing The Flash Timing
Flash Still Images Changing the Flash Timing Change the timing of the lash and shutter release as follows. Access the setting screen. Press the <n> button, choose [Flash Settings] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting. Choose [Shutter Sync.], and then choose the desired option (= 9 1). The lash ires immediately after 1st-curtain the shutter opens. The lash ires immediately before 2nd-curtain the shutter closes.
Page 198: Shooting Raw Images
Still Images Shooting RAW Images RAW images are “raw” (unprocessed) data, recorded with essentially no loss of image quality from the camera’s internal image processing. Use the Digital Photo Professional (= 2 7) to adjust RAW images as desired with minimal loss of image quality. Press the <m> button, choose [ ] in the menu, and choose the desired option (= 8 9). Records JPEG images. JPEG images are processed in the camera for optimal image quality and compressed to reduce ile size. However, the compression process is irreversible, and images cannot be restored to their original, unprocessed state. Image processing may also cause some loss of image quality. Records RAW images. RAW images are “raw” (unprocessed) data, recorded with essentially no loss of image quality from the camera’s image processing. The data cannot be used in this state for viewing or printing on a computer. You must irst use the included software (Digital Photo Professional) to convert images to ordinary JPEG or TIFF iles. Images can be adjusted with minimal loss of image quality. For details on resolution and the number of shots that will it on a card, see “Speciications” (= 3 33). Records two images, both a RAW image and a JPEG image, for each shot. The JPEG image can be printed or viewed on a computer without using the included software. • When transferring RAW images (or RAW and JPEG images recorded together) to a computer, always use the included software (= 2 7). •...
Page 199: Other Settings
Other Settings Still Images Changing the Compression Ratio (Image Quality) Choose from two compression ratios, as follows: [ ] (Super Fine), ] (Fine). For guidelines on how many shots at each compression ratio can it on a memory card, see “Speciications” (= 3 33). Conigure the setting. Press the <m> button, choose [ ] in the menu, press the <n> button, and choose the desired option (= 8 9). Still Images Movies Changing the IS Mode Settings Conigure the setting. Press the <n> button, choose [IS Mode] on the [4] tab, and then choose the desired option (= 9 1). Optimal image stabilization for the Continuous shooting conditions is automatically applied (Intelligent IS) (= 1 03).
Page 201: Tv, Av, M, And C Mode
Tv, Av, M, and C Mode Take smarter, more sophisticated shots, and customize the camera for your shooting style • Instructions in this chapter apply to the camera as set to the respective mode.
Page 202: Speciic Shutter Speeds ( Mode)
Still Images Speciic Shutter Speeds (<Tv> Mode) Set your preferred shutter speed before shooting as follows. The camera automatically adjusts the aperture value to suit your shutter speed. For details on available shutter speeds, see “Speciications” (= 3 33). Enter <M> mode. Set the mode dial to <M>. Set the shutter speed. Turn the <y> ring to set the shutter speed. • With shutter speeds of 1.3 seconds or slower, there will be a delay before you can shoot again, as images are processed to remove noise. • When shooting at low shutter speeds on a tripod, you should set [IS Mode] to [Off] (= 1 99). • The speed you set may be lowered automatically as needed if the lash ires. • With shutter speeds of 1.3 seconds or slower, ISO speed is [ and cannot be changed. • Orange display of aperture values when you press the shutter button halfway indicates that the settings deviate from standard exposure. Adjust the shutter speed until the aperture value is displayed in white, or use safety shift (= 2 03). •...
Page 203: Speciic Aperture Values ( Mode)
Still Images Speciic Aperture Values (<Av> Mode) Set your preferred aperture value before shooting as follows. The camera automatically adjusts the shutter speed to suit your aperture value. For details on available aperture values, see “Speciications” (= 3 33). Enter mode. Set the mode dial to . Set the aperture value. Turn the <y> ring to set the aperture value. • Orange display of shutter speeds when you press the shutter button halfway indicates that the settings deviate from standard exposure. Adjust the aperture value until the shutter speed is displayed in white, or use safety shift (see below). • : Aperture value (size of the opening made by the iris in the lens) • To avoid exposure problems in <M> and modes, you can have the camera automatically adjust the shutter speed or aperture value, even when standard exposure cannot otherwise be obtained. Press the <n> button and set [Safety Shift] on the [4] tab to [On] (= 9 1). However, safety shift is disabled when the lash ires. • You can customize camera operation so that turning the <7> dial changes the aperture value (= 2 06).
Page 204: Speciic Shutter Speeds And Aperture Values ( Mode)
Still Images Speciic Shutter Speeds and Aperture Values (<M> Mode) Follow these steps before shooting to set your preferred shutter speed and aperture value to obtain the desired exposure. For details on available shutter speeds and aperture values, see “Speciications” (= 3 33). Enter <D> mode. Set the mode dial to <D>. Conigure the setting. Turn the <7> dial to set the shutter speed, and turn the <y> ring to set the aperture value. An exposure level mark based on your Aperture Value speciied value is shown on the exposure Shutter Speed level indicator for comparison to the Standard standard exposure level. Exposure Level The exposure level mark is shown Exposure Level in orange when the difference from Mark standard exposure exceeds 2 stops. “–2” Exposure Level or “+2” is displayed in orange in the lower Indicator right when you press the shutter button halfway. •...
Page 205: Adjusting The Flash Output
Speciic Shutter Speeds and Aperture Values (<M> Mode) • <D>: Manual • Calculation of standard exposure is based on the speciied metering method (= 1 68). • You can customize camera operation so that turning the <y> ring adjusts the shutter speed and turning the <7> dial adjusts the aperture value (= 2 06). Still Images Adjusting the Flash Output Choose from the three lash levels in <D> mode. Enter <D> mode. Set the mode dial to <D>. Conigure the setting. Press the <r> button and immediately turn the <y> ring to choose the lash level, and then press the <m> button. Once the setting is complete, [ X ] is displayed. • You can also set the lash level by choosing [ X ] in the FUNC. menu (= 8 9), or by accessing <n> (= 9 1) and choosing [Flash Output] in [Flash Settings] on the [4] tab.
Page 206: Customization For Shooting Styles
Customization for Shooting Styles Still Images Movies Changing Control Ring Settings Reassign control ring functions as follows. Using the control ring is an enjoyable way to control the camera as you would a fully manual camera. Choose a function to assign to the <y> ring. Press the < > button. Choose an option, either by pressing the < > or <q><r> buttons or by turning the <y> ring or <7> dial. Press the <m> button to complete the setting. Conigure the function to assign. Turn the <y> ring or the <7> dial to conigure the assigned function. • You can also conigure this setting by pressing the < > button, touching an option to choose it, and then touching it again.
Page 207 Customization for Shooting Styles Functions Assignable to the Control Ring Functions you can assign to the control ring vary depending on shooting mode, and those assignments determine which functions you can assign to the control dial. Shooting Mode Assignable Function – – – Tv, Av – +/– +/– +/– – Manual focusing is possible (= 1 82). White balance can be corrected (= 1 74). Step zooming is possible (= 1 06). i-Contrast can be set (= 1 72). The aspect ratio can be changed (= 1 23). – Functions can be assigned as desired (= 2 08). • Av: aperture value (= 2 03); Tv: shutter speed (= 2 02);...
Page 208 Customization for Shooting Styles Still Images Movies Assigning Functions to the Control Ring Assign functions to the control ring based on each shooting mode. Choose [ ]. Following step 1 on = 2 06, choose [ and press the <n> button. Conigure the setting. Press the <q><r> buttons or turn the <7> dial to choose the shooting mode with functions to assign. Press the <o> buttons or turn the <y> ring to choose a function to assign to the control ring. Functions You Can Assign to Functions you can assign to the control the Control Ring dial will be updated automatically. Press the <n> button to return to the shooting screen. • You can also access the setting screen by choosing [ ] in step 1 on = 2 06 and then touching [ • On the setting screen, you can also switch the control ring functions by touching the functions and then [...
Page 209 Customization for Shooting Styles Still Images Switching Control Ring Functions While Coniguring Settings As you touch the screen to switch between the functions you are coniguring, you can turn the control ring to specify ISO speed, exposure compensation, shutter speed, and aperture value immediately. After touching the right edge of the screen (inside the frame shown at left) to view settings, you can drag up or down to choose an item and turn the <y> ring to specify a value. Available setting items vary by shooting mode. Note that the functions assigned to the control ring (= 2 06) are not displayed. +/– +/– +/– • +/–: exposure compensation (= 1 66); ISO: ISO speed (= 1 69); Tv: shutter speed (= 2 02); Av: aperture value (= 2 03)
Page 210: Customizing Display Information
Customization for Shooting Styles Still Images Movies Customizing Display Information Customize what information is shown in various display modes (switched by pressing the button), and whether or not the information is shown on the LCD monitor or viewinder. Access the setting screen. Press the <n> button, choose [Custom Display] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting. Press the <o><q><r> buttons or turn the <7> dial to choose an item, and then press the <m> button. Items you choose for display are labeled with [ Selected items (labeled with a [ ]) will be included in display. Shooting Info Displays shooting information (= 3 14). Grid Lines Displays a reference grid. Electronic Level Displays the electronic level (= 1 29). Displays a histogram (= 2 19), in <G>, <M>, , and <D> Histogram modes.
Page 211 Customization for Shooting Styles Still Images Movies Assigning Functions to the < > Button Access the setting screen. Press the <n> button, choose [Set button] on the [4] tab, and then press the <m> button (= 9 1). Conigure the setting. Press the <o><q><r> buttons or turn the <7> dial to choose a function to assign, and then press the <m> button. Use the assigned function as needed. Press the < > button to activate the assigned function. • To restore default settings, choose [ • Icons labeled with [ ] indicate that the function is not available in the current shooting mode or under current function conditions. • With [ ], you can move and resize the AF frame by pressing the < > button in [1-point] AF frame mode (= 1 85). •...
Page 212: Saving Shooting Settings
Customization for Shooting Styles Still Images Saving Shooting Settings Save commonly used shooting modes and your conigured function settings for reuse. To access saved settings later, simply turn the mode dial to < >. Even settings that are usually cleared when you switch shooting modes or turn the camera off (such as self-timer settings) can be retained this way. Settings that can be saved • Shooting modes ( <G>, <M>, , and <D>) • Items set in <G>, <M>, , or <D> modes (= 1 66 – 204) • Shooting menu settings • Zoom positions • Manual focus positions (= 1 82) • My Menu settings (= 2 13) Enter a shooting mode with settings you want to save, and change the settings as desired. Conigure the setting. Press the <n> button, choose [Save Settings] on the [4] tab, and then press the <m> button. Save the settings. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 213 Customization for Shooting Styles • To edit saved settings (except their shooting mode), choose < >, change the settings, and then repeat steps 2 – 3. These setting details are not applied in other shooting modes. • To clear information you have saved to < > and restore default values, turn the mode dial to < > and choose [Reset All] (= 2 76). Still Images Movies Saving Commonly Used Shooting Menus (My Menu) Save up to ive commonly used shooting menus as menus on the [ ] tab, for instant access to all of these items from a single screen. Access the setting screen. Press the <n> button, choose [My Menu settings] on the [ ] tab, and then press the <m> button (= 9 1). Conigure the setting. Press the <o> buttons or turn the <7> dial to choose [Select items], and then press the <m> button. Press the <o> buttons or turn the <7> dial to choose menus to save (up to ive), and then press the <m> button.
Page 214 Customization for Shooting Styles Rearrange the menu list order, as needed. Press the <o> buttons or turn the <7> dial to choose [Sort], and then press the <m> button. Press the <o> buttons or turn the <7> dial to choose a menu to move, and then press the <m> button. Press the <o> buttons or turn the <7> dial to change the order, and then press the <m> button. Press the <n> button. • Grayed-out items in step 2 can also be speciied, but they may not be available in some shooting modes. • To make My Menu immediately accessible by pressing the <n> button in Shooting mode, choose [Set default view] and press the <q><r> buttons to choose [Yes]. • On the [Select items] screen for saving or clearing items, you can also touch items to select them. • On the [Sort] screen, you can also drag items to change the display order.
