moving parts. Loose clothes, jewelry
or long hair can be caught in moving
g) if devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
4) power tool use and care
a) do not force the power tool. use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d) store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
e) Maintain power tools. check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
5) Battery tool use and care
a) recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
b) use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
c) when battery pack is not in use,
keep it away from other metal
objects like paper clips, coins,
keys, nails, screws, or other small
metal objects that can make a
connection from one terminal
to another. Shorting the battery
terminals together may cause burns
or a fire.
d) under abusive conditions, liquid
may be ejected from the battery,
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This
will ensure at the safety of the power
tool is maintained.
read all instructions
cHain saw safety
• keep all parts of the body away from
the saw chain when the chain saw is
operating. Before you start the chain
saw, make sure the saw chain is not
contacting anything. A moment of
inattention while operating chain saws
may cause entanglement of your clothing
or body with the saw chain.
• always hold the chain saw with your
right hand on the rear handle and
your left hand on the front handle.
Holding the chain saw with a reversed
hand configuration increases the risk of
personal injury and should never be done.
• Hold the power tool by insulated
gripping surfaces only, because the
saw chain may contact hidden wiring.
Saw chains contacting a "live" wire may
make exposed metal parts of the power
tool "live" and could give the operator an
• Wear safety glasses and hearing
protection. further protective
equipment for head, hands, legs
and feet is recommended. Adequate
protective clothing will reduce personal
injury by ﬂying debris or accidental
contact with the saw chain.
• Do not operate a chain saw in a tree.
Operation of a chain saw while up in a
tree may result in personal injury.
• Always keep proper footing and
operate the chain saw only when
standing on ﬁxed, secure and level
surface. Slippery or unstable surfaces
such as ladders may cause a loss of
balance or control of the chain saw.
• When cutting a limb that is under
tension be alert for spring back. When
the tension in the wood ﬁbers is released
the spring loaded limb may strike the
operator and/or throw the chain saw out