Kenwood VR-509 Instruction Manual page 21

3
Adjust the speaker volume.
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
1 Use the MULTI CONTROL knob or 5/∞ keys to adjust the
volume of the test tone output from the speaker channel to be
adjusted.
The channel indication blinks while the test tone is being output.
SP A B TI.VOL
L C R
CLIP MUTE
LFE
RDS EON PTY
LS S RS
TP TA NEWS
The test tone is heard from the speakers in the following
sequence for 2 seconds each:
= L = C = R = SR = SL = SW
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed
• If the speaker setting selects are OFF, the speaker level settings
are reset.
2 Press the SET UP or display operation 2 [Next] key.
• The test tone is turned off. The receiver enters the mode for inputting
the distance to the speakers.
4
Input the distance to the speakers.
1 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
Distance to center speaker:
Distance to surround speakers:
2 Use the MULTI CONTROL knob or 5/∞ keys to select the
distance to the front speakers.
The speaker indicator to be adjusted blinks.
SP A B TI.VOL
L R
C
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP or display operation 2 [Next] key.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
5 Setup is complete when the input indication reappears.
SP A B TI.VOL
L
CLIP MUTE
LFE
RDS EON PTY
LS
TP TA NEWS
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
____ feet (meters)
____ feet (meters)
____ feet (meters)
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX
Indication in meters
C R
SW
S RS
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink. Adjust the input level.
CLIP
RDS
TP
1 Use the INPUT SELECTOR knob to select the source which
AUTO
MEMO
input level you want to adjust.
ST.
TUNED
• You can store a separate input level for each input source. If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key repeatedly until the "INPUT"
indication appears.
º
3 Use the MULTI CONTROL knob or 5/∞ keys to adjust the
input level.
SP A B
CLIP
RDS EON
TP TA
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
AUTO
MEMO
ST.
DSP TUNED
Preparing for surround sound
TI.VOL
L C R
MUTE
LFE SW SW
PTY
LS S RS
NEWS
21
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
ST.
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP TUNED