Page 215: Playback Mode
Playback Mode Have fun reviewing your shots, and browse or edit them in many ways • To prepare the camera for these operations, press the <1> button to enter Playback mode. • It may not be possible to play back or edit images that were renamed or already edited on a computer, or images from other cameras.
Page 216: Viewing
Still Images Movies Viewing After shooting images or movies, you can view them on the screen as follows. Enter Playback mode. Press the <1> button. Your last shot is displayed. Choose an image. To view the previous image, press the <q> button or turn the <7> dial counterclockwise. To view the next image, press the <r> button or turn the <7> dial clockwise. Press and hold the <q><r> buttons to browse through images quickly. To access Scroll Display mode, turn the <7> dial rapidly. In this mode, turn the <7> dial to browse through images. To return to single-image display, press the <m> button. To browse images grouped by shooting date, press the <o> buttons in Scroll Display mode. Movies are identiied by a [ ] icon. To play movies, go to step 3.
Page 217 Viewing Play movies. To start playback, press the <m> button to access the movie control panel, choose [ ] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button again. Adjust the volume. Volume Press the <o> buttons to adjust the volume. Pause playback. To pause or resume playback, press the <m> button. After the movie is inished, [ ] is displayed. • To switch to Shooting mode from Playback mode, press the shutter button halfway. • To deactivate Scroll Display, press the <n> button, choose [Scroll Display] on the [ 1 ] tab, and then choose [Off]. • If you prefer to have the most recent shot displayed when you enter Playback mode, press the <n> button, and on the [ 1 ] tab, choose [Resume] and then [Last shot]. • To change the transition shown between images, press the <n> button, choose [Transition] on the [ 1 ] tab, and then press the <q><r> buttons to choose the effect. Touch-Screen Operations To view the next image, drag left across the screen, and to view the previous image, drag right.
Page 218 Viewing To access Scroll Display mode, quickly drag left or right repeatedly. You can also choose images in Scroll Display mode by dragging left or right. Touching the central image will restore single-image display. To browse images grouped by shooting date in Scroll Display mode, scroll up or down. To start playback, touch [ ] in step 3 on = 2 17. To adjust the volume during movie playback, quickly drag up or down across the screen. To stop playback, touch the screen. The screen shown at left is displayed, and the following operations are available. Touch [ ] to display the volume panel, and then touch [o][p] to adjust the volume. At a volume of 0, [ ] is displayed. To switch frames, touch the scrollbar or drag left or right. To resume playback, touch [ Touch [^] to return to the screen in step 2 on = 2 16.
Page 219: Switching Display Modes
Viewing Still Images Movies Switching Display Modes Press the button to view other information on the screen, or to hide the information. For details on the information displayed, see = 3 14. No Information Simple Information Detailed Enables you to check the focus Display Display Information (= 2 22)* Display *Not shown for movies. • Switching display modes by pressing the button is also possible immediately after you shoot, while your shot is displayed. However, simple information display is not available. To change the initial display mode, press the <n> button and choose [Review Info] on the [4] tab (= 1 34). • Switching display modes is not possible while the camera is wirelessly connected to devices other than printers. Still Images Movies Overexposure Warning (for Image Highlights) Washed-out highlights in the image lash on the screen in detailed information display.
Page 220 Viewing Still Images Movies RGB Histogram, GPS Information Display Switch between the RGB histogram (still images only) and GPS information display by pressing the <o> button in detailed information display. The RGB histogram shows the distribution of shades of red, green, and blue in an image. The horizontal axis represents R, G, or B brightness, and the vertical axis, how much of the image is at that level of brightness. Viewing this histogram enables you to check image color characteristics. Using a smartphone connected wirelessly to the camera, you can geotag images on the camera, adding information such as latitude, longitude, and elevation (= 7 8). You can review this information in the GPS information display. Latitude, longitude, elevation, and UTC (shooting date and time) are listed from top to bottom. • GPS information display is not available for images that lack this information. • UTC: Coordinated Universal Time, essentially the same as Greenwich Mean Time...
Page 221 Viewing Movies Viewing Movie Digest Clips View movie clips recorded automatically in [ ] mode (= 1 36) on a day of still image shooting as follows. Choose an image. Still images shot in [ ] mode are labeled with an [ ] icon. Choose a still image labeled with [ and press the <m> button. Play the clip. After [Play back movie?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The movie clip recorded automatically on the day of still image shooting is played back, from the beginning. • Movies created in [ ] mode can also be viewed by date (= 2 29). • After a moment, [ ] will no longer be displayed when you are using the camera with information display deactivated (= 2 19). •...
Page 222: Checking The Focus
Viewing Still Images Checking People Detected in Face ID If you switch the camera to simple information display mode (= 2 19), the names of up to ive detected people registered in Face ID (= 1 13) will be displayed. Switch to simple information display mode and check. Press the button repeatedly until simple information display is activated, and then press the <q><r> buttons to choose an image. Names will be displayed on detected people. • If you do not want names to display on images shot using Face ID, press the <n> button, choose [Face ID Info] on the [ 1 ] tab, and then set [Name Display] to [Off]. Still Images Checking the Focus To check the focus of your shots, you can magnify the area of the image that was in the AF frame at the time of shooting. Access Focus Check. Press the button (= 2 19). A white frame is displayed where the AF frame was when the focus was set.
Page 223 Viewing Switch frames. Move the zoom lever toward <k> once. The screen at left is displayed. To switch to a different frame when there are multiple frames, press the <m> button. Zoom in or out, or view other image areas. As you examine the focus, use the zoom lever to zoom in or out. Press the <o><q><r> buttons to adjust the display position. Press the <n> button to restore the original display in step 1. • You can also access the screen in step 2 by touching the lower-right image in step 1. • To adjust the display position, drag across the image in the lower right of the screen in step 2. You can switch between frames by touching [ ] on the screen, or you can return to step 1 by touching [...
Page 224: Browsing And Filtering Images
Browsing and Filtering Images Still Images Movies Navigating Through Images in an Index By displaying multiple images in an index, you can quickly ind the images you are looking for. Display images in an index. Move the zoom lever toward <g> to display images in an index. Moving the lever again will increase the number of images shown. To display fewer images, move the zoom lever toward <k>. Fewer images are shown each time you move the lever. Choose an image. Turn the <7> dial to scroll through the images. Press the <o><q><r> buttons to choose an image. An orange frame is displayed around the selected image. Press the <m> button to view the selected image in single-image display. Touch-Screen Operations Pinch in to switch from single-image display to index display. To view more thumbnails per screen, pinch in again. Drag up or down on the screen to scroll through displayed images.
Page 225 Browsing and Filtering Images To view fewer thumbnails per screen, spread your ingers apart. Touch an image to choose it, and touch it again to view it in single-image display. Still Images Movies Finding Images Matching Speciied Conditions Find desired images quickly on a memory card full of images by iltering image display or jumping between images according to your speciied conditions. You can also protect (= 2 36) or delete (= 2 40) these images all at once. Favorites Displays images tagged as favorites (= 2 44). Shot Date Displays the images shot on a speciic date. Displays the images of a speciic category ; My Category (= 2 45). Displays still images, movies, or movies shot in Still image/Movie ] mode (= 1 36). Name Displays images of a registered person (= 1 13).
Page 226 Browsing and Filtering Images Choose the irst condition for image display or navigation. Press the <o> buttons to choose a display ilter. When [ ] is selected, you can view only images matching this condition by pressing the <q><r> buttons. To perform an action for all of these images together, press the <m> button and go to step 4. Choose the second condition and check the images found. Press the <q><r> buttons to choose another condition. Once you turn the <7> dial, you can view the images narrowed down by your conditions. To cancel this mode, press the <n> button. To switch to iltered image display, press the <m> button and go to step 4. View the iltered images. Images matching your conditions are displayed in yellow frames. To view only these images, press the <q><r> buttons, or turn the <7> dial. To exit iltered image display, press the <o> button, and after [Image search canceled] is displayed, press the <m> button. • When the camera has found no corresponding images for some conditions, those conditions will not be available.
Page 227 Browsing and Filtering Images • Options for viewing the images found (in step 4) include “Navigating Through Images in an Index” (= 2 24), “Viewing Slideshows” (= 2 34), and “Magnifying Images” (= 2 33). You can protect, erase, or print all images found or add them to a photobook by choosing [Select All Images in Search] in “Protecting Images” (= 2 36), “Erasing All Images” (= 2 41), “Adding Images to the Print List (DPOF)” (= 2 93), or “Adding Images to a Photobook” (= 2 96). • However, if you recategorize images (= 2 45) or edit them and save them as new images (= 2 51 – 256), a message is displayed and iltered image display ends. •...
Page 228: Using The Control Ring To Jump
Browsing and Filtering Images • You can also view images that include a speciic person by touching the person in step 2 and then touching the person again. Still Images Movies Using the Control Ring to Jump Use the control ring to ind and jump between desired images quickly by iltering image display according to your speciied conditions. Jump to Favorites Displays images tagged as favorites (= 2 44). Jumps to the irst image in each group of images that Jump Shot Date were shot on the same date. Jump 10 Images Jumps by 10 images at a time. Jump 100 Images Jumps by 100 images at a time. Choose a condition. Choose a condition (or jump method) in single-image display by turning the <y> ring and then pressing the <o> buttons. View images matching your speciied condition, or jump by the speciied amount. Turn the <y> ring to view only images matching the condition or jump by the speciied number of images forward or back. • Turning the <y> ring when browsing images in index display will jump to the previous or next image according to the jump method chosen in single-image display. However, if you have chosen [ ] or [...
Page 229 Browsing and Filtering Images Touch-Screen Operations You can also jump to the previous or next image according to your jump method chosen in step 1 on = 2 28 by dragging left or right with two ingers. Movies Viewing Movie Digest Movies Movies created in [ ] mode (= 1 36) can be viewed by date. Choose a movie. Press the <n> button, choose [Movie Digest Playback] on the [ 1 ] tab, and then choose the date. Play the movie. Press the <m> button to start playback. • You can also start movie playback in step 1 by touching a desired date.
Page 230: Viewing Individual Images In A Group
Browsing and Filtering Images Still Images Viewing Individual Images in a Group Grouped images shot in [ ] mode (= 1 58) are generally displayed together, but they can also be viewed individually. Choose an image group. Press the <q><r> buttons or turn the <7> dial to choose an image labeled ], and then press the <m> button. View individual images in the group. Pressing the <q><r> buttons or turning the <7> dial will display only images in the group. Pressing the <o> button will display [Display all images]. Press <m> to cancel group playback. • During group playback (step 2), you can browse through images quickly “Navigating Through Images in an Index” (= 2 24) and magnify them “Magnifying Images” (= 2 33). You can protect, erase, or print all images in a group at once or add them to a photobook by choosing [All Images in Group] in “Protecting Images” (= 2 36), “Erasing All Images” (= 2 41), “Adding Images to the Print List (DPOF)” (= 2 93), or “Adding Images to a Photobook” (= 2 96).
Page 231: Editing Face Id Information
Editing Face ID Information If you notice that a name is incorrect during playback, you can change it or erase it. However, you cannot add names for people who are not detected by Face ID (names are not displayed), and for people whose names have been erased. Changing Names Access the setting screen. Press the <n> button and choose [Face ID Info] on the [ 1 ] tab (= 9 1). Press the <o> buttons or turn the <7> dial to choose [Edit ID Info], and then press the <m> button. Choose an image. Following the procedure on = 2 16, choose an image and press the <m> button. An orange frame is displayed around the selected face. When multiple names are displayed in an image, press the <q><r> buttons or turn the <7> dial to choose the name to change, and then press the <m> button. Choose the item to edit. Press the <o><q><r> buttons or turn the <7> dial to choose [Overwrite], and then press the <m> button. Choose the name of the person to overwrite. Follow step 2 on = 1 19 to choose the name of the person you want to overwrite.
Page 232 Editing Face ID Information • You can also access the [Edit ID Info] screen by touching an image on the screen in step 2, touching [ ] to display the orange frame, and then touching the face to overwrite. • You can also choose items to edit by touching them in step 3. Erasing Names Following step 3 on = 2 31, choose [Erase] and press the <m> button. After [Erase?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. • You can also erase names by touching [OK] after [Erase?] is displayed.
