Download  Print this page

Adjusting The Sound - Kenwood VR-509 Instruction Manual

Audio video surround receiver
Hide thumbs

Advertisement

Adjusting the sound

MULTI CONTROL
SOUND
SPEAKERS A/B
PHONES
+
MUTE
SOUND
F.SHIFT
Adjusting the tone
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo mode.
1 Press the SOUND key repeatedly to select the tone mode to be
adjusted.
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
SP
A
B
TI.VOL
L
C
R
CLIP
MUTE
LFE
SW
RDS EON
PTY
LS
S
RS
TP
TA
NEWS
2 Use the MULTI CONTROL knob or 5/∞ keys to adjust the sound
quality.
• The bass and treble levels are adjustable from -10dB to +10dB in 2
step increments.
• The adjustment item is displayed for approximately 8 seconds.
Once-touch low frequency emphasis (bass boost) (Remote
control only)
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo modes.
Press the F.SHIFT key, then press BASS BOOST key on the
remote control.
• Press the key once to select the maximum (+10dB) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality or
ambience effects adjustment mode.
Switching back to the previous setting
Press the BASS BOOST key again.
SOURCE DIRECT
VOLUME CONTROL
5/∞
VOL.
+
BASS BOOST
FM
AUTO SOUND
DIGITAL
AM
PRO LOGIC
S.DIRECT
MHz
3
STEREO
MONITOR
kHz
DOWN MIX
DSP
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
SP
A
CLIP
RDS EON
TP
TA
To cancel
Press the MUTE key again so that the "MUTE" indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
SOURCE DIRECT playback (for analog sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
Press the SOURCE DIRECT key.
FM
AUTO SOUND
AM
PRO LOGIC
MHz
3
STEREO
kHz
DOWN MIX
• When you press the LISTEN MODE, SOUND, or SET UP keys, or
switch to another input source, SOURCE DIRECT playback will be
canceled.
• If CINEMA EQ. is switched ON, SOURCE DIRECT key will not be
effective.
• If SOURCE DIRECT is switched ON, CINEMA EQ. function will not be
effective.
To cancel
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated when using a surround
AUTO
MEMO
ST.
mode, canceling SOURCE DIRECT playback will reactivate the
TUNED
previous surround mode.
Listening with headphones
1 Press the SPEAKERS A and B key so that the speaker indicator
goes off.
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo play-
back.
2 Connect the headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob (VOL. +/– keys) to adjust the
volume.
B
TI.VOL
L
C
R
MUTE
LFE
SW
PTY
LS
S
RS
NEWS
Blinks
DIGITAL
AUTO
S.DIRECT
MEMO
ST.
MONITOR
TUNED
DSP
Make sure the SPEAKERS
indicators are turned off.
SP
A
B
TI.VOL
L
C
R
CLIP
MUTE
LFE
RDS EON
PTY
LS
S
RS
TP
TA
NEWS
Normal playback
23

Advertisement

Table of Contents
loading

  Also See for Kenwood VR-509

  Related Manuals for Kenwood VR-509