Subscribe to Our Youtube Channel
Related Manuals for Technibel HKE 189R5I
Summary of Contents for Technibel HKE 189R5I
-
Page 1: Installation Manual
HKE 189R5I HKE 259R57I HKE 369R57I HKE 489R57I HKE 609R57I HKE 709R7I INSTALLATION MANUAL HKE 909R7I Inverter split air to water heat pump - Indoor unit Pub. ??.????.???.? -
Page 2: Water System Drawing
• Connect all wiring tightly. Loose wiring may cause overheating IMPORTANT! at connection points and a possible fire hazard. Please read before installation • Do not allow wiring to touch the refrigerant tubing, This air conditioning system meets strict safety and compressor, or any moving parts of the fan. -
Page 3: Table Of Contents
- Water system drawing ....... 2 NOTE 1 - Only the following indoor units are to be used with the outdoor units indicated below: Indoor units Outdoor units HKE 189R5I ----> GRFP 189R5I HKE 259R57I ---->... -
Page 4: Presentation
• Reminder: - Water system pressure: 2 bar. - Operating limits: Heating mode Heating mode Cooling mode Water output Water output Water output temperature (°C) temperature (°C) temperature (°C) Outdoor dry air Outdoor dry air Outdoor dry air temperature (°C) temperature (°C) temperature (°C) 35 43... - Page 5 2.1.2 - ELECTRICAL BOX 1 - Electrical cable passage. 2 - Terminal strip. 3 - Heating element circuit breakers. 4 - Heating element contactors. 5 - Circulator contactors. 6 - Fault relays. 7 - Water flow rate relay. 8 - Heating control board. 9 - Communication module CC1.
-
Page 6: Dimensions And Weight
2.2 - DIMENSIONS AND WEIGHT HKE 909R 189R 259R 369R/489R/609R 709R Water inlet connection 3/4” male 3/4” male 1” male 1”1/4 male 1”1/4 male Water outlet connection 3/4” male 3/4” male 1” male 1”1/4 male 1”1/4 male Water circuit fill / drain 1/2”... -
Page 7: Installation
3 - INSTALLATION 3.1 - LOCATION Minimum clearance in front of the unit: 1 m • Protection index of the unit: IP 21. • Select the location for the unit on the basis of the following criteria: - the unit must be installed in a sheltered location, - the unit must not be installed near the following: 0 . -
Page 8: Temperature Sensor
• Replacing the cover. - Present the cover on the unit while aligning the lower edge with the lower part of the rear support. - Fit the cover against the rear support to engage the hooks in the notches (1). - Slide the cover downward fully into place (2). -
Page 9: Connections
4 - CONNECTIONS 4.1 - REFRIGERATION CONNECTIONS APPLIANCES FILLED WITH R 410 A R 410 A 3 - In the case of a new charge: • R 410 A is a high-pressure refrigerant (+ 50% in relation to - the charge must be undertaken in liquid phase, R 22 and R 407 C). -
Page 10: Hydraulic Connection
• For the following information: - Maximum height between units. - Required tools. - Advice concerning the piping installation. - Connection to the outdoor unit. - Leak testing. - Vacuum operation. - Additional refrigerant charge. Refer to the installation instructions provided with the outdoor unit. •... - Page 11 Single-phase power supply Single-phase power supply 230V / 1+T / 50Hz 400V / 3+N+T / 50Hz Remove the jumper PE N Ph PE N Ph PE N Ph1 Ph2 Ph3 Jumper Terminal Terminal Terminal strip XA strip XA strip XA SPW-W186/256/366/486/606 SPW-W366/486/606 SPW-W706/906...
- Page 12 Note 2: The sizing of the power supply cables is to be ensured by the installer in accordance with the installation conditions and as per current standards. Cable sizes, indicated below, are given for information purposes. They are calculated in accordance with NFC 15-100 (≈ CEI 364) with the following hypotheses: - Maximum current, see table below.
- Page 13 4.3.2.2 - 400 V three-phase power supply • Provide a common power supply for both the outdoor unit and the indoor unit. • The indoor unit power cable is connected to the outdoor unit's terminal strip. See diagram below. Note: the indoor unit's power cable must be the same size as the general power supply cable. Single-phase power supply 400 V / 3 + N + T / 50 Hz N Ph1 Ph2 Ph3...
- Page 14 4.3.4 - OTHER CONTROL CONNECTIONS Caution: To avoid problems related to electromagnetic disturbances, do not route these cables near power cables. Control unit With built-in ambient temperature sensor. To be installed in zone 1. Outside air temperature Load shedding (if installed) Installation Installation Outdoor unit...
- Page 15 F) ECO signal for remote controls (if installed) - In order to send reduced mode orders (Eco or standby) to the terminal unit remote control units in the case of applications such as 1 terminal unit zone or 2 mixed zones. - In the form of a potential-free contact which can used in VLV (Very Low Voltage), 2 A max.
-
Page 16: Accessories
4.3.5 - MAINTENANCE KEYPAD / DISPLAY UNIT CONNECTION • A specific keypad / display unit can be connected for maintenance and troubleshooting operations. See maintenance manual. Terminal XB Note: of the indoor unit This keypad / display unit must not be used for the installation's normal operation. - Page 17 • Water quality: - In order for the heat pump to operate under good conditions and provide optimum performance, it is essential to ensure that the system’s water circuit is clean. If the water circuit becomes clogged, this will significantly affect the machine’s performance.
- Page 18 6.2.2 - MODULE CC1 CONFIGURATION • The communication and control module manage the circulator and the communication interface between the system and the generator. Micro-switches It is equipped with 2 micro-switches, No. 1 and No. 2. No. 1 and No. 2 Micro-switch No.
-
Page 19: Maintenance Instruction
6.3.4 - SHUTDOWN FORCED CIRCULATOR OPERATION • Press and hold the button for 5 seconds. The circulator stops. O” flow rate light do out. The circulator indicator light and the “H 6.4 - OPERATION • Installation power is ON. • Start the system in the desired operating mode using the control box button (consult the system control manual and the control box user's guide). -
Page 20: Wiring Diagram
• If tripped: - Turn off and lock out the unit. - Correct the fault. - Reset the circuit breaker. Note: The opening of circuit breaker Q4 disconnects only the control part. In the event of maintenance / servicing, all circuits must be disconnected by opening the main circuit breaker. - Page 21 ELECTRICAL DIAGRAM - HKE 189R / 259R / 369R / 489R / 609R / 10 05 855 - 00 709R / 909R - 230 / 1 / 50 - 400 / 3 N / 50 230V...
- Page 22 How to Install the Outdoor Unit Installing the Outdoor Unit For 3 HP unit (3-phase) l a i 0 1 1 and ensure good drainage. , y l 4- ø32 drain pipe is used, or for use in cold-weather regions, Air Intake ensure a height of 15 cm or more at the feet on both sides of the unit.
- Page 23 Electrical Wiring General Precautions on Wiring (7) Regulations on wire diameters di er from locality to as shown on its nameplate, then carry out the wiring closely following the wiring diagram. LOCAL ELECTRICAL CODES before beginning. You must ensure that installation complies with all (2) Provide a power outlet to be used exclusively for relevant rules and regulations.
- Page 27 polarenergi.no P.boks 117, 9450 Hamnvik...
Need help?
Do you have a question about the HKE 189R5I and is the answer not in the manual?
Questions and answers