Related Manuals for Kingston Technology KNS500/WG
Summary of Contents for Kingston Technology KNS500/WG
- Page 1 INGSTON ECHNOLOGY ORT & 10/100TX W ORKGROUP THERNET WITCH SER’S UIDE : KNS500/WG ODEL(S) KNS800/WG...
- Page 2 Kingston Technology’s Fast EtheRx 5-Port & 8-Port 10/100TX Workgroup Fast Ethernet Switch User’s Guide Part No. 4460074-001.B01 Kingston Technology Company 17600 Newhope Fountain Valley, CA 92708 (714) 435-2600 http://www.kingston.com KNS800/WG User’s Guide - Rev. B01 Kingston Technology Company...
-
Page 3: Table Of Contents
Link / Activity LED... 6 Full Duplex and Collision LED... 6 Cascade Switch... 6 Notes on MDI and MDI-X ... 7 Rear Panel... 8 Power Connector... 8 10/100TX UTP Ports ... 8 Kingston Technology Company ABLE ONTENTS KNS800/WG User’s Guide – Rev.B01... - Page 4 Duration of Warranty...18 Free Technical Support ...19 Disclaimers ...19 F.C.C. Certification ...20 CE Notice...20 C-Tick Certification ...20 KNS800/WG User’s Guide - Rev. B01 Pin Assignments...10 Cabling Guidelines ...11 Specifications ...14 Frequently Asked Questions...16 Warranties and Notices ...18 Kingston Technology Company...
-
Page 5: Introduction
Congratulations on the purchase of your new Kingston Fast EtheRx 10/100TX Workgroup Fast Ethernet Switch. There are two models: the KNS500/WG and KNS800/WG, 5-port and 8-port Workgroup Fast Ethernet Switch, respectively. The Fast EtheRx 10/100TX Workgroup Fast Ethernet Switch offers five (5) or... -
Page 6: Model Types
Fast Ethernet Switch FDX / COLL KNS500/WG 10/100TX Wo r k g r o u p Fast Ethernet Switch LINK / ACT FDX / COLL KNS800/WG Kingston Technology Company Fast EtheRx Switch 100TX CASCADE Model KNS500/WG Fast EtheRx Switch 100TX Model KNS800/WG KNS800/WG User’s Guide –... -
Page 7: Special Features
Conforms to IEEE 802.3u 100BASE-TX, IEEE 802.3i 10BASE-T, and IEEE 802.3 CSMA/CD Ethernet Standards Package Contents Your Fast EtheRx Switch package should contain the following items: ‰ Fast EtheRx KNS500/WG or KNS800/WG Workgroup Fast Ethernet Switch ‰ External power adapter (KNS500/WG) ‰... -
Page 8: Design Features
The Fast EtheRx Switch uses a packet-forwarding method called Store-and- Forward, which minimizes the re-transmission of faulty data packets. This means that the Fast EtheRx Switch can store the incoming frame in an internal buffer and check the packet for errors before sending it out to the destination port. -
Page 9: Hardware Installation
KNS800/WG Front Panel Power LED The PWR LED indicates the power status of the Fast EtheRx Switch. The LED will light up steady green when the AC power cord is connected to the unit from a power source. 100TX Speed Detection LED The 100TX LED will automatically light up when 100Mbps operation is detected. -
Page 10: Link / Activity Led
Cascade Switch The cascade position marked “ KNS500/WG or port 8 on the KNS800/WG) as internally-crossed like all other UTP ports. By default, all repeater and switched UTP ports are generally configured as standard MDI-X, or internally-crossed ports. With a straight- through cable, this port can be used for cascading to a standard MDI device, such as a network adapter or router. -
Page 11: Notes On Mdi And Mdi-X
MDI-X port, which implements the crossover internally. Port 1 through port 4 on the KNS500/WG, and port 1 through port 7 on the KNS800/WG, like all normal hub ports, are configured MDI-X. The last UTP port, port 5 on the KNS500/WG, or port 8 on the KNS800/WG, supports both port configurations, MDI and MDI-X. -
Page 12: Rear Panel
100BASE-TX or 10BASE-T connections and half- or full-duplex mode operation. All ports, like all normal switch ports, are generally configured as MDI-X. However, the last UTP port (port 5 on the KNS500/WG or port 8 on the KNS800/WG) supports both MDI-X and MDI port configuration. Please refer to Cascade Switch on page 6. -