Page 233: Image Viewing Options
Image Viewing Options Still Images Magnifying Images Magnify an image. Moving the zoom lever toward <k> will zoom in and magnify the image. You can magnify images up to about 10x by continuing to hold the zoom lever. To zoom out, move the zoom lever toward <g>. You can return to single- image display by continuing to hold it. Move the display position and switch images as needed. To move the display position, press the Approximate Position <o><q><r> buttons. of Displayed Area To switch to other images while zoomed, turn the <7> dial. • You can return to single-image display from magniied display by pressing the <n> button. Touch-Screen Operations Spread your ingers apart (pinch out) to zoom in. You can magnify images up to about 10x by repeating this action. To move the display position, drag across the screen.
Page 234: Viewing Slideshows
Image Viewing Options Pinch in to zoom out. Touch [ ] to restore single-image display. Still Images Movies Viewing Slideshows Automatically play back images from a memory card as follows. Access the setting screen. Press the <n> button, and then choose [Slideshow] on the [ 1 ] tab (= 9 1). Conigure the setting. Choose a menu item to conigure, and then choose the desired option (= 9 1). Start automatic playback. Press the <o> buttons or turn the <7> dial to choose [Start], and then press the <m> button. The slideshow will start a few seconds after [Loading image...] is displayed. Press the <n> button to stop the slideshow. • The camera’s power-saving functions (= 8 6) are deactivated during slideshows.
Page 235 Image Viewing Options • To pause or resume slideshows, press the <m> button. • You can switch to other images during playback by pressing the <q><r> buttons or turning the <7> dial. For fast-forward or fast-rewind, hold the <q><r> buttons down. • [Play Time] cannot be modiied when [Bubble] is chosen in [Effect]. • You can also stop slideshows by touching the screen. Still Images Auto Playback of Similar Images (Smart Shufle) Based on the current image, the camera offers four images similar to it that you may wish to view. After you choose to view one of those images, the camera offers four more images. This is an enjoyable way to play back images in an unexpected order. Try this feature after you have taken many shots, in many kinds of scenes. Choose Smart Shufle. Press the <n> button, choose [Smart Shufle] on the [ 1 ] tab, and then press the <m> button (= 9 1). Four candidate images are displayed. Choose an image. Press the <o><q><r> buttons to choose the image you want to view next. Your chosen image is displayed in the center, surrounded by the next four candidate images. For full-screen display of the center image, press the <m> button. To restore the original display, press the <m>...
Page 236: Protecting Images
Protecting Images • Only still images shot with this camera are played back using Smart Shufle. • Smart Shufle is not available in the following cases: - There are less than 50 shots taken with this camera - An unsupported image is currently displayed - Images are shown in iltered display (= 2 25) - During group playback (= 2 30) • On the screen in step 2, touching an image above, below, or on either side will show your chosen image in the center, surrounded by the next four candidate images. • For full-screen display of the center image in step 2, touch that image. To restore the original display, touch the screen again. Still Images Movies Protecting Images Protect important images to prevent accidental erasure by the camera (= 2 40, 241). Choosing a Selection Method Access the setting screen. Press the <n> button and choose [Protect] on the [ 1 ] tab (= 9 1). Choose a selection method.
Page 237: Choosing Images Individually
Protecting Images • Protected images on a memory card will be erased if you format the card (= 2 67, 268). • Protected images cannot be erased using the camera’s erasure function. To erase them this way, irst cancel protection. Choosing Images Individually Choose [Select]. Following step 2 on = 2 36, choose [Select] and press the <m> button. Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. [ ] is displayed. To cancel selection, press the <m> button again. [ ] is no longer displayed. Repeat this process to specify other images. Protect the image. Press the <n> button. A conirmation message is displayed. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. • Images will not be protected if you switch to Shooting mode or turn the camera off before inishing the setup process in step 3. • You can also select or clear images by touching the screen in step 2, and you can access the conirmation screen by touching [ •...
Page 238: Selecting A Range
Protecting Images Selecting a Range Choose [Select Range]. Following step 2 on = 2 36, choose [Select Range] and press the <m> button. Choose a starting image. Press the <m> button. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Choose an ending image. Press the <r> button to choose [Last image], and then press the <m> button. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Images before the irst image cannot be selected as the last image.
Page 239: Specifying All Images At Once
Protecting Images Protect the images. Press the button to choose [Protect], and then press the <m> button. • You can also choose the irst or last image by turning the <7> dial when the top screen in steps 2 and 3 is displayed. • You can also choose the irst or last image by touching one of the images on the top of the screen in steps 2 and 3. • You can also protect images by touching [Protect] on the screen in step 4. Specifying All Images at Once Choose [Select All Images]. Following step 2 on = 2 36, choose [Select All Images] and press the <m> button. Protect the images. Press the <o> buttons or turn the <7> dial to choose [Protect], and then press the <m> button. • To cancel protection for groups of images, choose [Unlock] in step 4 of “Selecting a Range” or in step 2 of “Specifying All Images at Once”. • You can also protect or unlock images by touching [Protect] or [Unlock] on the screens described above.
Page 240: Erasing Images
Still Images Movies Erasing Images You can choose and erase unneeded images one by one. Be careful when erasing images, because they cannot be recovered. However, protected images (= 2 36) cannot be erased. Choose an image to erase. Press the <q><r> buttons or turn the <7> dial to choose an image. Erase the image. Press the <a> button. After [Erase?] is displayed, press the <q><r> buttons or turn the <7> dial to choose [Erase], and then press the <m> button. The current image is now erased. To cancel erasure, press the <q><r> buttons or turn the <7> dial to choose [Cancel], and then press the <m> button. • Pressing the <a> button while [ ] images are displayed will give you the option of choosing [Erase ], [Erase JPEG], or [Erase +JPEG] for deletion. • You can also erase the current image by touching [Erase] on the screen in step 2. • Images can also be erased by using Touch Actions (= 2 48).
Page 241: Erasing All Images
Erasing Images Erasing All Images You can erase all images at once. Be careful when erasing images, because they cannot be recovered. However, protected images (= 2 36) cannot be erased. Choosing a Selection Method Access the setting screen. Press the <n> button, and then choose [Erase] on the [ 1 ] tab (= 9 1). Choose a selection method. Choose a menu item and a setting as desired (= 9 1). To return to the menu screen, press the <n> button. Choosing Images Individually Choose [Select]. Following step 2 above, choose [Select] and press the <m> button. Choose an image. Once you follow step 2 on = 2 37 to choose an image, [ ] is displayed. To cancel selection, press the <m> button again. [ ] is no longer displayed.
Page 242 Erasing Images Erase the image. Press the <n> button. A conirmation message is displayed. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. Selecting a Range Choose [Select Range]. Following step 2 on = 2 41, choose [Select Range] and press the <m> button. Choose images. Follow steps 2 – 3 on = 2 38 to specify images. Erase the images. Press the button to choose [Erase], and then press the <m> button. Specifying All Images at Once Choose [Select All Images]. Following step 2 on = 2 41, choose [Select All Images] and press the <m> button. Erase the images. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 243: Rotating Images
Still Images Movies Rotating Images Change the orientation of images and save them as follows. Choose [Rotate]. Press the <n> button and choose [Rotate] on the [ 1 ] tab (= 9 1). Rotate the image. Press the <q><r> buttons or turn the <7> dial to choose an image. The image is rotated 90° each time you press the <m> button. To return to the menu screen, press the <n> button. • Movies with an image quality of [ ] or [ ] cannot be rotated. • Rotation is not possible when [Auto Rotate] is set to [Off] (see below). • On the screen in step 2, you can also touch [ ] to rotate images or touch ] to return to the menu screen. Deactivating Auto Rotation Follow these steps to deactivate automatic rotation by the camera, which rotates images shot in vertical orientation so they are displayed vertically on the camera. Press the <n> button, choose [Auto Rotate] on the [ 1 ] tab, and then choose [Off] (= 9 1).
Page 244: Image Categories
Image Categories • Images cannot be rotated (= 2 43) when you set [Auto Rotate] to [Off]. Additionally, images already rotated will be displayed in the original orientation. • In Smart Shufle (= 2 35) mode, even if [Auto Rotate] is set to [Off], images shot vertically will be displayed vertically, and rotated images will be displayed in the rotated orientation. Image Categories You can tag images as favorites or assign them to My Category (= 2 45) groups. By choosing a category in iltered playback, you can restrict the following operations to all of those images. • Viewing (= 2 16), Viewing Slideshows (= 2 34), Protecting Images (= 2 36), Erasing Images (= 2 40), Adding Images to the Print List (DPOF) (= 2 93), Adding Images to a Photobook (= 2 96) Still Images Movies Tagging Images as Favorites...
Page 245 Image Categories Finish the setup process. Press the <n> button. A conirmation message is displayed. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. • Images will not be tagged as favorites if you switch to Shooting mode or turn the camera off before inishing the setup process in step 3. • Favorite images will have a three-star rating ( ) when transferred to computers running Windows 7 or Windows Vista. (Does not apply to movies or RAW images.) • You can also select or clear current images by touching the screen in step 2. • Images can also be tagged as favorites by using Touch Actions (= 2 48). Still Images Movies Organizing Images by Category (My Category) You can organize images into categories. Note that images are automatically categorized at the time of shooting, according to shooting conditions. : I mages with detected faces, or images shot in [I] or [ ] mode. : I mages detected as [ ], [ ], or [ ] in <A> mode, or images...
Page 246 Image Categories Choose a selection method. Choose a menu item and a setting as desired (= 9 1). To return to the menu screen, press the <n> button. Choosing Images Individually Choose [Select]. Following step 2 above, choose [Select] and press the <m> button. Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image. Choose a category. Press the <o> buttons to choose a category and then press the <m> button. [ ] is displayed. To cancel selection, press the <m> button again. [ ] is no longer displayed. Repeat this process to choose additional images. Finish the setup process. Press the <n> button. A conirmation message is displayed. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. • Images will not be assigned to a category if you switch to Shooting mode or turn the camera off before inishing the setup process in step 4.
Page 247 Image Categories • You can also conirm your choice by touching [OK] on the screen in step 4. Selecting a Range Choose [Select Range]. Following step 2 on = 2 45, choose [Select Range] and press the <m> button. Choose images. Follow steps 2 – 3 on = 2 38 to specify images. Choose a category. Press the button to choose the type of image, and then press the <q><r> buttons or turn the <7> dial to choose a category. Finish the setup process. Press the button to choose [Select], and then press the <m> button. • You can clear the selection of all images in the [Select Range] category by choosing [Deselect] in step 4. • You can also choose a category by touching it (or touching [q][r]) on the screen in step 3, and you can conirm your choice by touching [Select].
Page 248: Convenient Control: Touch Actions
Still Images Movies Convenient Control: Touch Actions You can quickly and easily activate functions that you have assigned to four touch gestures (Touch Actions), in single-image display. Using a Function Assigned to [ ] Drag across the screen as shown. The function assigned to [ ] is now activated. Similarly, you can also activate functions assigned to [ ], [ ], and [ ] by dragging across the screen. Customize functions assigned to Touch Actions as desired. Changing Touch Actions Functions Simplify your preferred camera operations by reassigning dragging patterns to them as desired. Access the setting screen. Press the <n> button, and then choose [Set Touch Actions] on the [ 1 ] tab (= 9 1). Assign a function to a dragging pattern.
Page 249 Convenient Control: Touch Actions Assignable Functions Favorites Tag images as favorites, or untag the image. Next Favorite Switch to displaying the next image tagged as a favorite. Previous Favorite Switch to displaying the previous image tagged as a favorite. Switch to displaying the irst image with the next shooting Next Date date. Switch to displaying the irst image with the previous shooting Previous Date date. Smart Shufle Start Smart Shufle playback. To Camera To Smartphone Access the wireless LAN connection screen. To Computer For instructions on the wireless LAN function, refer to the Wireless LAN Guide (= 3 5). To Printer To Web Service Slideshow Start a slideshow. Erase Erase an image. Protect Protect an image or cancel protection. Rotate Rotate an image.
