Download  Print this page

Recording; Recording Audio (Analog Sources); Recording Video; Recording Audio (Digital Sources) - Kenwood VR-509 Instruction Manual

Audio video surround receiver
Hide thumbs

Advertisement

Recording

Recording audio (analog sources)

24
Recording a music source
1 Use the INPUT SELECTOR knob to select the source (other than
"MD/TAPE") you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
Recording tapes or MD (with MONITOR function)
MONITOR = MD/TAPE recording
1 Press the MONITOR key.
2 Use the INPUT SELECTOR knob to select a source other than
"MD/TAPE".
3 Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck or MD recorder
connected to the MD/TAPE jacks.
MD/TAPE = MONITOR recording
1 Use the INPUT SELECTOR knob to select "MD/TAPE".
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
MONITOR jacks.
• To copy tapes using a double cassette deck, refer to the instruction
manual of the double cassette deck.
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the MONITOR
jacks of the receiver. If a graphic equalizer is connected, the MONITOR
key should be left in the on position. Alternately, if a cassette deck
equipped with a 3-head system is connected to the MONITOR jacks,
you will be able to monitor the just-recorded signal while making
recordings on the cassette deck. By switching the MONITOR key on
and off, you can compare the sound of the source signal and the just-
recorded signal. For more information, refer to the instruction manual of
the connected component.
MONITOR
INPUT SELECTOR
FM
AUTO SOUND
DIGITAL
AUTO
AM
PRO LOGIC
S.DIRECT
MEMO
MHz
3
STEREO MONITOR
TUNED
kHz
DOWN MIX
DSP

Recording video

1 Use the INPUT SELECTOR to select the video source (other
than "VIDEO1") you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due to
the copy guard condition.

Recording audio (digital sources)

Switch on the REC mode to record a digital input source.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A- REC
mode, the audio may be interrupted momentarily.
Recording music in A-REC or M-REC mode
ST.
1 Use the INPUT SELECTOR knob to select the source (CD/DVD,
DVD/6ch, VIDEO2, or VIDEO3) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Press and hold the DIMMER key for more than 2 seconds to
select the A-REC or M-REC mode.
• The mode changes every 2 seconds as shown below.
1 Rec mode off :
2 A-REC :
3 M-REC :
For A-REC mode:
For M-REC mode:
4 Play the source from the beginning and start recording.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
DIMMER
INPUT SELECTOR
The digital input record mode is
switched off.
The digital input signals (DTS,
Dolby Digital, or PCM) are identi-
fied automatically and converted
into stereo signals that are ready
for recording.
The input signal type at the mo-
ment this mode is selected is held
throughout this mode.
FM
AUTO SOUND
AM
PRO LOGIC
MHz
3
STEREO
kHz
DOWN MIX
FM
AUTO SOUND
AM
PRO LOGIC
MHz
3
STEREO
kHz
DOWN MIX
FM
AUTO SOUND
AM
PRO LOGIC
MHz
3
STEREO
kHz
DOWN MIX
FM
AUTO SOUND
AM
PRO LOGIC
MHz
3
STEREO
kHz
DOWN MIX
DIGITAL
AUTO
S.DIRECT
MEMO
MONITOR
ST.
DSP
TUNED
DIGITAL
AUTO
S.DIRECT
MEMO
MONITOR
ST.
DSP
TUNED
DIGITAL
AUTO
S.DIRECT
MEMO
MONITOR
ST.
DSP
TUNED
DIGITAL
AUTO
S.DIRECT
MEMO
MONITOR
ST.
DSP
TUNED

Advertisement

Table of Contents
loading

  Also See for Kenwood VR-509

  Related Manuals for Kenwood VR-509