Gold Medal ShaveMaster II 1005 Instruction Manual

Gold Medal ShaveMaster II 1005 Instruction Manual

Block ice shaver

Advertisement

ShaveMaster II
Part No. 12354
Revised June 1996
Block Ice Shaver
Instruction Manual
Model #1005
Cincinnati, OH 45241-4807 USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ShaveMaster II 1005 and is the answer not in the manual?

Questions and answers

Summary of Contents for Gold Medal ShaveMaster II 1005

  • Page 1 ShaveMaster II Part No. 12354 Revised June 1996 Block Ice Shaver Instruction Manual Model #1005 Cincinnati, OH 45241-4807 USA...
  • Page 2: Safety Precautions

    SAFETY PRECAUTIONS...
  • Page 3 ShaveMaster II HOW TO OPERATE THE SHAVEMASTER II MAIN SHAFT Rotates when motor is "ON". Keep fingers away. Step 2: HAND WHEEL Step 1: LOCKING KNOB for main shaft. Pull and turn to "unlock" Rotate to maintain main shaft. Be sure the height.
  • Page 4: Specifications

    ShaveMaster II SPECIFICATIONS Dimensions: 28" High x 11" Wide x 20" Deep Shipping Weight: 83 Lbs. Electrical Requirement: 120 Volts, 60 Hz, 4.7 Amps, 1 Phase Shaving Capacity: 4.4 – 5.5 Lbs./Min. RPM: 250 rpm Shaving Plate Diameter: 9 ¾" Ice Block Capacity: 6"...
  • Page 5: Cleaning Instructions

    ShaveMaster II ICE BLOCK FREEZING SUGGESTIONS 1. Use Gold Medal's plastic Ice Mold with Lid (Part No. 1085) to freeze blocks of ice. 2. Fill the container with cool tap water to a ½" from the top rim of the container.
  • Page 6: Maintenance Instructions

    OILING THE MAIN DRIVE SHAFT AND CRANK 1. The main shaft must be kept lubricated at all times with Gold Medal food approved Gear Lube (Part No. 1110). Do NOT use vegetable oil for lubrication; as the oil hardens, it will prevent the main shaft from rotating.
  • Page 7 ShaveMaster II ASSEMBLING THE BLADE COMPONENTS AFTER CLEANING OR, ADJUSTING BLADE IF MACHINE DOES NOT SHAVE. 1. Remove the (2) ¼-20 Thumb Screws from the underside of the Shaving Platter. 2. Remove the Shaving Platter from Support Casting and place it on a smooth flat surface preferably a table or counter top.
  • Page 8: Troubleshooting

    3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 or, place orders at:...
  • Page 9: Shavemaster Ii Assembly

    ShaveMaster II SHAVEMASTER II ASSEMBLY #1005 ODEL...
  • Page 10: Parts List - Shavemaster Ii Assembly

    ShaveMaster II PARTS LIST – SHAVEMASTER II ASSEMBLY Item No. Part No. Description 12115 Rocker Switch, SPST 12302 Bellow, Gear Protector 12305 Upper Mount Casting 12306 Gear Housing 12308 Brake Shoe 12309 Blade Platter 12310 Blade Holder 12399 Pivot Bracket, Blade 12312 Blade Mount 12313...
  • Page 11 ShaveMaster II PARTS LIST – SHAVEMASTER II ASSEMBLY ( continued ) Item No. Part No. Description 12353 Tube Spacer 12357 Worm Gear Assembly 12329 Worm Gear 12359 Gear Lock Assembly 12360 Switch, Door Safety 12361 Bracket, Safety Switch 12364 Knob, Brake Adjustment 12365 Hinge Mt, Plate Assembly 12368...
  • Page 12: Electrical Schematic

    ShaveMaster II ELECTRICAL SCHEMATIC #1005 ODEL...
  • Page 13: Warranty

    WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any...

Table of Contents