Page 250: Editing Still Images
Editing Still Images • Image editing (= 2 50 – 255) is only available when the memory card has suficient free space. • You can access editing screens for various functions by touching an image after choosing the function in the menu. • When [ ] is shown on an editing screen, you can touch [ ] instead of pressing the <n> button, if you prefer. • When [ ] is shown on an editing screen, you can touch [ ] instead of pressing the <m> button, if you prefer. Still Images Resizing Images Save a copy of images at a lower resolution. Choose [Resize]. Press the <n> button and choose [Resize] on the [ 1 ] tab (= 9 1). Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Choose an image size. Press the <q><r> buttons or turn the <7> dial to choose the size, and then press the <m> button.
Page 251 Editing Still Images Save the new image. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The image is now saved as a new ile. Review the new image. Press the <n> button. [Display new image?] is displayed. Press the <q><r> buttons or turn the <7> dial to choose [Yes], and then press the <m> button. The saved image is now displayed. • Editing is not possible for images saved as [ ] in step 3. • RAW images cannot be edited. • Images cannot be resized to a higher resolution. • You can also conigure this setting by touching the size on the screen in step 3, touching it again, and then touching [OK]. • You can also view saved images by touching [Yes] on the screen in step 5. Still Images Cropping You can specify a portion of an image to save as a separate image ile. Choose [Cropping]. Press the <n> button, and then choose [Cropping] on the [ 1 ] tab (= 9 1).
Page 252 Editing Still Images Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Adjust the cropping area. Cropping Area A frame is displayed around the portion of the image to be cropped. The original image is shown in the upper left, and a preview of the image as cropped is shown in the lower right. To resize the frame, move the zoom lever. To move the frame, press the Preview of Image After Cropping <o><q><r> buttons. Resolution After Cropping To change the frame orientation, press the <m> button. Faces detected in the image are enclosed in gray frames in the upper-left image. To crop the image based on this frame, turn the <7> dial to switch to the other frame. Press the <n> button. Save as a new image and review. Follow steps 4 – 5 on = 2 51. • Editing is not possible for images shot at a resolution of [ (= 1 24) or resized to [ ] (= 2 50). •...
Page 253 Editing Still Images • To move the frame, drag either image on the screen in step 3. • You can also resize frames by pinching in or out (= 2 33) on the screen in step 3. Still Images Changing Image Color Tones (My Colors) You can adjust image colors and then save the edited image as a separate ile. For details on each option, see = 1 77. Choose [My Colors]. Press the <n> button, and then choose [My Colors] on the [ 1 ] tab (= 9 1). Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Choose an option. Press the <q><r> buttons or turn the <7> dial to choose an option, and then press the <m> button. Save as a new image and review. Follow steps 4 – 5 on = 2 51.
Page 254 Editing Still Images • You can also conigure this setting by touching an option to select it on the screen in step 3 and then touching it again. Still Images Correcting Image Brightness (i-Contrast) Excessively dark image areas (such as faces or backgrounds) can be detected and automatically adjusted to the optimal brightness. Insuficient overall image contrast is also automatically corrected, to make subjects stand out better. Choose from four correction levels, and then save the image as a separate ile. Choose [i-Contrast]. Press the <n> button, and then choose [i-Contrast] on the [ 1 ] tab (= 9 1). Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. Choose an option. Press the <q><r> buttons or turn the <7> dial to choose an option, and then press the <m> button. Save as a new image and review. Follow steps 4 – 5 on = 2 51.
Page 255: Correcting Red-Eye
Editing Still Images • For some images, correction may be inaccurate or may cause images to appear grainy. • Images may look grainy after repeated editing using this function. • RAW images cannot be edited this way. • If [Auto] does not produce the expected results, try correcting images using [Low], [Medium], or [High]. • You can also conigure this setting by touching [q][r] on the screen in step Still Images Correcting Red-Eye Automatically corrects images affected by red-eye. You can save the corrected image as a separate ile. Choose [Red-Eye Correction]. Press the <n> button, and then choose [Red-Eye Correction] on the [ 1 ] tab (= 9 1). Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image. Correct the image. Press the <m> button. Red-eye detected by the camera is now corrected, and frames are displayed around corrected image areas. Enlarge or reduce images as needed. Follow the steps in = 2 33.
Page 256: Editing Movies
Editing Movies Save as a new image and review. Press the <o><q><r> buttons or turn the <7> dial to choose [New File], and then press the <m> button. The image is now saved as a new ile. Follow step 5 on = 2 51. • Some images may not be corrected accurately. • To overwrite the original image with the corrected image, choose [Overwrite] in step 4. In this case, the original image will be erased. • Protected images cannot be overwritten. • RAW images cannot be edited this way. • Red-eye correction can be applied to JPEG images shot in [ but the original image cannot be overwritten. • You can save images by touching [New File] or [Overwrite] on the screen in step 4. Movies Editing Movies You can cut movies to remove unneeded portions at the beginning or end. Choose [ * ]. Following steps 1 – 3 on = 2 16 – 217, choose [ * ] and press the <m> button. The movie editing panel and editing bar are now displayed.
Page 257 Editing Movies Specify portions to cut. Movie Editing Panel Press the <o> buttons to choose ] or [ To view the portions you can cut (identiied by [ ] on the screen), press the <q><r> buttons or turn the <7> dial to move [ ]. Cut the beginning of the movie (from [ ]) by choosing [ ], and cut the end of the movie by choosing Movie Editing Bar Even if you move [ ] to a position other than a [ ] mark, choosing [ ] will only cut the portion from the nearest [ ] to the left, and choosing [ ] will cut the portion from the nearest [ ] to the right. Review the edited movie. Press the <o> buttons to choose ], and then press the <m> button. The edited movie is now played. To edit the movie again, repeat step 2. To cancel editing, press the <o> buttons to choose [ ]. Press the <m> button, choose [OK] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button again. Save the edited movie. Press the <o> buttons to choose ], and then press the <m> button.
Page 258 Editing Movies • To overwrite the original movie with the cut one, choose [Overwrite] in step 4. In this case, the original movie will be erased. • [Overwrite] is only available when memory cards lack suficient free space. • Movies may not be saved if the battery runs out while saving is in progress. • When editing movies, you should use a fully charged battery or an AC adapter kit (sold separately, = 2 78).
Page 259 Editing Movies Movies Editing Movie Digest Clips Individual chapters (= 1 36) recorded in [ ] mode can be erased, as needed. Be careful when erasing chapters, because they cannot be recovered. Select the chapter to erase. Follow steps 1 – 2 on = 2 16 to choose a movie recorded in [ ] mode, and then press the <m> button to access the movie control panel. Press the <q><r> buttons or turn the <7> dial to choose [ ] or [ ], and then press the <m> button. Choose [ ]. Press the <q><r> buttons or turn the <7> dial to choose [ ], and then press the <m> button. The selected chapter is played back repeatedly. Conirm erasure. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. The chapter is erased, and the clip is overwritten.
Page 261: Setting Menu
Setting Menu Customize or adjust basic camera functions for greater convenience...
Page 262: Adjusting Basic Camera Functions
Adjusting Basic Camera Functions Functions can be conigured on the [3] tab. Customize commonly used functions as desired, for greater convenience (= 9 1). Silencing Camera Operations Silence camera sounds and movies as follows. Choose [Mute], and then choose [On]. • Operation can also be silenced by holding down the button as you turn the camera on. • Sound is not played during movies if you mute camera sounds (= 2 16). To restore sound during movies, press the <o> button or drag up across the screen. Adjust volume as needed by pressing the <o> buttons or by dragging up or down. Adjusting the Volume Adjust the volume of individual camera sounds as follows. Choose [Volume], and then press the <m> button. Choose an item, and then press the <q><r> buttons to adjust the volume.
Page 263: Hiding Hints And Tips
Adjusting Basic Camera Functions Customizing Sounds Customize camera operating sounds as follows. Choose [Sound Options], and then press the <m> button. Choose an item, and then press the <q><r> buttons to choose an option. Preset sounds 1, 2 (cannot be modiied) Preset sounds Can be changed by using the included software. • The default shutter sound is used in [ ] mode (= 1 58), regardless of any changes to [Shutter Sound]. Hiding Hints and Tips Hints and tips are normally shown when you choose FUNC. menu (= 8 9) or Menu (= 9 1) items. If you prefer, you can deactivate this information. Choose [Hints & Tips], and then choose [Off].
Page 264: Changing The Date And Time
Adjusting Basic Camera Functions Changing the Date and Time Adjust the date and time as follows. Access the [Date/Time] screen. Choose [Date/Time], and then press the <m> button. Conigure the setting. Press the <q><r> buttons to choose an item, and then adjust the setting, either by pressing the <o> buttons or turning the <7> dial. World Clock To ensure that your shots will have the correct local date and time when you travel abroad, simply register the destination in advance and switch to that time zone. This convenient feature eliminates the need to change the Date/ Time setting manually. Before using the world clock, be sure to set the date and time in “Setting the Date and Time” (= 1 8) and your home time zone. Specify your destination. Choose [Time Zone], and then press the <m> button. Press the <o> buttons or turn the <7> dial to choose [ World], and then press the <m> button. Press the <q><r> buttons or turn the <7> dial to choose the destination. To set daylight saving time (1 hour ahead), press the <o> buttons to choose [ Press the <m> button.
Page 265: Screen Brightness
Adjusting Basic Camera Functions Switch to the destination time zone. Press the <o> buttons or turn the <7> dial to choose [ World], and then press the <n> button. ] is now shown on the shooting screen (= 3 14). • Adjusting the date or time while in [ ] mode (= 2 64) will automatically update your [ Home] time and date. Screen Brightness Adjust screen brightness as follows. Choose [LCD Brightness], and then press the <q><r> buttons to adjust the brightness. • For maximum brightness, press and hold the button for at least one second when the shooting screen is displayed or when in single-image display. (This will override the [LCD Brightness] setting on the [3] tab.) To restore the original brightness, press and hold the button again for at least one second or restart the camera.
Page 266 Adjusting Basic Camera Functions Start-up Screen Customize the start-up screen shown after you turn the camera on as follows. Choose [Start-up Image], and then press the <m> button. Press the <q><r> buttons or turn the <7> dial to choose an option. No start-up image Preset image 1, 2 (cannot be modiied) Preset image Assign a desired shot, or use the included software to change the image. Customizing the Start-up Screen Access the [Start-up Image] screen in Playback mode. Press the <1> button. Following the previous procedure, choose [3] and press the <m> button. Choose one of your shots. Choose an image and press the <m> button. After [Register?] is displayed, choose [OK] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. • The previous start-up setting is overwritten when you assign a new start-up image.
Page 267: Formatting Memory Cards
Adjusting Basic Camera Functions • You can assign the operating sounds and start-up image for your camera from the included software. Refer to the Software Guide (= 2 7) for details. Formatting Memory Cards Before using a new memory card or a card formatted in another device, you should format the card with this camera. Formatting erases all data on a memory card. Before formatting, copy images on the memory card to a computer, or take other steps to back them An Eye-Fi card (= 3 00) contains software on the card itself. Before formatting an Eye-Fi card, install the software on a computer. Access the [Format] screen. Choose [Format], and then press the <m> button. Choose [OK]. Press the <o> buttons to choose [Cancel], choose [OK] (either press the <q><r> buttons or turn the <7> dial), and then press the <m> button. Format the memory card. To begin the formatting process, press the <o> buttons or turn the <7> dial to choose [OK], and then press the <m> button. When formatting is inished, [Memory card formatting complete] is displayed. Press the <m> button.
Page 268 Adjusting Basic Camera Functions • Formatting or erasing data on a memory card only changes ile management information on the card and does not erase the data completely. When transferring or disposing of memory cards, take steps to protect personal information if necessary, as by physically destroying cards. • The total card capacity indicated on the formatting screen may be less than the advertised capacity. Low-Level Formatting Perform low-level formatting in these cases: [Memory card error] is displayed, the camera is not working correctly, card image reading/writing is slower, continuous shooting is slower, or movie recording suddenly stops. Low-level formatting erases all data on a memory card. Before low-level formatting, copy images on the memory card to a computer, or take other steps to back them up. Perform low-level formatting. On the screen in step 2 on = 2 67, press the <o> buttons or turn the <7> dial to choose [Low Level Format], and then select this option (mark with a ]) by pressing the <q><r> buttons. Follow steps 2 – 3 on = 2 67 to continue with the formatting process. • Low-level formatting takes longer than “Formatting Memory Cards” (= 2 67), because data is erased from all storage regions of the memory card. • You can cancel low-level formatting in progress by choosing [Stop]. In this case, all data will be erased, but the memory card can be used normally.
