Table of Contents
Advertisement
Quick Links
Spesifications Avanti S
Type
: T.A.V.S Airex Carbon Composite
Length : 112" (2860mm)
Weight : 38—44Lbs ( 18—20 Kg)
Avanti S XXL
Thank you very much for purchasing our Avanti S XXL. Please note that the photos in this instruction manual
show certain views from the prototypes. Some modifications and upgrades might have taken place by the release of
the model. This manual describes the assembling of " PRO" model. Before you start building and setting-up your
aircraft, please make sure you have read this instruction manual, and understood it. If you have any questions,
please don't hesitate to contact us.
INSTRUCTIONS MANUAL
Span
Engine : 40—45 Lbs (18—21 Kg) trust
SEBART © 2014
: 97.6" (2480mm)
XXL
Advertisement
Table of Contents
Related Manuals for Sebart Avanti S XXL
Summary of Contents for Sebart Avanti S XXL
- Page 1 Avanti S XXL Thank you very much for purchasing our Avanti S XXL. Please note that the photos in this instruction manual show certain views from the prototypes. Some modifications and upgrades might have taken place by the release of the model.
-
Page 2: Table Of Contents
Assembly & Operation Manual Index: INTRODUCTION............................3 DISCLAIMER..............................3 WARNING…...............................3 ARF PAINT..............................4 FINISHING YOUR AVANTI ARF........................4 HANDLING & TRANSPORTING .......................5 TOOL LIST..............................6 HEALTH…..............................7 GENERAL ASSEMBLY TECHNIQUES....................…7 RADIO EQUIPMENT & ACCESSORIES…………….................8 KIT CONTENTS…….…………….......................9 OPTIONAL PARTS………………..………………..................10 CONTROL LINKAGES ..........................12 WINGS..............................12 STABILIZERS............................15 FIN & RUDDER............................16 FUSELAGE REAR &... -
Page 3: Introduction
INTRODUCTION Thank you for purchasing Sebart Avanti S. We have put a lot of effort and time into this model. We at Skymaster strive to be a market leader in the ARF— jet market. We were the first company to produce ARF—jets in the world and we would like to continue being amongst the best. -
Page 4: Arf Paint
Assembly & Operation Manual ARF Paint The color finish on your Avanti S arf pro model was applied out of the mould. We have used only the highest standard automotive paints to finish your model. Should you damage the finish, Skymaster stock the color paint and hardener required for the repair. -
Page 5: Handling & Transporting
Assembly & Operation Manual HANDLING & TRANSPORTING Composite models are very light but strong. These characteristics do have a down side! It is brittle. Take care when handling your model. DO NOT ATTEMPT TO PICK UP AN FULLY FUELED MODEL BY THE LEADING EDGE BY YOURSELF! The leading edges will crack and delami- nate. -
Page 6: Tool List
Assembly & Operation Manual Tools and Adhesives Tools etc: This is a fairly quick and easy plane to build, for a jet model, not requiring difficult techniques or special equip- ment, but even the building of Skymaster aircraft requires some suitable tools! You will probably have all these tools in your workshop anyway, but if not, they are available in all good hobby shops, or hardware stores like "Home Depot"... -
Page 7: Health
Assembly & Operation Manual HEALTH Use a mask (available at auto paint stores) to protect from inhaling the glass or carbon fiber dust. Use this mask whenever you are sanding or cutting fiberglass or carbon fiber materials. Use a charcoal filter paint mask (available at auto paint supply stores) when spraying any primer or paint. -
Page 8: Radio Equipment & Accessories
Assembly & Operation Manual Radio equipment Failure to use the recommended servos, output arms, extensions, and hardware may result in a loss of con- trol! Throughout this manual we make use of various types of servos and radio equipment! We have used JR equipment during the installation process. -
Page 9: Kit Contents
Kit Contents Assembly & Operation Manual Avanti S ARF PRO Contents: Right wing including L/G + Doors installed. Include flap + aileron Left wing including L/G + Doors installed. Include flap + aileron Avanti wing fence L + R Fuselage front including nose gear + door installed. Including door cylinders installed + Hatch Fuselage rear Fin + Rudder Stabilizer L + R incl elevators) -
Page 10: Optional Parts
Assembly & Operation Manual 3 x Air Tanks 1 x Retract Valve 2 x Filler & 2 x Pressure Gauges 1 x Electronic Brake Valve 5 x Air Tubing, 10 x Quick Disconnect 8 x T-pieces, 2 x 4 way Photo 1 Fuel Tank (1) 5,2L Smoke Tank (1) 2L... - Page 11 Assembly & Operation Manual Pushrod set Photo 7 Oleo oil and pressure kit Photo 8 Tank Hardware Photo 9 Hardware Photo 10 P-11...
