Extron electronics DVI 104 Tx Setup Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Extender
  5. DVI 104 Tx
  6. Setup manual

Extron electronics DVI 104 Tx Setup Manual

Dvi extender
Hide thumbs Also See for DVI 104 Tx:
1
2
3
4
5
6

Advertisement

Table of Contents

Setup Guide — DVI 104 Tx/Rx
Description
The Extron DVI 104 Tx and DVI 104 Rx are fiber optic transmitter/
receiver units that extend DVI signals up to 1,640' (500 m) using four
multimode fiber optic cables.
The transmitter plugs directly into the source device
and the receiver plugs directly into the display
device.
The transmitter/receiver pair can handle DVI video
signals with resolutions up to 1920 x 1200 or 1080p
at 60 Hz.
Optional four-fiber multimode cables are available
in varying lengths.

Front panel features

a
Power input — The transmitter and receiver
both have plugs for a 3.5 mm jack to provide
5 VDC to the unit.
The center pin of the jack carries +5 VDC; the
outer shell of the jack is the negative rail.
N
Hi-resolution
Flat Panel Display
with DVI-D Input
If the source device is able to provide 5 VDC on pin 14 of its
DVI output, the transmitter can draw power from the source
device. If the source is a laptop or a PC using a PCI-E graphics
card, it will not be able to provide enough power and the
transmitter must be powered with a separate external power
supply.
The receiver must be powered by an external power supply
through the power input plug.
4 Multi Mode
Fiber
DVI 104
Up to 500 m (1640')
Receiver
PC with DVI Output
DVI 104
Transmitter
1
2
68-1549-50 A
02 09
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DVI 104 Tx and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Extron electronics DVI 104 Tx

Summary of Contents for Extron electronics DVI 104 Tx

  • Page 1: Front Panel Features

    Setup Guide — DVI 104 Tx/Rx Description The Extron DVI 104 Tx and DVI 104 Rx are fiber optic transmitter/ receiver units that extend DVI signals up to 1,640' (500 m) using four multimode fiber optic cables. The transmitter plugs directly into the source device and the receiver plugs directly into the display device.

  • Page 2: Top Panel Features

    Setup Guide — DVI 104 Tx/Rx, (cont’d) LC Jacks — Four fiber optic cables connect the transmitter to the receiver. The cables connect to the four female LC jacks in each of the units. A label on the top panel identifies the unit as the transmitter or receiver and identifies the fiber optic port numbers and the power input.

  • Page 3: Setup And Operation

    Setup and Operation When using the DVI 104 Tx/Rx for the first time or if the display device is changed, it is essential to set up the EDID Minder. The setup process places EDID information on a EEPROM chip in the transmitter, which allows the video source to boot up correctly.
  • Page 4 Ensure that the display device is still powered on, connect the receiver directly to the DVI input, and tighten the thumbscrews. Ensure that the PC or source is powered off, connect the transmitter directly to the source’s DVI input, and tighten the thumbscrews.

  • Page 5: Troubleshooting

    Ensure that the correct EDID information has been stored on the transmitter’s EDID Minder. When using the DVI 104 Tx/Rx for the first time or if the display device is changed, it is essential to set up the EDID Minder as described in steps 1-6 of “Setup and Operation”...
  • Page 6 Inside Europe Only Inside Asia Only +81.3.3511.7656 FAX Inside China Only +971.4.2991880 FAX Inside USA / Canada Only +1.919.863.1794 +31.33.453.4040 +65.6383.4400 +86.21.3760.1568 +1.714.491.1500 +1.919.863.1797 FAX +31.33.453.4050 FAX +65.6383.4664 FAX +86.21.3760.1566 FAX +1.714.491.1517 FAX © 2009 Extron Electronics. All rights reserved.

This manual is also suitable for:

Dvi 104 rx

Table of Contents