Page 269: File Numbering
Adjusting Basic Camera Functions File Numbering Your shots are automatically numbered in sequential order (0001 – 9999) and saved in folders that store up to 2,000 images each. You can change how the camera assigns ile numbers. Choose [File Numbering], and then choose an option. Images are numbered consecutively (until the 9999th Continuous shot is taken/saved) even if you switch memory cards. Image numbering is reset to 0001 if you switch memory Auto Reset cards, or when a new folder is created. • Regardless of the option selected in this setting, shots may be numbered consecutively after the last number of existing images on newly inserted memory cards. To start saving shots from 0001, use an empty (or formatted (= 2 67)) memory card. • Refer to the Software Guide (= 2 7) for information on the card folder structure and image formats.
Page 270: Lens Retraction Timing
Adjusting Basic Camera Functions Date-Based Image Storage Instead of saving images in folders created each month, you can have the camera create folders each day you shoot to store shots taken that day. Choose [Create Folder], and then choose [Daily]. Images will now be saved in folders created on the shooting date. Lens Retraction Timing The lens is normally retracted for safety about one minute after you press the <1> button in Shooting mode (= 8 6). To have the lens retracted immediately after you press the <1> button, set the retraction timing to [0 sec.]. Choose [Lens Retract], and then choose [0 sec.].
Page 271 Adjusting Basic Camera Functions Power-Saving Adjustment Adjust the timing of automatic camera and screen deactivation (Auto Power Down and Display Off, respectively) as needed (= 8 6). Access the [Power Saving] screen. Choose [Power Saving], and then press the <m> button. Conigure the settings. After choosing an item, press the <q><r> buttons to adjust it as needed. • To conserve battery power, you should normally choose [On] for [Auto Power Down] and [1 min.] or less for [Display Off]. • The [Display Off] setting is applied even if you set [Auto Power Down] to [Off]. Metric/Non-Metric Display Change the unit of measurement shown in the MF indicator (= 1 82), zoom bar (= 9 6), and GPS information for elevation (= 7 8) from m/ cm to ft/in as needed. Choose [Units], and then choose [ft/in].
Page 272: Electronic Level Calibration
Adjusting Basic Camera Functions Electronic Level Calibration Calibrate the electronic level if it seems ineffective in helping you level the camera. For greater calibration accuracy, display grid lines (= 2 10) to help you level the camera in advance. Level the camera. Place the camera on a lat surface, such as a table. Access the [Electronic Level] screen. Choose [Electronic Level], and then press the <m> button. Calibrate the electronic level. Choose [Calibrate] and press the <m> button. A conirmation message is displayed. Choose [OK], and then press the <m> button. Resetting the Electronic Level Restore the electronic level to its original state as follows. Note that this is not possible unless you have calibrated the electronic level. Choose [Electronic Level], and then press the <m> button. Choose [Reset], and then press the <m> button. Choose [OK] and press the <m> button to reset the electronic level and return to the menu screen.
Page 273: Setting Copyright Information To Record In Images
Adjusting Basic Camera Functions Still Images Movies Increasing Touch-Screen Panel Sensitivity Sensitivity of the touch-screen panel can be increased, so that the camera responds to a lighter touch. Choose [Touch Response], and then choose [High]. Setting Copyright Information to Record in Images To record the author’s name and copyright details in images, set this information beforehand as follows. Access the setting screen. Choose [Copyright Info], and then press the <m> button. Press the <o> buttons or turn the <7> dial to choose [Enter Author’s Name] or [Enter Copyright Details], and then press the <m> button. Enter a name. Touch characters on the keyboard to enter them. Up to 63 characters can be used.
Page 274 Adjusting Basic Camera Functions Save the settings. Press the <n> button. [Accept changes?] is displayed. Press the <q><r> buttons or turn the <7> dial to choose [Yes], and then press the <m> button. The information set here will now be recorded in images. • To check the information entered, choose [Display Copyright Info] on the screen in step 1, and then press the <m> button. • You can also use the included software (= 2 7) to enter, change, and delete copyright information. Some characters entered with the included software may not display on the camera, but will be correctly recorded in images. • You can view, change, and delete copyright information recorded in images by using the included software to save images to a computer. • You can also enter a name on the screen in step 2 by pressing the <o><q><r> buttons or turning the <7> dial to select characters, and then pressing the <m> button. Move the cursor by turning the <y> ring, and press the < > button to delete characters, as needed. Deleting All Copyright Information You can delete both the author’s name and copyright details at the same time as follows. Follow step 1 on = 2 73 and choose [Delete Copyright Info]. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. •...
Page 275: Adjusting Other Settings
Adjusting Basic Camera Functions Checking Certiication Logos Some logos for certiication requirements met by the camera can be viewed on the screen. Other certiication logos are printed in this guide, on the camera packaging, or on the camera body. Choose [Certiication Logo Display], and then press the <m> button. Display Language Change the display language as needed. Access the [Language] screen. Choose [Language ], and then press the <m> button. Conigure the setting. Press the <o><q><r> buttons or turn the <7> dial to choose a language, and then press the <m> button. • You can also access the [Language] screen in Playback mode by pressing and holding the <m> button and immediately pressing the <n> button. Adjusting Other Settings The following settings can also be adjusted on the [3] tab. • [Video System] (= 2 84) • [Ctrl via HDMI] (= 2 82) • [Wireless LAN Settings] (= 3 5) •...
Page 276: Restoring Defaults
Adjusting Basic Camera Functions Restoring Defaults If you accidentally change a setting, you can restore default camera settings. Access the [Reset All] screen. Choose [Reset All], and then press the <m> button. Restore default settings. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. Default settings are now restored. • The following functions are not restored to default settings. - [3] tab settings [Date/Time] (= 1 8), [Language ] (= 2 0), [Time Zone] (= 2 64), [Video System] (= 2 84), and the image assigned to [Start-up Image] (= 2 66) - Information registered using Face ID (= 1 13) - Custom white balance data you have recorded (= 1 75) - Colors chosen in Color Accent (= 1 51) or Color Swap (= 1 52) - Shooting mode chosen in <K> (= 1 37) or <...
Page 277: Accessories
Accessories Use included accessories effectively and enjoy the camera in more ways with optional Canon accessories and other compatible accessories sold separately...
Page 278: Tips On Using Included Accessories
Tips on Using Included Accessories Effective Battery and Charger Use • Charge the battery on (or immediately before) the day of use Charged batteries gradually lose their charge, even when they are not used. You can easily check the charge state of the battery by attaching the cover so that ▲ is visible on a charged battery, and attaching it so that ▲ is not visible on an uncharged battery. • Long-term battery storage After using up all remaining battery power, remove the battery from the camera. Store the battery with the cover attached. Storing a partially charged battery over extended periods (about a year) may shorten its life or affect performance. • Using the battery charger abroad The charger can be used in areas with 100 – 240 V AC power (50/60 Hz). For power outlets in a different format, use a commercially available adapter for the plug. Never use an electrical transformer designed for traveling, which may damage the battery. Optional Accessories The following camera accessories are sold separately. Note that availability varies by area, and some accessories may no longer be available. Power Supplies Battery Pack NB-5L Rechargeable lithium-ion battery Battery Charger CB-2LX/CB-2LXE Charger for Battery Pack NB-5L...
Page 279 Optional Accessories AC Adapter Kit ACK-DC30 For powering the camera using household power. Recommended when using the camera over extended periods, or when connecting the camera to a printer or computer. Cannot be used to charge the camera battery. • The battery charger and AC adapter kit can be used in areas with 100 – 240 V AC power (50/60 Hz). • For power outlets in a different format, use a commercially available adapter for the plug. Never use an electrical transformer designed for traveling, which may damage the battery.
Page 280: Flash Unit
Optional Accessories Flash Unit High-Power Flash HF-DC2 External lash for illuminating subjects that are out of range of the built-in lash. Other Accessories Waterproof Case WP-DC47 For underwater photography at depths of up to 40 meters (130 ft.). Also useful for shooting in the rain, at the beach, or on ski slopes. Stereo AV Cable AVC-DC400ST Connect the camera to a TV to enjoy playback on the larger TV screen. HDMI Cable HTC-100 For connecting the camera to an HDMI input of a high-deinition TV. Printers Canon PictBridge-Compatible Printers Printing images without a computer is possible by connecting the camera to a Canon PictBridge-compatible printer. For details, visit your nearest Canon dealer.
Page 281: Using Optional Accessories
Still Images Movies Using Optional Accessories Still Images Movies Playback on a TV By connecting the camera to a TV, you can view your shots on the larger screen of the TV. For details on connection or how to switch inputs, refer to the TV manual. • Some information may not be displayed on the TV (= 3 16). Still Images Movies Playback on a High-Deinition TV Connecting the camera to an HDTV with the HDMI Cable HTC-100 (sold separately) enables you to view your shots on the larger screen of the TV. Movies shot at a resolution of [ ] or [ ] can be viewed in high-deinition. Make sure the camera and TV are off. Connect the camera to the TV. On the TV, insert the cable plug fully into the HDMI input as shown. On the camera, open the terminal cover and insert the cable plug fully into the camera terminal.
Page 282 Using Optional Accessories Turn the TV on and switch to video input. Switch the TV input to the video input you connected the cable to in step 2. Turn the camera on. Press the <1> button to turn the camera Images from the camera are now displayed on the TV. (Nothing is displayed on the camera screen.) When inished, turn off the camera and TV before disconnecting the cable. • Touch-screen operations are not supported while the camera is connected to a television. • Camera operating sounds are not played while the camera is connected to an HDTV. Still Images Movies Controlling the Camera with a TV Remote Connecting the camera to an HDMI CEC-compatible TV enables playback (including slideshow playback) using the TV remote control. In this case, you will need to adjust some TV settings. For details, refer to the TV user manual. Conigure the setting. Press the <n> button, choose [Ctrl via HDMI] on the [3] tab, and then choose [Enable] (= 9 1). Connect the camera to the TV. Follow steps 1 – 2 on = 2 81 to connect the camera to the TV.
Page 283 Using Optional Accessories Display images. Turn on the TV. On the camera, press the <1> button. Images from the camera are now displayed on the TV. (Nothing is displayed on the camera screen.) Control the camera with the TV remote. Press the <q><r> buttons on the remote to browse images. To display the camera control panel, press the OK/Select button. Select control panel items by pressing the <q><r> buttons to choose an item, and then pressing the OK/Select button again. Camera Control Panel Options Shown on the TV Return Closes the menu. Displays sets of images shot in [ ] mode (= 1 58). (Only Group Playback displayed when a grouped image is selected.) Starts movie playback. (Only displayed when a movie is Play Movie selected.) Starts slideshow playback. To switch images during Slideshow playback, press the <q><r> buttons on the remote control. Index Playback Displays multiple images in an index. Change Display Switches display modes (= 8 8). • Pressing the <n> button on the camera will switch control to the camera itself, which will prevent remote control until you return to single- image display.
Page 284 Using Optional Accessories Still Images Movies Playback on a Standard-Deinition TV Connecting the camera to a TV with the Stereo AV Cable AVC-DC400ST (sold separately) enables you to view your shots on the larger screen of the TV as you control the camera. Make sure the camera and TV are off. Connect the camera to the TV. White Yellow On the TV, insert the cable plugs fully into Yellow the video inputs as shown. White On the camera, open the terminal cover and insert the cable plug fully into the camera terminal. Display images. Follow steps 3 – 4 on = 2 82 to display images. • Correct display is not possible unless the camera video output format (NTSC or PAL) matches the TV format. To change the video output format, press the <n> button and choose [Video System] on the [3] tab. • Touch-screen operations are not supported while the camera is connected to a television. • When the camera and TV are connected, you can also shoot while previewing shots on the larger screen of the TV. To shoot, follow the same steps as when using the camera screen. However, AF-Point Zoom (= 1 30), MF-Point Zoom (= 1 82) and Stitch Assist (= 1 60) are not available.
