Preparing For Surround Sound; Speaker Settings - Kenwood VR-509 Instruction Manual

Preparing for surround sound

Speaker settings

20
To enable you to obtain optimum enjoyment from the receiver's listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
MULTI CONTROL
POWER (
Display operation 1
Display operation 2
1
Turn on the power to this receiver by pressing POWER
( ) or SYS. POWER (
2
Select a speaker system.
1 Press the SET UP key such that the subwoofer setting
indication (SUBW ON) appears.
SP A B TI.VOL
L C R
CLIP MUTE
LFE SW
RDS EON PTY
LS S RS
TP TA NEWS
When you operate on the remote control unit
1 1 1 1 1 Press the display operation 2 [Menu] key repeatedly until
"01.IR" appears in the display of the remote control unit.
>01.IR
>02.Surround
Home Enter
2 2 2 2 2 Press the 5/∞ keys to select "02.Surround", then press
the display operation 2 [Enter] key.
SetUp
Home Next
2 Use the MULTI CONTROL knob or 5/∞ keys to select the
appropriate subwoofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver is
2 SUBW OFF : Subwoofer setting mode to the receiver is
• The initial setting is "SUBW ON".
• When "SUBW OFF" is selected, the front speakers are automatically
set to "FRNT LRG" and the procedure skips to step 5.
• When subwoofer output sound is required, selected "FRNT NML".
SET UP
)
5/∞
SYS. POWER (
+ +
— —
) key.
FM AUTO SOUND
AM PRO LOGIC
MHz 3 STEREO
kHz DOWN MIX
ON.
OFF.
3 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The front speakers setting indication (FRNT) appears.
SP A B TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
4 Use the MULTI CONTROL knob or 5/∞ keys to select the
appropriate front speakers setting.
1 FRNT NML (normal) : Average size front speakers are
2 FRNT LRG (large)
• For "FRNT LRG" selection, no sound will be heard from SUBW
even when it is set to ON. However, if you select CINEMA EQ.
when subwoofer is selected, you will be able to hear sound from
the subwoofer.
When in STEREO mode, the sound goes directly to front speaker.
5 Press the SET UP or display operation 2 [Next] key to accept
the setting.
) • The center speaker setting indication (CNTR) appears.
6 Use the MULTI CONTROL knob or 5/∞ keys to select the
appropriate center speaker setting.
If you selected "LRG" as the front speakers setting,
1 CNTR LRG (large)
2 CNTR NML (normal) : An average size center speaker is
3 CNTR OFF
If you have selected "NML" as the front speakers setting,
1 CNTR ON : Center speaker setting mode to the receiver
2 CNTR OFF : Center speaker setting mode to the receiver
DIGITAL AUTO
S.DIRECT MEMO
MONITOR ST.
TUNED
DSP
7 Press the SET UP or display operation 2 [Next] key to accept
the setting.
• The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL knob or 5/∞ keys to select the
appropriate surround speaker setting,
If you have selected "LRG" as the center speaker setting,
1 SURR LRG (large)
2 SURR NML (normal) : Average size surround speakers are
3 SURR OFF
If you have selected other than "LRG" as the center speaker
setting,
1 SURR ON : Surround speaker setting mode to the receiver
2 SURR OFF : Surround speaker setting mode to the receiver
9 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected
channels of the speakers that require adjusting.
L C R
LFE SW
LS S RS
connected to the receiver.
: Large front speakers are connected
to the receiver.
: A large center speaker is connected
to the receiver.
connected to the receiver.
: Center speaker setting mode to the
receiver is OFF.
is ON.
is OFF.
: Large surround speakers are
connected to the receiver.
connected to the receiver.
: Surround speaker setting mode to
the receiver is OFF.
is ON.
is OFF.
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX DSP