1. Manuals
  2. Brands
  3. XtendLan Manuals
  4. Security Camera
  5. Speed Dome
  6. User manual

XtendLan Speed Dome User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SPEED DOME
USER
MANUAL
Please read the manual carefully before operation

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Speed Dome and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for XtendLan Speed Dome

Summary of Contents for XtendLan Speed Dome

  • Page 1 SPEED DOME USER MANUAL Please read the manual carefully before operation...
  • Page 2 ◎ When connecting to the power source, please follow all electric safety standards and only use the power supply designated for this device. The speed dome’ s RS-485 and video signal uses TVS technology to protect it from strong electric surges. This technology prevents damage to the device resulting from impulse signals such as lightning strikes or surges under 500W power.

  • Page 3: Table Of Contents

    II)Technical Data ----------------------------------------- 5．5. Guard Location ------------------------------------------19 2．1. Speed Dome Technical Parameter -----------------------4 5.5.1 Setting the Guard Location --------------------------------20 2．2. Speed Dome Camera Technical Parameter -----------------5 5.5.2 Switches of Guard Location --------------------------------20 2．3. Lens Technical Parameter ----------------------------------5 5．6. Camera Control ----------------------------------------20 III)Dome Camera Installation and Setting 5.6.1 Zoom Control...

  • Page 4: I)Production Introduction

    1－60s Available an advanced technological surveillance product combining an all-direction variable Preset Positions speed dome and digital decoder all in one unit. It can aim quickly and scan Running to Preset Speed: 0.5º -280° continuously, making omni-directional and non-blind-spot monitoring into reality.
  • Page 5 III Dome Camera Installation and Setting Matri Code Address Setting: 3.1. Dome Camera Controlling ： Notice: To assure the normal signal communication, a 120 ohm R should be Note Matri code baud rate: 9600B connected to the farthest dome when one control bus control more than two domes.
  • Page 6 S w i t c h S e t t i n g S w i t c h S e t t i n g Receiving Receiving S w i t c h S e t t i n g S w i t c h S e t t i n g Address Receiving...
  • Page 7 PELCO- P Code Baud Rate Setting： Receiving S w i t c h S e t t i n g Receiving S w i t c h S e t t i n g Address Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 S wi t ch S e tti ng Sw itch Sett ing...

  • Page 8: Wall Mount Installation Connection

    IV. Wall Mount Installation Connection S w i t c h S e t t i n g S w i t c h S e t t i n g Receiving Receiving Address Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2- SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2- SW2-7 SW 2-8 Notice:...

  • Page 9: Wire Connection

    4.2 Dome Camera Ceiling Installation 4.2.1 Holing On the Ceiling a. Draw a circle on the ceiling according to the size of the speed dome b. Use drill to cut a circle on the ceiling a. Set the DIPswitches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address.

  • Page 10: Housing Installation

    Loose the screws on the out dome cover and open the cover. in the same direction clockwise in order to connect the dome with the ceiling b. Connect BNC video interface of speed dome camera with video wire (BNC). surface closely.

  • Page 11: 5．2. Setting And Calling Preset Position

    Input 03, then press SHIFT+PAN-A on the keyboard after three 5.3. Dome Pattern Tours seconds Pattern Touring is a key function of the speed dome camera. You can layout Input 32-grade, then press AUTO the preset position order to the pattern tours through our advanced program.

  • Page 12: Setting The Guard Location

    When in manual mode, operate the focus control to focus desired Press MPX or Auto until LCD displays: object automatically. Note: The Speed dome will not do auto focus on the target object under the 3.Press ENTER to following conditions: Setup Watch Position a.

  • Page 13: Auto White Balance

    3) FOCUS: AUTO（Auto Focus） 5.6.5 Auto White Balance Press down PAN_A key, status changes between AUTO (auto)/ MAN The speed dome will automatically adjust the white balance in accordance (Manual) with the changing background lighting conditions to achieve life mage.
  • Page 14 VII PELCO-D/PELCO-P Protocol Order Chart 15) LOST POWER SAVE（Save setup） Press down DVR key to save setup. Setup will be invalid without PELCO protocol has no relative order of some special functions. Thus, we pressing the key if the menu setup should be changed. make functional shifts between “...

Table of Contents