Page 285: Powering The Camera With Household Power
Using Optional Accessories Still Images Movies Powering the Camera with Household Power Powering the camera with AC Adapter Kit ACK-DC30 (sold separately) eliminates the need to monitor the remaining battery level. Make sure the camera is off. Insert the coupler. Follow step 2 on = 1 6 to open the cover. Insert the coupler facing the direction shown, just as you would a battery (following step 3 on = 1 6). Terminal Follow step 5 on = 1 7 to close the cover. Connect the adapter to the coupler. Open the cover and insert the adapter plug fully into the coupler. Connect the power cord. Insert one end of the power cord into the compact power adapter, and then plug the other end into a power outlet. Turn the camera on and use it as desired. When inished, turn the camera off and unplug the power cord from the outlet.
Page 286: Printing Images
Printing Images • Do not disconnect the adapter or unplug the power cord while the camera is still on. This may erase your shots or damage the camera. • Do not attach the adapter or adapter cord to other objects. Doing so could result in malfunction or damage to the product. Still Images Movies Printing Images Your shots can easily be printed by connecting the camera to a printer. On the camera, you can specify images to set up batch printing, prepare orders for photo development services, and prepare orders or print images for photobooks. A Canon SELPHY CP series compact photo printer is used here for the sake of illustration. Screens displayed and available functions vary by printer. Also refer to the printer manual for additional information. Still Images Easy Print Easily print your shots by connecting the camera to a PictBridge-compatible printer (sold separately) with the included interface cable (= 2 ). Make sure the camera and printer are off. Connect the camera to the printer. Open the cover. Holding the smaller cable plug in the orientation shown, insert the plug fully into the camera terminal. Connect the larger cable plug to the printer. For other connection details, refer to the printer manual.
Page 287 Printing Images Turn the printer on. Turn the camera on. Press the <1> button to turn the camera ] is displayed. Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image. Access the printing screen. Press the <m> button. Print the image. Press the <o> buttons or turn the <7> dial to choose [Print], and then press the <m> button. Printing now begins. To print other images, repeat steps 5 – 6 after printing is inished. When you are inished printing, turn the camera and printer off and disconnect the interface cable. • For Canon PictBridge-compatible printers (sold separately), see = 2 80. • RAW images cannot be printed.
Page 288 Printing Images Still Images Coniguring Print Settings Access the printing screen. Follow steps 1 – 6 on = 2 86 – 287 to access the screen at left. Conigure the settings. Press the <o> buttons or turn the <7> dial to choose an item, and then choose an option by pressing the <q><r> buttons. Default Matches current printer settings. Date Prints images with the date added. File No. Prints images with the ile number added. Both Prints images with both the date and ile number added. – Default Matches current printer settings. – Uses information from the time of shooting to print under optimal settings. Red-Eye 1 Corrects red-eye. No. of Copies Choose the number of copies to print. – Cropping Specify a desired image area to print (= 2 89). Paper Specify the paper size, layout, and other details –...
Page 289 Printing Images Still Images Cropping Images Before Printing (Cropping) By cropping images before printing, you can print a desired image area instead of the entire image. Choose [Cropping]. After following step 1 on = 2 88 to access the printing screen, choose [Cropping] and press the <m> button. A cropping frame is now displayed, indicating the image area to print. Adjust the cropping frame as needed. To resize the frame, move the zoom lever. To move the frame, press the <o><q><r> buttons. To rotate the frame, turn the <7> dial. When inished, press the <m> button. Print the image. Follow step 7 on = 2 87 to print. On the screen in step 1, press the <o> buttons or turn the <7> dial to choose [Print], and then press the <m> button. • Cropping may not be possible at small image sizes, or at some aspect ratios. • Dates may not be printed correctly if you crop images shot with [Date Stamp] selected.
Page 290 Printing Images Still Images Choosing Paper Size and Layout Before Printing Choose [Paper Settings]. After following step 1 on = 2 88 to access the printing screen, choose [Paper Settings] and press the <m> button. Choose a paper size. Press the <o> buttons or turn the <7> dial to choose an option, and then press the <m> button. Choose a type of paper. Press the <o> buttons or turn the <7> dial to choose an option, and then press the <m> button. Choose a layout. Press the <o> buttons or turn the <7> dial to choose an option. When choosing [N-up], press the <q><r> buttons to specify the number of images per sheet. Press the <m> button. Print the image.
Page 291 Printing Images Available Layout Options Default Matches current printer settings. Bordered Prints with blank space around the image. Borderless Borderless, edge-to-edge printing. N-up Choose how many images to print per sheet. Prints images for identiication purposes. ID Photo Only available for images with a resolution of L and an aspect ratio of 4:3. Choose the print size. Fixed Size Choose from 3.5 x 5 in., postcard, or wide-format prints. Still Images Printing ID Photos Choose [ID Photo]. Following steps 1 – 4 on = 2 90, choose [ID Photo] and press the <m> button. Choose the long and short side length. Press the <o> buttons or turn the <7> dial to choose an item. Choose the length by pressing the <q><r> buttons, and then press the <m> button. Choose the printing area. Follow step 2 on = 2 89 to choose the printing area. Print the image.
Page 292: Printing Movie Scenes
Printing Images Movies Printing Movie Scenes Access the printing screen. Follow steps 1 – 5 on = 2 86 – 287 to choose a movie, and then press the <m> button. Press the <q><r> buttons or turn the <7> dial to choose [c], and then press the <m> button. The screen at left is displayed. Choose a printing method. Press the <o> buttons or turn the <7> dial to choose [ ], and then press the <q><r> buttons to choose the printing method. Press the <o> buttons to choose ], and then press the <q><r> buttons to choose the printing method. Print the image. Movie Printing Options Single Prints the current scene as a still image. Prints a series of scenes, a certain interval apart, on a single sheet of Sequence paper. You can also print the folder number, ile number, and elapsed time for the frame by setting [Caption] to [On]. • To cancel printing in progress, press the <m> button. • [ID Photo] and [Sequence] cannot be chosen on Canon PictBridge- compatible printers from CP720/CP730 and earlier models.
Page 293 Printing Images Still Images Adding Images to the Print List (DPOF) Batch printing (= 2 96) and ordering prints from a photo development service can be set up on the camera. Choose up to 998 images on a memory card and conigure relevant settings, such as the number of copies, as follows. The printing information you prepare this way will conform DPOF (Digital Print Order Format) standards. • RAW images cannot be included in print list. Still Images Coniguring Print Settings Specify the printing format, whether to add the date or ile number, and other settings as follows. These settings apply to all images in the print list. Press the <n> button, and then choose [Print Settings] on the [2] tab. Choose and conigure settings as desired (= 9 1). Standard One image is printed per sheet. Smaller versions of multiple images are printed Print Type Index per sheet. Both Both standard and index formats are printed. Images are printed with the shooting date. Date –...
Page 294 Printing Images • Not all of your DPOF settings may be applied in printing by the printer or photo development service, in some cases. • ] may be displayed on the camera to warn you that the memory card has print settings that were conigured on another camera. Changing the print settings using this camera may overwrite all previous settings. • Setting [Date] to [On] may cause some printers to print the date twice. • Specifying [Index] will prevent you from choosing [On] for both [Date] and [File No.] at the same time. • Index printing is not available on some Canon PictBridge-compatible printers (sold separately). • The date is printed in a format matching setting details in [Date/Time] on the [3] tab (= 1 8). Still Images Setting Up Printing for Individual Images Choose [Select Images & Qty.]. Press the <n> button, choose [Select Images & Qty.] on the [2] tab, and then press the <m> button. Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. You can now specify the number of copies. If you specify index printing for the image, it is labeled with a [ ] icon. To cancel index printing for the image, press the <m> button again. [...
Page 295 Printing Images Specify the number of prints. Press the <o> buttons or turn the <7> dial to specify the number of prints (up to 99). To set up printing for other images and specify the number of prints, repeat steps 2 – 3. Printing quantity cannot be speciied for index prints. You can only choose which images to print, by following step 2. When inished, press the <n> button to return to the menu screen. Still Images Setting Up Printing for a Range of Images Choose [Select Range]. Following step 1 on = 2 94, choose [Select Range] and press the <m> button. Choose images. Follow steps 2 – 3 on = 2 38 to specify images. Conigure the print settings. Press the <o> buttons to choose [Order], and then press the <m> button. Still Images Setting Up Printing for All Images Choose [Select All Images]. Following step 1 on = 2 94, choose [Select All Images] and press the <m> button. Conigure the print settings. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 296: Adding Images To A Photobook
Printing Images Still Images Clearing All Images from the Print List Choose [Clear All Selections]. Following step 1 on = 2 94, choose [Clear All Selections] and press the <m> button. Conirm clearing the print list. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button. Still Images Printing Images Added to the Print List (DPOF) When images have been added to the print list (= 2 93 – 295), the screen at left is displayed after you connect the camera to a PictBridge-compatible printer. Press the <o> buttons to choose [Print now], and then simply press the <m> button to print the images in the print list. Any DPOF print job that you temporarily stop will be resumed from the next image. Still Images Adding Images to a Photobook Photobooks can be set up on the camera by choosing up to 998 images on a memory card and importing them into the included software on your computer, where they are stored in their own folder. This is convenient when ordering printed photobooks online or printing photobooks with your own printer.
Page 297 Printing Images Choosing a Selection Method Press the <n> button, choose [Photobook Set-up] on the [ 1 ] tab, and then choose how you will select images. • ] may be displayed on the camera to warn you that the memory card has print settings that were conigured on another camera. Changing the print settings using this camera may overwrite all previous settings. • After importing images to your computer, also refer to the Software Guide (= 2 7) and the printer manual for further information. Still Images Adding Images Individually Choose [Select]. Following the procedure on = 2 97, choose [Select] and press the <m> button.
Page 298 Printing Images Choose an image. Press the <q><r> buttons or turn the <7> dial to choose an image, and then press the <m> button. ] is displayed. To remove the image from the photobook, press the <m> button again. [ ] is no longer displayed. Repeat this process to specify other images. When inished, press the <n> button to return to the menu screen. • You can also choose the images by touching them on the screen in step 2. Still Images Adding All Images to a Photobook Choose [Select All Images]. Following the procedure on = 2 97, choose [Select All Images] and press the <m> button. Conigure the print settings. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 299 Printing Images Still Images Removing All Images from a Photobook Choose [Clear All Selections]. Following the procedure on = 2 97, choose [Clear All Selections] and press the <m> button. Conirm clearing the photobook. Press the <q><r> buttons or turn the <7> dial to choose [OK], and then press the <m> button.
Page 300: Using An Eye-Fi Card
Still Images Movies Using an Eye-Fi Card Before using an Eye-Fi card, always conirm that local use is permitted (= 2 ). Inserting a prepared Eye-Fi card enables automatic wireless transfer of images to a computer or uploading to a photo-sharing website. Images are transferred by the Eye-Fi card. Refer to the card’s user manual or contact the manufacturer for instructions on preparing and using cards or resolving transfer problems. • When using an Eye-Fi card, keep the following points in mind. - Cards may continue to transmit radio waves even when [Eye- Fi trans.] is set to [Disable] (= 3 01). Remove the Eye-Fi card before entering hospitals, aircraft, or other areas where transmission is prohibited. - When troubleshooting image transfer issues, check the card and computer settings. For details, refer to the card’s user manual. - Poor Eye-Fi connections may cause image transfer to take a long time, and transfer may be interrupted in some cases. - Eye-Fi cards may become hot, due to their transfer functions. - Battery power will be consumed faster than in normal use. - Camera operation may become sluggish. To resolve this, try setting [Eye-Fi trans.] to [Disable]. - Eye-Fi transmission is not possible when the camera is connected to a wireless LAN. Connection status of Eye-Fi cards in the camera can be checked on the shooting screen (in regular information display mode) or playback screen (in simple information display mode). (Gray) Not connected Interrupted (Blinking white) Connecting...
