Listening To A Source Component; Adjusting The Sound - Kenwood KRF-V5010 Instruction Manual

Listening to a source component

INPUT SELECTOR
AUDIO
VIDEO
VOLUME
RC-R0507
1
Use the input selector (INPUT SELECTOR (AUDIO, VIDEO))
to select the source you want to listen to.
The input sources change as shown below:
Selecting a source using the INPUT SELECTOR knob
1 TUNER
2 "CD" ("CD"*)
3 "TAPE" or "MD" ("TAPE"*)
4 "PHONO"("PHONO"*)
5 "VIDEO1" ("VCR1"*)
6 "VIDEO2" ("VCR2"*)
7 "DVD 6ch"
Selecting a source using the AUDIO key
on the remote control (RC-R0507)
1 "CD" ("CD"*)
2 "TAPE" or "MD" ("TAPE"*)
3 TUNER
4 "PHONO"("PHONO"*)
Selecting a source using the VIDEO key
on the remote control (RC-R0507)
1 "VIDEO1" ("VCR1"*)
2 "VIDEO2" ("VCR2"*)
3 "DVD 6ch"
4 "<--->" (Not used by this receiver.)
• When selecting an input source by using the remote control (RC-
R0307), press the desired input selector key.
• "VIDEO 2" can be selected as an input source only if the VIDEO
2/MONITOR setting is "VIDEO 2".
* Once setup codes are registered in the remote control (RC-
R0507), the input name display changes according to the name of
the registered component.
Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears
instead of "VIDEO 1".
• When using the remote control (RC-R0507) after initial setup, any
inputs that have not been registered with a setup code are deleted
from the cyclic list.
• The INPUT SELECTOR on the front panel of the receiver always
cycles through all inputs.
2
Start playback from the selected source.
3
Use the VOLUME CONTROL (VOLUME) to adjust the
volume.
VOLUME CONTROL
VOLUME
RC-R0307
8
RC2
RC4

Adjusting the sound

SOURCE DIRECT
BASS BOOST SOUND
PHONES
SPEAKERS A/B
SPEAKERS, MUTE (KRF-V5010)
VIDEO
VOLUME
TUNING/SKIP
MUTE
SOUND
RC-R0507
Adjusting the tone
The following adjustments are possible if the receiver is in the stereo
mode.
1 Press the SOUND key to select the tone mode to be adjusted.
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
A
SP
T REB
2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound
quality.
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
• The adjustment item is displayed for approximately eight sec-
onds.
• If you used the remote control (RC-R0507) to perform the above
setting, press the VIDEO key at this point to turn off the remote
control's own adjustment mode. In this case, the input source is
not switched.
Once-touch low frequency emphasis (bass boost)
The following adjustments are possible if the receiver is in the stereo
mode.
Press the BASS BOOST key.
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality
or ambience effects mode.
Switching back to the previous setting
Press the BASS BOOST key again.
Normal playback
KRF-V7010/V6010/V5010 (En/T)
VOLUME CONTROL
MULTI CONTROL
BASS BOOST
MUTE
VOLUME
SOUND
MULTI CONTROL
RC-R0307
AUTO
+4
MEMO.
STEREO
ST.
TUNED
15