Industrial Labeling Systems Ultimate 3000 Series Quick Operator's Manual

Ultimate 3000 series thermal transfer printers

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

ULTIMATE 3000 Series

Thermal Transfer Printers

Quick Operator's Guide

Table of Contents

Need help?

Do you have a question about the Ultimate 3000 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Industrial Labeling Systems Ultimate 3000 Series

Page 1 ULTIMATE 3000 Series Thermal Transfer Printers Quick Operator’s Guide...
Page 3 ULTIMATE 3000 Series The ULTIMATE Printers! The ULTIMATE Printers! This manual is intended for all ULT printers in the ULTIMATE 3000 Series, including the ULT-3320, 3330, 3430, 3460, 3630, 3830...
Page 4: Eu Conformity Declaration
EU - Conformity Declaration We declare herewith that as a result of the manner in which the machine designated below was designed, the type of construction and the machines which, as a result have been brought on to the general market comply with the relevant fundamental regulations of the EU Rules for Safety and Health.
Page 5: Connecting The Printer
Connecting the Printer Connection to Power Supply The printer is equipped with a wide range power unit (100-240V~), so it is possible to use the printer both with a voltage of 230V~/50 Hz and with a voltage of 115V~/60 Hz without making changes to the printer. CAUTION ! Make sure the power switch (6) is in position "...
Page 6: Loading Labels
Loading Labels Figure 2 The following steps are valid for loading labels in tear-off mode. Instructions for loading labels in rewind or dispense mode and for loading fanfold labels can be found in the Printer's Operator Manual or in the documentation of the Present Sensor.
Page 7: Adjustment Of The Printhead Support
Figure 3 8. Slide the media guide ring (7) inward until it lightly touches the side of the media strip. 9. Lower the printhead by rotating the lever (2) counter-clockwise until it locks. 10. When printing narrow label stock, it is necessary to activate the printhead support.
Page 8: Loading Transfer Ribbon
Loading Transfer Ribbon Figure 5 CAUTION ! To avoid premature deterioration of the printhead, make sure the transfer ribbon is slightly wider than the width of label backing. NOTICE ! For direct thermal printing no transfer ribbon is needed ! 1.
Page 9: Adjustment Of The Transfer Ribbon
Adjustment of the Transfer Ribbon Figure 6 In the event that wrinkles appear in the transfer ribbon ( 1), which cause an inconsistent print image, the transfer ribbon shield ( 2) can be adjusted to remove the wrinkles. The adjustment should be done during the printing process.
Page 10: Control Panel
Control Panel The control panel consists of a graphic display (1) and the Navigator Pad (2) with four integrated keys. The control panel display constantly Online provides the operator with realtime information concerning the current printer mode and label processing. The function and operation of the keys depends on the current mode.
Page 11: Functions Of The Control Panel In The Offline Menu
Functions of the Control Panel in the Offline Menu The Offline Menu contains options to set machine and print parameters, to enter test and service functions as well to operate with the memory card. To enter this mode press the key while in the ONLINE mode.
Page 12: Printer Configuration
Printer Configuration There are a variety of parameters that can be set to configure the printer to specific requirements in the "Setup" menu of the Offline Menu. The setup should be performed when operating the printer for the first time and also when basic changes need to be carried out.
Page 13 The following table is an overview about the setup parameters. Further details can be found in the Operator's Manual. Setup Local settings Country Set display language, date and time format Time zone Set Time zone using UTC (Universal Time Coordinated) Daylight saving Select method of daylight saving adjustment Set date...
Page 14: Test Options
Test Options The printer is equipped with several test options, which are summarized in the "Test" menu of the offline menu. 1. Switch from the "Online" mode to the Offline Menu by pressing the key. 2. Press the key or the key until the "Test"...
Page 15 Status Print Sample Figure 8 ASCII Dump Sample Output Label Label commands printed in ASCII Dump mode Figure 9 Figure 10...
Page 16: General Cleaning
Cleaning WARNING ! Before starting any maintenance, power OFF the printer and disconnect the printer from the outlet! General Cleaning During the normal operation of the printer, particles of dust and paper can accumulate inside the printer. Remove these particles with a soft brush or a vacuum.
Page 18 10 Kidder Road, Chelmsford, MA 01824 USA +1-978-250-4414 www.ils-barcode.com Copyright 2005 Industrial Labeling Systems Corp. Specifications subject to change without notification...