Page 301: Checking Connection Information
Using an Eye-Fi Card Images labeled with a [ ] icon have been transferred. • Choosing [ ] mode will interrupt the Eye-Fi connection. Although the Eye-Fi connection will be restored after you choose another shooting mode or enter Playback mode, the camera may transfer any movies made in [ ] mode again. Checking Connection Information Check the access point SSID used by the Eye-Fi card or the connection status, as needed. Press the <n> button, choose [Eye-Fi Settings] on the [3] tab, and then press the <m> button. Choose [Connection info], and then press the <m> button. The connection information screen is displayed. Disabling Eye-Fi Transfer Conigure the setting as follows to disable Eye-Fi transfer by the card, if necessary. Choose [Disable] in [Eye-Fi trans.]. Press the <n> button, choose [Eye-Fi Settings] on the [3] tab, and then press the <m> button. Choose [Eye-Fi trans.], and then choose [Disable]. • [Eye-Fi Settings] is not shown unless an Eye-Fi card is in the camera with its write-protect tab in the unlocked position. For this reason, you cannot change settings for an inserted Eye-Fi card if the write-protect tab is in the locked position.
Page 303: Appendix
Appendix Helpful information when using the camera...
Page 304: Troubleshooting
Troubleshooting If you think there is a problem with the camera, irst check the following. If the items below do not solve your problem, contact a Canon Customer Support Help Desk. Power Nothing happens when the power button is pressed. • Conirm that the battery is charged (= 1 5). • Conirm that the battery is inserted facing the correct way (= 1 6). • Conirm that the memory card/battery cover is fully closed (= 1 7). • Dirty battery terminals reduce battery performance. Try cleaning the terminals with a cotton swab and reinserting the battery a few times. The battery is depleted quickly. • Battery performance decreases at low temperatures. Try warming the battery a little by putting it in your pocket, for example, with the terminal cover on. • If these measures do not help and the battery is still depleted soon after charging, it has reached the end of its life. Purchase a new battery. The lens is not retracted. • Do not open the memory card/battery cover while the camera is on. Close the cover, turn the camera on, and then turn it off again (= 1 7). The battery is swollen. •...
Page 305 Troubleshooting • Date stamps are not added in shooting modes (= 3 28 – 329) in which this setting cannot be conigured. [h] lashes on the screen when the shutter button is pressed, and shooting is not possible (= 9 9). • Set [IS Mode] to [Continuous] (= 1 99). • Set the lash mode to [h] (= 1 93). • Increase the ISO speed (= 1 69). • Mount the camera on a tripod or take other measures to keep it still. In this case, you should set [IS Mode] to [Off] (= 1 99). Shots are out of focus. • Press the shutter button halfway to focus on subjects before pressing it all the way down to shoot (= 8 7). •...
Page 306 Troubleshooting • Adjust brightness by using lash exposure compensation or changing the lash output level (= 1 95, 197). • Increase the ISO speed (= 1 69). Subjects in lash shots look too bright, highlights are washed-out. • Shoot within lash range (= 3 35). • Set the lash mode to [!] (= 1 11). • Adjust brightness by using lash exposure compensation or changing the lash output level (= 1 95, 205). White dots or similar image artifacts appear in lash shots. • This is caused by light from the lash relecting off dust or airborne particles. Shots look grainy. • Lower the ISO speed (= 1 69). • High ISO speeds in some shooting modes may cause grainy images (= 1 39). Subjects are affected by red-eye (= 1 25).
Page 307: Shooting Movies
Troubleshooting Shooting Movies The elapsed time shown is incorrect, or recording is interrupted. • Use the camera to format the memory card, or switch to a card that supports high- speed recording. Note that even if the elapsed time display is incorrect, the length of movies on the memory card corresponds to the actual recording time (= 3 34, 267). ] is displayed and shooting stops automatically. The camera’s internal memory buffer illed up as the camera could not record to the memory card quickly enough. Try one of the following measures. • Use the camera to perform low-level formatting of the memory card (= 2 68). • Lower the image quality (= 1 27). • Switch to a memory card that supports high-speed recording (= 3 34). Zooming is not possible. • Zooming is not possible when shooting movies in [ ] (= 1 46) and [ ] (= 1 62) modes.
Page 308: Wireless Lan
Troubleshooting Computer Cannot transfer images to a computer. When attempting to transfer images to the computer via a cable, try reducing the transfer speed as follows. • Press the <1> button to enter Playback mode. Hold the <n> button down as you press the <o> and <m> buttons at the same time. On the next screen, press the <q><r> buttons to choose [B], and then press the <m> button. Eye-Fi Cards Cannot transfer images (= 3 00). Wireless LAN Cannot access the wireless LAN menu by pressing <o>. • You cannot access the wireless LAN menu from a shooting mode. Switch to Playback mode and try again. • Note that in Playback mode, the wireless LAN menu cannot be displayed during detailed information display, magniied display, or index display. Switch to single- image display and a viewing mode other than detailed information display. Similarly, the wireless LAN menu cannot be accessed during iltered image display according to speciied conditions. Cancel the playback state of the image in image search mode. • The wireless LAN menu cannot be displayed while the camera is connected to a printer or computer via a cable. Disconnect the cable. Cannot add a device/destination. • A total of 20 items of connection information can be added to the camera. Erase unneeded connection information from the camera irst, and then add new devices/ destinations (= 7 8). • E-mail is the only web service for which multiple accounts can be set. Use CameraWindow to change the desired Web service accounts (= 4 6).
Page 309 Troubleshooting Cannot send images. • The destination device has insuficient storage space. Increase the storage space on the destination device and resend the images. • The write-protect tab of the SD/SDHC/SDXC memory card or Eye-Fi card of the destination camera is set to the locked position. Slide the write-protect tab to the unlocked position. • Images shot in [ ] mode are grouped. Cancel grouping and then send the images. • RAW images cannot be sent. In [ ] mode, only the JPEG images are sent. Cannot resize images for sending. • Images cannot be resized to be bigger than the resolution setting of their original size. • Movies cannot be resized. Images take a long time to send./The wireless connection is disrupted. • Multiple images may take a long time to send. Try resizing the image to [ ] or [ to reduce sending time (= 7 6). • Movies may take a long time to send. • Avoid using the camera’s wireless LAN function around microwave ovens, Bluetooth devices, and other devices that operate on the 2.4 GHz band, as this will weaken wireless LAN signals. • Note that images may take a long time to send even when [ ] is displayed. • Bring the camera closer to the other device you are trying to connect to (such as the access point), and make sure there are no objects between the devices. •...
Page 310: On-Screen Messages
1 6). Cannot record! • Shooting was attempted without a memory card in the camera. To shoot, insert a memory card facing the correct way (= 1 7). Memory card error (= 2 68) • If the same error message is displayed even when you have inserted a formatted memory card facing the correct way, contact a Canon Customer Support Help Desk (= 1 7). Insuficient space on card • There is not enough free space on the memory card to shoot (= 9 5, 135, 165, 201) or edit images (= 2 50 – 255). Either erase unneeded images (= 2 40, 241) or insert a memory card with enough free space (= 1 6). Touch AF unavailable •...
Page 311 (= 2 40), Favorites (= 2 44), My Category (= 2 45), Print List (= 2 93), or Photobook Set-up (= 2 96). Communication error • An excessive amount of images (approx. 1,000) on the memory card prevented printing or image transfer to a computer. To transfer the images, use a commercially available USB card reader. To print, insert the memory card directly into the printer card slot. Naming error! • The folder could not be created or images could not be recorded, because the highest supported folder number (999) for storing images on the card has been reached and the highest supported image number (9999) for images in folders has been reached. In the [3] menu, change [File Numbering] to [Auto Reset] (= 2 69), or format the memory card (= 2 67). Lens Error • This error may occur if the lens is held while it is moving, or when the camera is used in dusty or sandy locations. • Frequent display of this error message may indicate camera damage. In this case, contact a Canon Customer Support Help Desk.
Page 312 On-Screen Messages A camera error was detected (error number) • If this error message is displayed immediately after a shot, the image may not have been saved. Switch to Playback mode to check for the image. • Frequent display of this error message may indicate camera damage. In this case, write down the error number (Exx) and contact a Canon Customer Support Help Desk. File Error • Correct printing (= 2 86) may not be possible for photos from other cameras or images that have been altered using computer software, even if the camera is connected to the printer. Print error • Check the paper size setting (= 2 90). If this error message is displayed when the setting is correct, restart the printer and complete the setting on the camera again. Ink absorber full • Contact a Canon Customer Support Help Desk to request assistance with ink absorber replacement. Wireless LAN Connection failed • No access points were recognized. Check the access point settings. (= 5 7) • A device could not be found. Turn the camera off and on again, and retry the connection.
Page 313 On-Screen Messages Disconnected/Receiving failed/Sending failed • The environment you are in may not be suitable for wireless LAN use. • Avoid using the camera’s wireless LAN function around microwave ovens, Bluetooth devices, and other devices that operate on the 2.4 GHz band. • Bring the camera closer to the other device you are trying to connect to (such as the access point), and make sure there are no objects between the devices. • Check the connected device to make sure it is not experiencing errors. Sending failed Memory card error • If the same error message is displayed even when you have inserted a formatted memory card facing the correct way, contact a Canon Customer Support Help Desk. Receiving failed Insuficient space on card • There is not enough free space on the memory card to receive images. Erase images to create space on the memory card, or insert an empty memory card. Receiving failed Memory card locked • The write-protect tab of the SD/SDHC/SDXC memory card or Eye-Fi card of the camera to receive the images is set to the locked position. Slide the write-protect tab to the unlocked position. Receiving failed Naming error! • When the highest folder number (999), and the highest image number (9999) have been reached on the receiving camera, images cannot be received. Insuficient space on server • Delete unnecessary images uploaded to CANON iMAGE GATEWAY to create space. SSL certiicate not valid Connect to a computer, use the supplied software to reset • Check to make sure the date/time settings on the camera are correct. After conirming that the settings are correct, follow the on-screen instructions and reset the settings.
Page 314: On-Screen Information
On-Screen Information Shooting (Information Display) Battery level Histogram (= 2 10, Shooting mode (= 3 15) 219) (= 3 18), Scene icon (= 1 01) Camera orientation Recordable shots (= 3 34) Flash mode Eye-Fi connection (= 1 11, 193, status (= 3 00) Self-timer (= 1 07) 194) White balance...
Page 315 On-Screen Information ND ilter (= 1 73) i-Contrast (= 1 72) Exposure level (= 2 04) AE lock (= 1 67), White balance FE lock (= 1 96) (= 1 74) MF indicator (= 1 82) Grid lines (= 2 10) Mercury lamp correction (= 1 26) Image stabilization Shutter speed (= 1 99)
Page 316 On-Screen Information Playback (Detailed Information Display) Switch display: RGB Battery level File size (= 3 34) histogram (= 2 20), (= 3 15) Still images: GPS information Metering method Resolution (= 3 34) (= 2 20) (= 1 68) Movies: Movie My Category length (= 3 34) Folder number - File (= 2 45) number (= 2 69)
Page 317 On-Screen Information • Some information may not be displayed when viewing images on a TV (= 2 81). Summary of Movie Control Panel in “Viewing” (= 2 16) Exit Touch to display the volume panel, and then touch [o][p] to adjust the volume. At a volume of 0, [ ] is displayed. Play Slow Motion (To adjust the playback speed, press the <q><r> buttons or turn the <7> dial. No sound is played.) Skip Backward or Previous Clip (= 1 36) (To continue skipping backward, keep holding down the <m> button.) Previous Frame (For fast-rewind, keep holding down the <m> button.) Next Frame (For fast-forward, keep holding down the <m> button.) Skip Forward or Next Clip (= 1 36) (To continue skipping forward, keep holding down the <m> button.) Edit (= 2 56) Shown when you have selected a movie created in [ ] mode (= 2 59). Shown when the camera is connected to a PictBridge-compatible printer (= 2 86).
Page 318: Functions And Menu Tables
Functions and Menu Tables Functions Available in Each Shooting Mode Shooting Mode D B M G A Function – – O O O Exposure Compensation (= 1 66) Flash (= 1 11, 193, 194) – – – O O O – O O O –...
