CLICKER KLIK1U - Universal Garage Door Opener Remote Control Manual

Also See for KLIK1U:

Instructions (4 pages)

Table of Contents

Contents

1 USING THE DEVICE
2 SMART/LEARN BUTTON
3 DIP SWITCH
4 WARNING
5 Product Registration and Troubleshooting
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

CLICKER KLIK1U - Universal Garage Door Opener Remote Control Manual

USING THE DEVICE

Device Overview
NOTE: You opener may appear different and you may have to remove the light lens to access the learn button.

Start with garage door closed. Identify garage door opener type - Smart/Learn button or DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or external receiver.
Clicker products are intended to be used only with garage door openers manufactured after 1993 that utilize photo-eyes safety sensors. These are always located on or near the bottom of the door track. If your garage door does not have the sensors attached and working, the opener is not compliant with current federal safety regulations and should be replaced.
Proceed with instructions according to your type of garage door opener.

* NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with Chamberlain technology.
**NOTE: Visit www.clickerproducts.com for Genie Intellicode II instructions

SMART/LEARN BUTTON

CHART A
# of times to press button	Brand	Type/Color of Smart/Learn	Year
1	Linear	Mega-Code	'97-Current
2	Chamberlain *	Orange/Red	'97-'03
3	Chamberlain *	Purple	'05-Current
4	Chamberlain *	Green	'93-'96
5	Genie Overhead Door	Intellicode	'95-Current
6	Genie ** Overhead Door	Intellicode	'93-Current
7	Stanley	Secure Code	'98
8	Chamberlain *	Yellow	'11-Current
9	Wayne Dalton	Rolling Code	'99
11	Chamberlain	9 Position	'90-'92

See Chart A to determine # of times to press button and write in blank on Step 5.
Press program button until LED lights.
Press and release the Smart/ Learn button.
Select a button to program. Press button times ensuring LED stops flashing after each press. Code is accepted when one of the following occurs:

NOTE: If there are problems programming to button 1, program to button 2.
Press program button.
Programming complete. Press selected button to test. If unit does not work, return to Step 3.

DIP SWITCH

CHART B
# of times to press button	Brand	Description	Year
11	Chamberlain *	9 Position	'90-'92
12	Chamberlain *	9 Position Canada	'83-'89
13	Genie	12 Position	'85
14	Linear Multicode	10 Position	'76
15	Chamberlain	8 Position	'83-'89
16	Stanley/ Multicode	10 Position	'76
17	Genie	9 Position	'85
18	Linear Moore-O-Matic	8 Position	'76
19	Chamberlain	7 Position	'83-'89

See Chart B to determine # of times to press button and write in blank on Step 5.
Match DIP switches. Turn extra switches OFF.**
Press program button until LED lights.
Select a button to program. Press button times ensuring LED stops flashing after each press. Code is accepted when door activates.
Press program button.
Programming complete. Press selected button to test. If unit does not work, return to Step 3.

NOTE:
2 Position DIP Switch:
If programming fails reverse DIP switches (OFF to ON and ON to OFF).

** 3 Position DIP Switch:
For Chamberlain remotes DO NOT use the "0" position, use "+" or "-". If you already have a 3-button remote, DIP switch #1 must be set to "-" if the large button is to open the door. It may be necessary to reprogram original remote controls.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

REMOTE CONTROL BATTERY

To prevent possible SERIOUS INJURY or DEATH:

NEVER allow small children near batteries.
If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

Replace ONLY with 3V2032 coin batteries.
DO NOT recharge, disassemble, heat above 100°C (212°F) or incinerate.

Dispose of batteries properly. Replace ONLY with 3V2032 coin batteries.

Product Registration and Troubleshooting

www.clickerproducts.com • 1-800-442-1255

Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie and Intellicode are trademarks of GMI Holdings, Inc. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.