CLICKER CLT1 - Universal Garage Door Opener Remote Control Manual

INTRODUCTION

The Clicker remote can be programmed to operate up to 2 garage door openers or gates, including different brands. All programming is done using the:

• Brand switches
• Remote control DIP switches
• Remote control push buttons A and B, and LED indicator

BUTTONS AND PARTS

BRAND Switches

UP position is ON
DOWN position is OFF

DIP Switches

UP position is ON
DOWN position is OFF

NOTE: Use pen or small screwdriver to move dip switches.

PREPARATION

Determine the BRAND of the existing garage door opener or handheld remote controls. If all remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the external receiver near the flexible wire antenna. Also determine if your motor unit/receiver system has DIP switches or a smart-learn button. (Some models require removing the light lens.) Proceed to Step 1 for your specific BRAND switch. For further information consult your garage door opener manual.

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Step 1 - Set Brand Switch

• Set brand switches on Clicker remote. Refer to Table 1.

Table 1 (Brand Switches)

NOTE:

• Some garage door openers use wire connectors instead of DIPswitches. If wire is present it is "ON". If wire is absent or cut it is "OFF". Consult your garage door opener manual for further information.
• If you have a unit with Yellow, White or Gray Smart-Learnbutton and you do not have a remote, set the first 9 dip switches to your choice. The remaining 10-12 should be set to off. Proceed to Step 3.

Step 2 - Set Clicker Dip Switches

Open existing remote to expose code switches or obtain the switch settings from your receiver.

Match the Clicker's DIP switches to already existing receiver/remote DIP switches. Set extra DIP switches in the Clicker remote to the off position.

NOTE: For Chamberlain/Sears/LiftMaster/Master Mechanic. If the receiver/remote DIP switch has three positions labeled "+", "0" and "-" do not use the "0" position (if you have a three button remote #1 switch must be set to "-" for the large button to work). Reprogram existing receiver and remote(s) using "+" and "-".

Match existing DIP switches. Remaining switches are off.

NOTE: Make sure all existing remotes operate correctly before programming.

Step 3 - Programming the Desired Clicker Push Button

Press and hold both buttons until LED begins to flash. When LED flashes, release both buttons and immediately press the button that you want to activate the door and release.

Your clicker is now programmed, proceed to Step 4 or 5.

• For Chamberlain/Sears/LiftMaster/Master Mechanic. If your garage door opener has a Smart-Learn button, continue on to Step 4.
• For all other types continue to Step 5.

Step 4 - For Smart-Learn Button Programming ONLY

1. Press and release Smart-Learn button.
   
2. Press and hold button selected in Step 3 for 3 seconds.
   

NOTE: If you have a Chamberlain, Sears, Liftmaster, Master Mechanic or Do It motor unit/receiver with a Yellow, White or Gray Smart-Learn button it will activate immediately upon successful programming. If your motor unit/receiver has a Green, Orange or Red Smart-Learn button, the light bulb will blink signifying it has learned the Clicker remote control code.

Step 5 - Programming is Complete

Programming is complete, to test, press the button selected to activate garage door.

NOTE: For Genie, Stanley, Multi-Code and Linear/Moore-O-Matic. If Programming does not work review brand and dip settings and repeat step 3 thru 5. Also try reversing the dip switch settings (Turn ON to OFF and OFF to ON).

NOTE: If programming to more than one motor unit; after successfully programming button "A", determine the brand of the second garage door opener. Follow the instructions pertaining to that particular brand to program button "B". Programming a different code into button "B" will not affect button "A". The codes and brand switch settings are retained within their specific Clicker button.

REMOTE CONTROL BATTERY

When the remote range is diminished, operation is intermittent, or the LED dims, replace the battery. Memory is not lost when the battery is removed.

NOTE: Dispose of old batteries properly.

TECHNICAL SUPPORT

www.clickerproducts.com

800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM; SUNDAY 8AM-4:30PM)

Documents / Resources

References

• Clickerproducts.com

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download CLICKER CLT1 - Universal Garage Door Opener Remote Control Manual