Page 319 Functions and Menu Tables S P t O O O O O O O O O – O O O O O O O – – – – – – O O O – – – O O O O O O O O O – –...
Page 320 Functions and Menu Tables FUNC. Menu Shooting Mode D B M G A Function DR Correction (= 1 72) – O O O – – – – – – – – Shadow Correct (= 1 73) – O O O O – – ISO Speed (= 1 69) –...
Page 321 Functions and Menu Tables S P t O O O O O – O O O O O O O O O O O O O – – – – – – – – O – – – – – – – – –...
Page 322 Functions and Menu Tables Shooting Mode D B M G A Function Self-Timer (= 1 07) O O O O O O [ $ O O O Self-Timer Settings (= 1 08) Delay O O O – O O Shots Metering Method (= 1 68) O O O –...
Page 323 Functions and Menu Tables S P t O O O O O O O O O O O O O O O O O O O O O O – – – – O O O O O O O O O O O O O O O O O O –...
Page 324: Shooting Menu
Functions and Menu Tables 4 Shooting Menu Shooting Mode D B M G A Function AF Frame (= 1 84) Face AiAF O O O – O O – 1-point AF Frame Size (= 1 85) – O O – Normal – O O – Small Digital Zoom (= 1 05, 183) –...
Page 325 Functions and Menu Tables S P t O O O O O – O – – O O – – O O O O O O O O O – – – O – O O O O – O O – O O O O O O O O O –...
Page 326 Functions and Menu Tables Shooting Mode D B M G A Function Flash Settings (= 1 25, 132, 195, 197, 205) – Auto O O O Flash Mode – – – – – Manual – – O – – Flash Exp. Comp – – – – – Flash Output 1st-curtain O O O Shutter Sync.
Page 327 Functions and Menu Tables S P t – O O O – O – O O O O O O O O O – – – O O O – – – – – – – – – – – – – – –...
Page 328 Functions and Menu Tables Shooting Mode D B M G A Function Custom Display (= 2 10) Shooting Info O O O Grid Lines O O O Electronic Level O O O Histogram O O O IS Mode (= 1 99) O O O Continuous O O O – –...
Page 329 Functions and Menu Tables S P t O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O –...
Page 330: Set Up Menu
Functions and Menu Tables 3 Set up Menu Item Ref. Page Item Ref. Page Mute = 2 62 Power Saving = 8 6, 271 Volume = 2 62 Units = 2 71 Sound Options = 2 63 Electronic Level = 1 29 Hints & Tips = 2 63 Video System = 2 84...
Page 331: Playback Menu
Functions and Menu Tables 1 Playback Menu Item Ref. Page Item Ref. Page Image Search = 2 25 Red-Eye Correction = 2 55 Movie Digest Playback = 2 29 Cropping = 2 51 Smart Shufle = 2 35 Resize = 2 50 Slideshow = 2 34 My Colors = 2 53 Erase...
Page 332: Handling Precautions
Handling Precautions • The camera is a high-precision electronic device. Avoid dropping it or subjecting it to strong impact. • Never bring the camera near magnets, motors, or other devices that generate strong electromagnetic ields, which may cause malfunction or erase image data. • If water droplets or dirt adheres to the camera or screen, wipe with a dry soft cloth, such as an eyeglass cloth. Do not rub hard or apply force. • Never use cleaners containing organic solvents to clean the camera or screen. • Use a blower brush to remove dust from the lens. If cleaning is dificult, contact a Canon Customer Support Help Desk. • To prevent condensation from forming on the camera after sudden temperature changes (when the camera is transferred from cold to warm environments), put the camera in an airtight, resealable plastic bag and let it gradually adjust to the temperature before removing it from the bag. • If condensation does form on the camera, stop using it immediately. Continuing to use the camera in this state may damage it. Remove the battery and memory card, and wait until the moisture has evaporated before resuming use.
Page 333: Speciications
Speciications Camera Effective Approx. 12.1 million pixels Pixels (Max.) 5x zoom: 5.2 (W) – 26.0 (T) mm Lens Focal Length (35mm ilm equivalent: 24 (W) – 120 (T) mm) 3.0 type color TFT LCD (touch-screen panel) LCD Monitor Effective Pixels: Approx. 461,000 dots Design rule for Camera File system, DPOF (version 1.1) File Format compliant Still Images: Exif 2.3 (JPEG), RAW (CR2 (Canon Original)) Data Type Movies: MOV (Image data: H.264; Audio data: Linear PCM (stereo)) Hi-speed USB HDMI output Interface Analog audio output (stereo) Analog video output (NTSC/PAL) Battery Pack NB-5L Power Source AC Adapter Kit ACK-DC30 Wireless LAN IEEE802.11b/g/n * 2.4 GHz band only Speciication Wireless LAN OFDM modulation (IEEE 802.11g/n) DSSS modulation (IEEE 802.11b) Transmission Method Wireless LAN Infrastructure mode , Ad hoc mode * Supports Wi-Fi Protected Setup Connection Mode Supported Wireless 1 – 13 (PC1819) or 1 – 11 (PC1882) Channels...
Page 334 3721 15020 7442 30040 (Medium 2) 2M/1600x1200 12927 52176 27291 110150 (Small) 0.3M/640x480 40937 165225 RAW Images – 1804 4160x3124 • The values in the table are measured according to Canon standards and may change depending on the subject, memory card and camera settings. • The values in the table are based on 4:3 aspect ratio. If the aspect ratio is changed (= 1 23), more images can be shot because the data size per image will be smaller than with 4:3 images. However, since [ ] 16:9 images have a setting of 1920 x 1080 pixels, their data size will be larger than 4:3 images. Recording Time per Memory Card Recording Time per Memory Card Image Quality 8 GB 32 GB 29 min. 39 sec. 1 hr. 59 min. 43 sec. 42 min. 11 sec. 2 hr. 50 min. 19 sec. 1 hr. 28 min. 59 sec. 5 hr. 59 min. 10 sec. *1 27 min. 39 sec. for iFrame movies (= 1 62).
Page 335 Speciications Flash Range 50 cm – 7.0 m (1.6 ft. – 23 ft.) Maximum wide angle (j) 50 cm – 2.3 m (1.6 ft. – 7.5 ft.) Maximum telephoto (i) Shooting Range Maximum Wide Maximum Telephoto Shooting Mode Focusing Range Angle (j) – 3 cm (1.2 in.) – ininity 30 cm (1.0 ft.) – ininity 5 cm (2.0 in.) – ininity 30 cm (1.0 ft.) – ininity 30 cm – 50 cm 3 cm – 50 cm (1.0 ft. – 1.6 ft.) (1.2 in. – 1.6 ft.) 3 cm (1.2 in.) – ininity 30 cm (1.0 ft.) – ininity Other modes 3 cm – 50 cm – (1.2 in. – 1.6 ft.) 1.5 m – 20 m 1.5 m – 20 m (4.9 ft. – 66 ft.) (4.9 ft. – 66 ft.) * Not available in some shooting modes. Continuous Shooting Speed Continuous Shooting Shooting Mode Speed Mode Approx. 2.1 shots/sec. Approx. 0.9 shot/sec. Approx. 0.9 shot/sec. –...
Page 336 Battery Pack NB-5L Type: Rechargeable lithium-ion battery Rated Voltage: 3.7 V DC Rated Capacity: 1120 mAh Charging Cycles: Approx. 300 times Operating Temperature: 0 – 40 °C (32 – 104 °F) Dimensions: 32.0 x 44.9 x 7.9 mm (1.26 x 1.77 x 0.31 in.) Weight: Approx. 25 g (approx. 0.88 oz.) Battery Charger CB-2LX/CB-2LXE Rated Input: 1 00 – 240 V AC (50/60 Hz), 0.085 A (100 V) – 0.05 A (240 V) Rated Output: 4.2 V DC, 0.7 A Charging Time: Approx. 2 hours 5 min. (when using NB-5L) Charge Indicator: Charging: orange / Fully charged: green Operating Temperature: 0 – 40 °C (32 – 104 °F) Dimensions: 57.5 x 81.6 x 21.0 mm (2.26 x 3.21 x 0.83 in.) Weight: C B-2LX: Approx. 65 g (approx. 2.29 oz.) CB-2LXE: A pprox. 59 g (approx. 2.08 oz.) (excluding power cord) • All data is based on tests by Canon. • Camera speciications or appearance are subject to change without notice.
Page 337: Index
Camera access point mode ... 50, 72 Camera shake ........199 CameraWindow AC adapter kit ......279, 285 Display .......... 69 Accessories ........278 Smartphone ........50 Access point CANON iMAGE GATEWAY ....45 Manual settings ......68 Settings ......... 46 Number of display items ....68 Clock............ 93 Adding target device Color Accent (shooting mode) ... 151 Camera ......... 54 Color Swap (shooting mode) ..... 152 Computer ........
Page 338 Index World clock ........264 On ..........193 Slow synchro ....... 194 DC coupler......... 285 Focus bracketing ....... 191 Defaults  Reset all Focus check ........222 DIGITAL CAMERA Solution Disk ... 2 Focusing Digital tele-converter......183 AF frames ........184 Digital zoom ........105 AF lock ........191 Display language ......... 20 AF-point zoom ......130 DPOF .
Page 339 Index Playback  Viewing Device ........... 82 Protecting ........236 Nostalgic (shooting mode) ....144 Indicator ..........93 Interface cable ......... 2, 30 ISO speed.......... 169 Package contents ........2 Photobook set-up ......296 PictBridge ........280, 286 Lamp..........132 Playback  Viewing Portrait (shooting mode) ....137 Poster effect (shooting mode) ... 142 MAC address ........58 Power  AC adapter kit  Battery Macro (focus mode)......181  Battery and charger kit Magniied display .
Page 340 Index SD/SDHC/SDXC memory cards Super slow motion movie  Memory cards (movie mode)........162 Self-timer ........... 107 Super vivid (shooting mode) ....142 2-second self-timer ...... 108 Customizing the self-timer ... 108 Face self-timer Terminal ..... 281, 284, 285, 286 (shooting mode) ......157 Touch Actions .... 49, 53, 55, 63, 248 Wink self-timer Touch AF..........188 (shooting mode) ......155 Sending images ........75 Touch Shutter ........110 Maximum number of images that Toy camera effect (shooting mode) ... 148 can be sent together .....
Page 341 Index Settings ......... 59 Wink self-timer (shooting mode) ..155 Wireless LAN Access point ........56 Security ......... 58 Settings ......... 57 World clock ........264 WPS ............ 64 PBC Method ........64 PIN Method ........66 Wrist strap  Strap Zoom ........22, 96, 105...
Page 342 CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION. Battery Charger CB-2LX IMPORTANT SAFETY INSTRUCTIONS- SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper coniguration for the power outlet, if needed. USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery.
Page 343 FCC Notice (Digital Camera, Model PC1882 systems) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The cable with the ferrite core provided with the digital camera must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Do not make any changes or modiications to the equipment unless otherwise speciied in the manual. If such changes or modiications should be made, you could be required to stop operation of the equipment. Canon U.S.A., Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516) 328-5600 Canadian Radio Interference Regulations This Class B digital apparatus complies with Canadian ICES-003. For CA, USA only Included lithium battery contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
Page 344 Trademark Acknowledgments • The SDXC logo is a trademark of SD-3C, LLC. • This device incorporates exFAT technology licensed from Microsoft. • HDMI, the HDMI logo and High-Deinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. • The iFrame logo and the iFrame symbol are trademarks of Apple Inc. About MPEG-4 Licensing This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4 standard. * Notice displayed in English as required. Disclaimer • Reprinting, transmitting, or storing in a retrieval system any part of this guide without the permission of Canon is prohibited. • Canon reserves the right to change the contents of this guide at any time without prior notice. • Illustrations and screenshots in this guide may differ slightly from the actual equipment. • The above items notwithstanding, Canon accepts no liability for damages due to mistaken operation of the products.

Canon PowerShot S110 User Manual

Quick Links

Related Manuals for Canon PowerShot S110

Summary of Contents for Canon PowerShot S110