Gold Medal Sno-Pro 1800 Instruction Manual
  1. Manuals
  2. Brands
  3. Gold Medal Manuals
  4. Ice Maker
  5. Sno-Pro 1800
  6. Instruction manual
Gold Medal Sno-Pro 1800 Instruction Manual

Gold Medal Sno-Pro 1800 Instruction Manual

Ice shaver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Part No. 22132
MARCH 2008
Sno-Pro
Instruction Manual
Model #1800
Cincinnati, OH 445241-4807 USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sno-Pro 1800 and is the answer not in the manual?

Questions and answers

Related Manuals for Gold Medal Sno-Pro 1800

Summary of Contents for Gold Medal Sno-Pro 1800

  • Page 1 Part No. 22132 MARCH 2008 Sno-Pro Instruction Manual Model #1800 Cincinnati, OH 445241-4807 USA...

  • Page 2: Safety Precautions

    Sno-Pro Safety Precautions All Models #1800...

  • Page 3: Installation

    ICE REQUIREMENTS The Sno-Pro can take ice cube (small or medium in size) or small block ices, if you break the block into pieces approximately 2 to 3 inches in size. NOTE: The ice will not enter the shaving chute if the pieces are too large.

  • Page 4: Maintenance Instructions

    Sno-Pro MAINTENANCE INSTRUCTIONS All Models #1800...

  • Page 5: Ordering Spare Parts

    3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 or, place orders at: (513) 769-7676 Fax: (513) 769-8500 E-mail: goldme19@eos.net All Models #1800...
  • Page 6 Remove the 5 screws holding the top cover on the unit. Slide the cover out of the way as shown below COVER SCREWS QUICK CONNECTOR 3. Un – couple the quick connect on the electrical lead going to the magnetic switch. All Models #1800...
  • Page 7 6. The Shaver band blade has 6 tabs on the exterior of the hopper. Twist the tabs to align with the slots in the hopper. Once all 6 are aligned with the slot openings. Push the tabs thru the slots removing the blade. TABS All Models #1800...
  • Page 8 Note: The impeller might need to be rotated to allow for easily assembly. 10. Re-Install the 4 thumb screws. 11. Reconnect the electrical quick connect. 12. Reinstall the 5 screws in the top cover. All Models #1800...
  • Page 9 Sno-Pro MODEL 1800 ASSEMBLY All Models #1800...
  • Page 10 Sno-Pro MODEL 1800 ASSEMBLY All Models #1800...
  • Page 11 Sno-Pro MODEL 1800 ASSEMBLY All Models #1800...
  • Page 12 Sno-Pro BAND BLADE AND HOPPER ASSEMBLY All Models #1800...

  • Page 13: Parts List

    12728 Band Blade 12652 Hinge Pin 12736 Magnet Mount Block 12078 Magnet 12116 Micro Switch 12668 Drain Fitting 12687 Push In Fastener 22034 Hose - clear 12793 Knob 22132 Manual 27563 Wrench (used in removal of impeller) All Models #1800...
  • Page 14 Sno-Pro ELECTRICAL SCHEMATIC MODEL #1800 All Models #1800...

  • Page 15: Warranty

    543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY 10700 Medallion Drive Cincinnati, Ohio 45241-4807 USA All Models #1800...

Table of Contents