Page 13: Appendices
Appendices KNS800/WG User’s Guide - Rev. B01 Kingston Technology Company... -
Page 14: Appendix A Pin Assignments
By default, all repeating and switched UTP ports are generally configured as MDI-X, unless otherwise specified. The last UTP port (port 5 on the KNS500/WG and port 8 on the KNS800/WG) is linked to a cascade switch that allows it to support UTP cabling in the straight-through (MDI) and crossover (MDI-X) wiring configuration. -
Page 15: Appendix B Cabling Guidelines
8-Pin RJ-45 CAT 5 only Pin Number 1 (TRX+) 2 (TRX-) 3 (RCV+) 6 (RCV-) 4, 5, 7, 8 Table B-3. Cross-Over Wiring 100BASE-TX UTP CAT 5 "Cross-Over” Configuration Pin Number 3 (RCV+) 6 (RCV-) 1 (TRX+) 2 (TRX-) Not Used Kingston Technology Company... -
Page 16: Utp Cable Wiring Standards
Pin 6 Pair 2 Yellow Pin 7 Pair 4 Brown Pin 8 Pair 4 White Table. B-4 4-Pair T568A Wiring Kingston Technology Company Appendix B Fig. B-2 4-Pair T568B Wiring Solid T568B White/Green Pin 1 Green/White Pin 2 White/Orange Pin 3... -
Page 17: Utp Cable Rating Codes
NEAR-END CROSSTALK (NEXT) – In wires packed together within a cable, the signals generated at one end of the link can flush out the weaker signals coming back from the recipient. KNS800/WG User’s Guide - Rev. B01 Kingston Technology Company... -
Page 18: Appendix C Specifications
Appendix C Fast EtheRx Model KNS500/WG Compliance: Media Interface: Uplink Port: 10BASE-T /100BASE-TX: Half / Full-duplex mode: Diagnostic LEDs: Switching Approach: Flow Control: Half Duplex: Full Duplex: MAC Address Support: Filtering/Forwarding Rate (min. packet size 64 bytes): Latency (min. packet size 64... -
Page 19: Appendix C Specifications
100VAC – 240VAC, 50/60Hz, external auto-sensing power supply 5VDC/3A 9.8 Watts maximum 1.1” x 6.5” x 6.1” (28mm x 165mm x 155mm) 2 lbs. (0.9 kg) FCC Class A, CE CISPR A, C-Tick EN55022, IEC801-2, IEC801-3, IEC801-4 EN60950 Kingston Technology Company... -
Page 20: Appendix D Frequently Asked Questions
Ethernet packets. It repeats incoming signals to all other ports on the device. Like a repeater, a switch can also extend the diameter of a network. However, a switch can also extend the collision domain of a network, like bridging a 10Mbps Ethernet LAN with a 100Mbps Fast Ethernet LAN. - Page 21 Can a Four-Pair CAT 5 cable support two 100BASE-TX devices? Although only two pairs are used in the standard four-pair CAT 5 UTP cable, it is not recommended because it exceeds the specifications outlined by IEEE 802.3u. KNS800/WG User’s Guide - Rev. B01 Kingston Technology Company...
-
Page 22: Appendix E Warranties And Notices
Appendix E Warranties and Notices Limited Warranty Statement KINGSTON TECHNOLOGY COMPANY ("Kingston") warrants that this product is free from defects in material and workmanship. Subject to the conditions and limitations set forth below, Kingston will, at its option, either repair or replace any part of this product which proves defective by reason of improper workmanship or materials. -
Page 23: Free Technical Support
Rev. 3/99 Copyright © 1999 Kingston Technology Company. All rights reserved. Printed in Taiwan. Kingston Technology and the Kingston logo are trademarks of Kingston Technology Company. All other logos and trademarks are properties of their respective companies. KNS800/WG User’s Guide - Rev. B01... -
Page 24: F.c.c. Certification
CE Notice The official CE symbol indicates compliance of this Kingston Technology product to the EMC directive of the European Community. The CE symbol indicates that this Kingston product meets or exceeds the following standards: ‰...