Extron electronics RGB-DVI 300 Setup Manual
Video scalers and converters
Hide thumbs
Also See for RGB-DVI 300:
- User manual (68 pages) ,
- Specifications (2 pages) ,
- Setup instructions (2 pages)
Advertisement
Quick Links
RGB-DVI 300 and RGB-HDMI 300 (A) Setup Guide
RGB-HDMI 300 A
CONFIG
Front Panel
POWER
INPUT
12V
1.0A MAX
RGB/R-Y,Y,B-Y
Rear Panel
RGB-DVI 300
CONFIG
Front Panel
POWER
12V
RGB/ R-Y, Y, B-Y INPUT
1.0A MAX
Rear Panel
CAUTION:
Installation and service must be performed by authorized personnel only.
Unless otherwise stated, these instructions apply to both the RGB-DVI 300 and the RGB-HDMI 300 (A) video scalers and
converters. These instructions provide a quick setup guide for experienced installers.
Step 1 — Power Off
Turn all the equipment off and disconnect all cables.
Step 2 — Mounting
Mount the unit in a convenient location, in a rack, behind a display, under a desk, or through a desk.
Step 3 — Connect Video and Audio Input
Connect an analog RGB or HDTV YUV video input to the 15-pin female VGA connector. Connect an analog audio source to
the 3.5 mm TRS connector (RGB-HDMI 300 A only).
Step 4 — Connect Display Device
Connect the unit to a digital display using a HDMI connector for the RGB-HDMI 300 (A) or a DVI-I connector for the
RGB-DVI 300.
NOTE:
The RGB-DVI 300 only outputs a DVI-D signal, although a DVI-I connector is used for greater installation
flexibility.
A display is required to control the RGB-DVI 300 or RGB-HDMI 300 (A) using the menu and on-screen display.
Step 5 — Connect and Apply Power
Connect the 12 VDC external power supply (provided) to the 3.5 mm, two-pole, captive screw Power input connector. Apply
power to the RGB-DVI 300 or RGB-HDMI 300 (A) power supply. Then power on the display and power on the video source.
Step 6 — Configure System
Configure the system via the front panel controls and on-screen display, Simple Instruction Set
the Signal Processing Products Control Program. (See the RGB-DVI 300 and RGB-HDMI 300 (A) User Guide for complete
instructions.)
MENU
ENTER
AUDIO
RGB - HDMI 300 A
MENU
ENTER
DVI-D OUTPUT
RGB - DVI 300
ADJUST
RGB - HDMI 300 A
RS-232
Tx Rx
HDMI OUTPUT
ADJUST
RGB - DVI 300
RS-232
Tx Rx
(SIS
) commands, or
™
™
Advertisement
Related Manuals for Extron electronics RGB-DVI 300
Summary of Contents for Extron electronics RGB-DVI 300
- Page 1 RGB-DVI 300 and RGB-HDMI 300 (A) Setup Guide RGB-HDMI 300 A ADJUST CONFIG MENU ENTER RGB - HDMI 300 A Front Panel POWER INPUT 1.0A MAX RS-232 Tx Rx RGB/R-Y,Y,B-Y AUDIO HDMI OUTPUT RGB - HDMI 300 A Rear Panel...
-
Page 2: Front Panel Controls
RGB-DVI 300 and RGB-HDMI 300 (A) Setup Guide (Continued) NOTE: If no video output is visible on the display, the output rate of the scaler can be toggled between 1024 x 768 at 60 Hz and 720p at 60 Hz, without needing the on-screen menu. Hold the Menu button while applying power and the output rate is set to 1024 x 768 at 60 Hz during the first power on cycle. Hold the Menu button while applying power a second time and the output rate will toggle to 720p at 60 Hz. Front Panel Controls ADJUST Use the Menu and Enter Buttons and two rotary encoders (shown in the MENU ENTER figure at right) to open and navigate the menu, which is displayed on the connected output display device. A typical on-screen menu is shown in the figure at right. Press the Menu button to display the top level menu. Use the rotary encoders to highlight menu items and the Enter button to select the highlighted item and move deeper into the menu. To move back one level, press the Menu button. For complete information about configuring and controlling the unit through the front panel controls and the on-screen display, see the RGB-DVI 300 and RGB-HDMI 300 (A) User Guide, which is available online at www.extron.com.