Download Print this page

Clicker 321 Operation Manual

Hide thumbs

Advertisement

Quick Links

CLICKER 321
Your Clicker remote can be programmed to operate
with different brands of garage door openers.
Compatible with most garage door opener systems
manufactured by Chamberlain, Genie, LiftMaster,
Linear, Master Mechanic, Moore-O-Matic, Multi-
Code, Sears, Stanley, and DoIt.
THE CLICKER IS NOT COMPATIBLE WITH GENIE
INTELLICODE, STANLEY SECURE CODE, OR
SECURITY✚ GARAGE DOOR OPENER SYSTEMS.
The Clicker remote can be programmed to operate
up to 3 garage door openers or gates, including
different brands. All programming is done using the
3 buttons on the Clicker.
IDENTIFY YOUR GARAGE DOOR OPENER BRAND
Determine your brand from an original hand held remote or locate the motor unit receiver.
The receiver can be mounted on the back panel of the motor unit or could be mounted on the wall.
SECTION
BRAND
1
Stanley
2
Multi-Code
3
4
Chamberlain, LiftMaster, Sears,
Master Mechanic, DoIt
5
Genie (9 Code Switches)
6
Genie (12 Code Switches)
1 Stanley • 2 Multi-Code
Locate your systems code switch positions from an original hand held remote or the motor unit receiver.
If the switch is "on" or "up", place a 1 in the corresponding box in the TABLE below. If the switch is "off" or "down",
place a 3 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
PROGRAMMING
Before you begin programming the Clicker, select which button you want to operate
your garage door opener. After completing a step, you have 15 seconds to proceed
to the next step.
Step 1: Press the 1st and 3rd buttons down simultaneously and hold until the red
indicator starts to blink. Release both buttons. Wait for the red indicator to
stop blinking.
Step 2: Press the button you want to operate your garage door opener: Stanley press the button 1 time; Multi-Code
press the button 2 times. Wait for the red indicator to blink the same number of times.
Step 3: Using the code switch sequence from the table above, press and release the button that corresponds with
the number in each column until the entire code has been entered into the Clicker. Immediately after the code is
entered, the indicator light will blink (once for Stanley; twice for Multi-Code).
Programming is complete. To test press the button you selected to activate the garage door.
If programming is unsuccessful, reverse code from TABLE above.
(Change 1 to 3; 3 to 1) Stanley brands – try as Multi-Code.
Multi-Code brands – try as Stanley Repeat Steps 1-3 above.
Note: To program additional doors, proceed to appropriate section using another button in step 2.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with
remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross path of
moving gate or door.
1 2 3 4 5 6 7 8 9 10
WARNING
CAUTION
Remote Control
proceed to the
appropriate
Motor
Unit &
Receiver
Wall Mounted
Control
Circle your
Brand and
section.
Step 1
Step 2
Step 3

Advertisement

loading

  Related Manuals for Clicker 321

  Summary of Contents for Clicker 321

  • Page 1 Step 3: Using the code switch sequence from the table above, press and release the button that corresponds with the number in each column until the entire code has been entered into the Clicker. Immediately after the code is entered, the indicator light will blink (once for Stanley; twice for Multi-Code).
  • Page 2 Step 3: Using the code switch sequence from the table above, press and release the button that corresponds with the number in each column until the entire code has been entered into the Clicker. Immediately after the code is entered, the indicator light will blink 3 times.
  • Page 3 Step 4: Press and release smart-learn button on motor unit. (Indicator light next to the smart-learn button should turn on.) Press and hold the Clicker button you selected until the motor unit lights blink. If light bulbs are not installed, two clicks will be heard.
  • Page 4 Paso 3: Utilizando la secuencia del código del interruptor de la tabla que aparece arriba, oprima y suelte el botón que corresponda al número anotado en cada columna, hasta que haya ingresado todo el código al Clicker. Inmediatamente después de ingresar el código, la luz del indicador parpadea (una vez para el Stanley y dos veces para el Multi-Code).
  • Page 5 Apagado/ hacia abajo (Off/down) Paso 1 PROGRAMACIÓN Antes de empezar a programar el Clicker, seleccione el botón que desee usar para operar su abridor de Paso 2 puerta de cochera. Una vez terminado cada paso, tiene 15 segundos para proceder al paso siguiente.
  • Page 6 CAMBIO DE PILAS Las pilas de litio que vienen con el Clicker le deben durar de 3 a 5 años en condiciones de uso normales, usando el abridor 6 veces al día. Si observa con frecuencia que el alcance del control remoto es corto, la operación es intermitente, o bien la luz del indicador rojo está...