-
Page 12: Control Linkages
Assembly & Operation Manual CONTROL LINKAGES Flaps 80 mm (2) Aileron : 100 mm (2) Elevator : 100 mm (2) Rudder : 115 mm (1) Steering: 55 mm Photo 11 WINGS NOTE: Make sure to have some sort of protective foam on the work bench. - Page 13 Assembly & Operation Manual Fit L-shape servo brackets to JR DS8911 Aileron servo must be mounted with horns facing outwards and must be furthest from control surface Secure servo horn and centre servo with TX. Photo 14 Secure extension wire. Use safety clips on joint. Fit servo to wing.
- Page 14 Assembly & Operation Manual Secure servo horn to flap servo and set travel with TX. Mark location of servo horn on wing skin. Cut slot. Fit servo to ply mount with horn facing down. Photo 19 Draw line perpendicular to hinge line and mark location of flap pushrod. Secure pushrod to servo horn.
-
Page 15: Stabilizers
Assembly & Operation Manual STABILIZERS NOTE: Make sure to have some sort of protective foam on the work bench. This will protect the paint surface from unwanted dents. Mark √ each step. Photo 21 Photo 22 Fit servo horns and adjust travel and sub-trim with TX. Mark location of servo horn exit on bottom skin of stab. -
Page 16: Fin & Rudder
Assembly & Operation Manual Make sure no slop and binding in system Run servo wires together in harness. NOTE : Make sure no wires can touch tailpipe. Touching tailpipe will melt wires and create short circuit. This will lead to crash. FIN &... -
Page 17: Fuselage Rear & Tailpipe
Assembly & Operation Manual FUSELAGE REAR + TAILPIPE Make sure you have a good stand for fuselage. You will need to assemble the rest of the Avanti on this stand. Fuselage have a removable tail for easy transport. Install extension wires for 3 servos in the tail. Make sure wires do not touch the tailpipe. -
Page 18: Front Fuselage
Assembly & Operation Manual FUSELAGE FRONT Fit the steering servo with m3 bolts. Make pushrod and secure. Check operation of steering. Photo 34 Fasten all screws on nose unit. Check operation of gear doors. Cut slots in engine mount to clear bel mouth. Photo 35 Trail fit rear of fuselage to front of fuselage. -
Page 19: Fuel Diagram
Assembly & Operation Manual FUEL CELL DIAGRAM Photo 40 P-19... -
Page 20: Air System
Assembly & Operation Manual AIR SYSTEM There are 2 options available for the air system: Mechanical or Electronic. For mechanical you will need 2 x 2 way and 1 x 1way valve with 3 servos and sequencer. For electronic you will need 1 x EV5U. Photo 41 The 1 large tank is for operation of gears and doors and the smaller tank for brakes. -
Page 21: Air Diagram
Assembly & Operation Manual You can also use separate valves to control the L/G you will require two 2 way elec- tronic valves and one 1 way valve. Photo 42 2 way AIR DIAGRAM Photo 43 Diagram for retracts P-21... -
Page 22: Turbine Installation
Assembly & Operation Manual TURBINE INSTALLATION Please follow the instructions supplied with your turbine. Secure turbine to turbine rail via rear of fuselage. . Run all turbine wires and power cables on opposite side of servo wires. Always secure all wires in harness. I would suggest you install a FOD. -
Page 23: Cockpit & Canopy
Assembly & Operation Manual COCKPIT AND CANOPY (after painting) Trace the shape of canopy and cut to fit. Glue with canopy glue. (only for white ordered model) Trial fit cockpit and cut to fit. Glue cockpit to canopy frame with silicon. Or secure with bolts. Fit pilot. -
Page 24: Equipment Installation
Assembly & Operation Manual EQUIPMENT INSTALLATION INTO Avanti S Equipment installation is a personal venture. There is one golden rule: Do it as neat and logical as possible! This will make fault finding and service of components eas- ier. The Jet basically consist of 6 circuits! 1. -
Page 25: Before You Fly
Assembly & Operation Manual BEFORE YOU FLY It is assumed that the builder of this kit has acquired the basic skills and knowledge necessary to make a safe and functional radio control installation into a model. Therefore, these notes are intended only to assist that experience. When inserting the main spar into wing, make sure it only enters the amount required. - Page 26 Nose high landings are easy with a very effective stab. Taxi back and do necessary adjustments to customize Avanti for your need! We at Skymaster and Sebart wish you many happy flights with your Avanti! Add some smoke and thrust vectoring and paint the sky!