Recording; Recording Audio; Recording Video - Kenwood KRF-V5010 Instruction Manual

16
Muting the sound
MUTE lets you mute the sound of the speakers.
Press the MUTE key.
SP A
MUTE
Blinks
• On the KRF-V5010, this selection can be made using the control on
the receiver as well.
To cancel
Press the MUTE key again so that the "MUTE" indicator goes off.
• Muting can also be cancelled by adjusting the volume.
SOURCE DIRECT playback (analog sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
Press the SOURCE DIRECT key.
AUTO SOUND
S.DIRECT
• Either press the LISTEN MODE, SOUND, and SETUP keys, or
switch to another input source to cancel SOURCE DIRECT play-
back.
To cancel
Press again.
• If SOURCE DIRECT playback was activated when using a sur-
round mode, cancelling it reactivates the previous surround mode.
Listening with headphones
1 Use the SPEAKERS A or B key (or the SPEAKERS key) to turn
off the speaker indicator.
Make sure the SPEAKERS
indicators are turned off.
SP A
Models other than KRF-V5010
• If you turn off all of the speakers when in the surround mode, the
mode is cancelled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob (VOLUME) to adjust the vol-
ume.
To adjust the balance
Use the test tone feature.
Normal playback
C D
AUTO
MEMO.
ST.
TUNED
Make sure the SPEAKERS
indicators are turned off.
C
A
KRF-V5010
$ - 3

Recording

Recording audio

VIDEO 2 / MONITOR
Recording a music source
When recording a music source, switch the VIDEO2/MONITOR
setting to "MONITOR".
1 Use the input selector to select the source (other than "TAPE")
you want to record.
2 Set the cassette deck to record.
3 Start playback, then start recording.
Copying tapes
When copying tapes, switch the VIDEO2/MONITOR setting to
"MONITOR".
MONITOR = TAPE copying
1 Press the VIDEO 2/MONITOR
key.
2 Use the input selector to select a source other than "TAPE".
3 Start playback on the cassette deck connected to the VIDEO2/
MONITOR jacks and start recording on the cassette deck con-
nected to the MD/TAPE jacks.
TAPE = MONITOR copying
1 Use the input selector to select "TAPE".
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
VIDEO2/MONITOR jacks.
• To copy tapes using a double cassette deck, refer to the instruc-
tion manual of the double cassette deck.
C
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the VIDEO2/
MONITOR jacks of the receiver. If a graphic equalizer is connected,
the VIDEO2/MONITOR key should be left in the on position. Alter-
nately, if a cassette deck equipped with a 3-head system is con-
nected to the VIDEO2/MONITOR jacks, you will be able to monitor the
just-recorded signal while making recordings on the cassette deck.
By switching the VIDEO2/MONITOR key on and off, you can com-
pare the sound of the source signal and the just-recorded signal. For
more information, refer to the instruction manual of the connected
component.
To adjust the input level when the monitor function is turned on, use
the SOUND key and the MULTI CONTROL key.

Recording video

When recording video, switch the VIDEO2/MONITOR setting to
"VIDEO2".
1 Use the input selector to select the video source (other than
"VIDEO2") you want to record.
2 Set the video deck connected to VIDEO2/MONITOR to record.
3 Start playback, then start recording.
KRF-V7010/V6010/V5010 (En/T)
INPUT SELECTOR
8
8
AUTO SOUND AUTO
MEMO.
STEREO MONITOR ST.
TUNED
¢
8