Normal Playback; Preparing For Playback; Remote Operation Of Other Components - Kenwood KRF-V5010 Instruction Manual

14
3
Adjust the volume levels for the speakers.
Sit in your normal listening position and listen to the test tone. Adjust the
volume levels for the speakers until all speakers seem to be equally
loud.
1 Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume
when the test tone is being output from the speaker channel to
be adjusted.
The channel indication blinks while the test tone is being output.
SP A
L ch + dB
The test tone issues from the speakers for 1.5 seconds at a time
in the following sequence:
Lch = Cch = Rch = Sch = Lch
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
• If the speaker setting selects are changed, the speaker level
settings are reset.
2 Press the SETUP key.
• The receiver enters the mode for inputting the distance to the
speakers.
4
Input the distance to the speakers.
1 Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
Distance to surround speakers:
2 Use the MULTI CONTROL (TUNING/SKIP) to select the distance
to the front speakers.
The speaker indicator to be adjusted blinks.
SP A
1 )FT
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SETUP key.
4 Repeat steps 2 and 3 to input the distance for the surround
speaker.
5 Setup is complete when the input indication reappears.
C D
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all
the speakers have been correctly selected.
• If you used the remote control (RC-R0507) to perform the settings,
press the VIDEO key at this point to turn off the remote control's
own adjustment mode. In this case, the input source is not
switched.
Preparing for surround sound
1
¢
____ feets (meters)
____ feets (meters)
3 . )M
Indication in meters

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
VIDEO 2/MONITOR
ON/STANDBY
POWER
SPEAKERS A/B
SPEAKERS (KRF-V5010)
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER and ON/
STANDBY keys.
Selecting TAPE/MD
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting is "TAPE". To change
the source name associated with the MD/TAPE jacks to "MD," follow
the steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO key for more than two seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control
(RC-0507) to "MD".
Selecting the speaker system
Press the SPEAKERS A or B key to select the speaker system to
be used.
A ON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
B ON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
A+B ON : Sound from both the speakers connected to the SPEAK-
ERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listen-
ing with headphones for stereo sound in all playback
modes.
• Activating a surround mode or selecting "DVD 6ch" as the input
source causes speaker system A to be selected automatically.
On the KRF-V5010, press the SPEAKERS key to switch the speak-
ers on and off.
The indicator for the speakers
you want to use should be lit.
B
SP A
Models other than KRF-V5010
Selecting VIDEO 2/MONITOR
Depending on the component connected to the VIDEO 2/MONITOR
jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as
appropriate.
KRF-V7010/V6010/V5010 (En/T)
AUTO
INPUT SELECTOR
RC3
Speaker indicator lights.
SP
KRF-V5010
8