Table of Contents
Advertisement
Quick Links
SebArt
The new KatanaS 30E ARF was designed by Italy aerobatic pilot,
Sebastiano Silvestri and the design is based on of his successful
and famous KatanaS Tournament Of Champion airplane.
This professional ARF kit is the results of a long Sebastiano's
research in 3D performance combined with an extremely
lightweight structure. The all wood airframe and the big control
surfaces give the KatanaS 30E an impressive thrust-to-weight
ratio and crisp control authority at any airspeed and flight
conditions....that for this small class of airplane is revolutionary!
The KatanaS 30E can do it all...unbelivable easy harriers, torque
rolls, blenders, waterfall and almost anything else you can dream
up are waiting you!
.....the only aerobatic limit is your fantasy!
Specifications
Wingspan:.............125 cm (49,21 in)
Lenght:................ 125 cm (49,21 in)
Wing Area:............36,5 dm² (56,57 sq.in)
KatanaS
ARF
ASSEMBLY MANUAL
professional line
30E
Weight:.....1.2 kg (2,.64 lb) with T.P. 2100 LiPo
Radio:......minimum 4-channel with 4 servos 12g
Engines:....Hacker A30-12L/14L+ X40 controller
Advertisement
Table of Contents
Related Manuals for Sebart Professional KatanaS 30E
Summary of Contents for Sebart Professional KatanaS 30E
- Page 1 SebArt professional line KatanaS ASSEMBLY MANUAL The new KatanaS 30E ARF was designed by Italy aerobatic pilot, Sebastiano Silvestri and the design is based on of his successful and famous KatanaS Tournament Of Champion airplane. This professional ARF kit is the results of a long Sebastiano’s research in 3D performance combined with an extremely lightweight structure.
-
Page 2: Table Of Contents
Table of contents Table of contents.......................……….. 2 Required radio and motor......................…. 3 Additional required items, tools and adhesives................3 Warning............................3 Before starting assembly ......................… 3 Using the manual........................... 3 Warranty information…......................... 4 Section 1 – wing fillet installation…....................5 Section 2 –... -
Page 3: Required Radio And Motor
Required radio and motor Radio equipment: • Minimum 4-channel radio system • 4 digital mini servos, recommended JR PROPO DS 381 • 2 servo extension 300mm, for elevator and rudder servos • 4 servo extension 100mm, for aileron’s servos Recommended electric motors for best performance: •... -
Page 4: Warranty Information
Rember to take your time and follow the directions. Warranty information SebArt garantees this kit to be free from defects in both material and workmanship at the date of purchase. This warrantiy does not cover any parts damage by use or modification, and in no case shall SebArt’s liability exceed the original cost of the purchased kit. -
Page 5: Section 1 - Wing Fillet Installation
Section 1 – wing fillet installation step 1 Locate the corresponding wing fillet to the wing. Test fit the fillet and his alignment with the wing panel. Once satisfied with the fit, glue the wing fillet to the wing panel using medium CA. Use carefully the glue and hold away and clean, from the zone of the contact, the covering material that will be used to cover the zone. -
Page 6: Section 2 - Ailerons Installation
Section 2 – ailerons installation step 1 Place in the aileron the four hinges, included in the hardware pack, in their place and verify the correct position and alignment of the aileron with the wing panel. step 2 Carefully glue, with some drops of thin CA, each of the four hinges in the aileron. -
Page 7: Section 3 - Aileron Servo & Control Horn Installation
step 3 Carefully glue, with some drops of thin CA, each of the four hinges into the wing panel. step 4 Work the aileron up and down some times to work the hinges and check for proper movement. step 5 Repeat steps 1 through 4 for the remaining wing panel. - Page 8 step 2 Locate the following items included in the hardware pack, one servo extension 100mm long and the servo. step 3 Install the servo hardware (gommets and eyelets) included with the servo. Install the servo and control horn into the wing panel as follow. step 4 Repeat steps 1 through 3 for the remaining wing panel.
-
Page 9: Section 4 - Rudder Installation
Section 4 – rudder installation step 1 With the hobby knife open the place for the servos and the stabiliser on both sides into the fuselage. Than place the rudder in his place into the fuselage, check for a correct alignment and than glue it with some drops of thin CA. -
Page 10: Section 5 - Elevator Installation
Section 5 – elevator installation step 1 Place in the elevator the four hinges, included in the hardware pack, in their place and verify the correct position and alignment of the elevator with the stabilizer. Than carefully glue the hinges, with some drops of thin CA, in the elevator only. step 2 Insert carefully the elevator before, and right after insert the stabiliser into fuselage space. - Page 11 step 4 Locate the carbon tube in his position and check the alignment with the stabilizer. step 5 Carefully place the hinges in their place, and glue the hinges with some drops of thin CA. step 6 Once satisfied with the alignment, glue with some drops of thin CA the stabilizer at the fuselage.
-
Page 12: Section 6 - Tail Wheel Installation
Section 6 – tail wheel installation step 1 Locate the items included in the hardware pack as follow. step 2 With the hobby knife cut a groove of 20mm length into the rudder. step 3 Install the tail wheel and apply some drops of thin CA, as follow. -
Page 13: Section 7 - Elevator / Rudder Servo & Control Horn Installation
Section 7 – elevator / rudder servo & control horn installation step 1 Locate the following items included in the hardware pack, servo extension 300mm long and the servo. Install the servo hardware (gommets and eyelets) included with the servo. step 2 Install the elevator servo and control horn into the fuselage as follow. -
Page 14: Section 8 - Landing Gear & Wheels Installation
Section 8 – landing gear & wheels installation step 1 Locate the landing gear on the fuselage and fix with the two screws included in the hardware pack. step 2 Locate all the necessary items for installing wheel and wheel pants. Than install all the items as follow and fix the wheel pant with some drops of thin CA at the landing gear. -
Page 15: Section 9 - Electric Motor Installation
Section 9 – electric motor installation We raccomand to fly HACKER engine, and you need one of this two options: • Hacker A30-12L + X40 controller + APC 13 x 6.5 E • Hacker A30-14L + X40 controller + APC 14 x 7 E step 1 Open the hole in the motor mounting plate to clear the C-clip on the motor, using a tapered reamer to remove enough material to allow the C-clip to clear the surrounding wood and rotate freely. -
Page 16: Section 10 - Cowl Installation
step 3 Cut and locate the two air plastic air scoops and glue them with thin CA as follow. step 4 Locate the engine and fix it with the four screws included in the engine hardware pack and right after locate the controller as follow. Section 10 –... - Page 17 step 2 Slide the cowling onto the fuselage and install the spinner back plate. Position and hold the cowl so there is 2mm gap between the back plate and the cowl. Than apply an other piece of masking tape on the same line of the one applied before. Drill the location for the four self-tapping screw using a 1.5mm drill bit.
-
Page 18: Section 11 - Final Radio Installation
Section 11 – final radio installation Section 12 – wings installation Control throws Please, follow carefully the recommended linkage setups for ailerons and elevators. For the AILERON we raccomand the following throws: Low rate: 20° up / 20° down Expo: 40% 3D rate: 45°... -
Page 19: Rates And Expos
K K D D Y Y H HD DQ Q L L F F H HI I O O L L J J K K W W SebArt di Sebastiano Silvestri Via Roma 83/85 38017 Mezzolombardo (TN) –...