Summary of Contents for Extron electronics DTP DVI 4K 330
Page 1
User Guide HDMI & DVI Extenders DTP DVI 4K 330 DVI Twisted Pair Extender 68-2342-01 Rev. C 02 23...
Page 2
Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended...
Page 4
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Mounting the Transmitter or Receiver ....10 Tabletop Use ..........10 Mounting kits ..........10 UL Rack-Mounting Guidelines ....... 11 Consignes UL pour le montage en rack ..11 Disconnecting the Ground ......... 12 Contents DTP DVI 4K 330 Transmitter and Receiver •...
Page 7
Contents DTP DVI 4K 330 Transmitter and Receiver •...
This guide describes the Extron DTP DVI 330 Long Distance Digital Visual Interface (DVI) Twisted Pair Extender, which consists of a DTP DVI 4K 330 transmitter and a DTP DVI 4K 330 receiver. This guide describes how to install, operate, and configure the transmitter and receiver.
The DTP DVI 4K 330 Tx/Rx units are housed in quarter rack width metal enclosures. They can be set on a tabletop or mounted in a rack, under or through furniture. The receiver can also be mounted on a projector bracket.
In a system where the local output is not used, ensure that you power up the end display first before the video source. Route the DDC to the remote end (see the DDC Route switch [see on page 9]). DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
Page 11
If you have removed the ground jumpers (see on page 12) because of ground potential differences, one DTP DVI 330 unit cannot remotely power the other unit. Each unit requires a local power supply. DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
Do not connect the sleeves to the negative (-) contacts. ATTENTION : Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs (–). DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the transmitter and receiver. The DTP DVI 330 Tx/Rx does not work properly with these cables. DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
Page 14
Figure 6 shows how to wire the connector. Use the supplied tie-wrap to strap the power cord to the extended tail of the connector. Smooth Ridges SECTION A–A Power Supply Tie Wrap Captive Screw Output Cord Connector Figure 6. Power Connector Wiring DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
Page 15
To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter. DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
If the other devices are not turned on before the video source, the image may not appear. DTP DVI 4K 330 Transmitter and Receiver • Installation and Operation...
Mount the unit using any optional compatible mounting kit listed on the Extron website (www.extron.com), in accordance with the directions included with the kit. For rack mounting, see UL Rack-Mounting Guidelines on the next page. DTP DVI 4K 330 Transmitter and Receiver • Reference Information...
Mise à la terre — Assurez-vous que l’équipement est correctement mis à la terre. Accordez une attention particulière aux connexions électriques autres que les connexions directes au circuit de dérivation (ex. : les multiprises). DTP DVI 4K 330 Transmitter and Receiver • Reference Information...
Figure 9. Opening the Transmitter and Receiver Locate, lift off, and discard jumpers JMP2 and JMP3 from both units (see figure 10). JMP2 JMP3 JMP2 JMP3 Transmitter Receiver Figure 10. Jumper Locations DTP DVI 4K 330 Transmitter and Receiver • Reference Information...
Page 20
Obtain a second 12 V power supply (one supply is provided with the transmitter and normally powers both units), and locally power both units (see Power supply wiring on page 7). DTP DVI 4K 330 Transmitter and Receiver • Reference Information...
Page 21
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.