Recording Video; Recording Audio (Digital Sources); Listening To Radio Broadcasts; Tuning Radio Stations - Kenwood 5.1 KRF-V7050D Instruction Manual

Recording video

1 Use the INPUT SELECTOR to select the video source (other than
"VIDEO1") you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due to
the copy guard condition.

Recording audio (digital sources)

Switch on the REC mode to record a digital input source.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A-REC
mode, the audio input source may be interrupted momentarily.
Recording music in A-REC or M-REC mode
DIMMER
1 Use the INPUT SELECTOR knob to select the source (CD/
DVD, DVD/6ch, VIDEO2 or VIDEO3) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Press and hold the DIMMER key for more than 2 seconds to
select the A-REC or M-REC mode.
• The mode changes every 2 seconds as shown below.
1 Rec mode off :
2 A-REC :
3 M-REC :
For A-REC mode:
For M-REC mode:
4 Start playback, then start recording.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
Recording
t
INPUT SELECTOR
The digital input record mode is
switched off.
The digital input signals (DTS,
Dolby Digital, or PCM) are identified
automatically and converted into
stereo signals that are ready for
recording.
The input signal type at the moment
this mode is selected is held
throughout this mode.
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
FM AUTO SOUND DIGITAL
AM PRO LOGIC PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP
FM FM AUTO SOUND DIGITAL
AM AM PRO LOGIC PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR
kHz DOWN MIX DSP

Listening to radio broadcasts

The receiver can store up to 40 stations in the memory and recall them by
one-touch operation.

Tuning radio stations

MULTI CONTROL
RC-R0720
1
Use the INPUT SELECTOR knob or TUNER key to select the
tuner.
2
Use the BAND key to select the desired broadcast band.
Each press switches the band
as follows:
1 FM
2 AM
3
Use the AUTO/CINEMA EQ. key to select the desired
tuning method.
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
AUTO
MEMO
ST.
TUNED
• Normally, set to "AUTO" (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
AUTO
MEMO
ST.
TUNED
4
Use the MULTI CONTROL knob or keys to select the
station.
AUTO
MEMO
ST.
TUNED
AUTO
MEMO
ST.
TUNED
Auto tuning
Manual tuning :
INPUT SELECTOR
BAND AUTO/CINEMA EQ
MULTI
CONTROL
BAND
AUTO
TUNER
RC-R0613
"AM" or "FM" indicator
appears in the display
FM
AM
MHz
kHz
"AUTO" indicator lights up
in the display.
FM
AM
MHz
kHz
Frequency "ST." lights when a broadcast
display is being received in stereo.
FM
AM
MHz
kHz
"TUNED" is displayed when a
station is received.
: The next station is tuned automatically.
Turn the knob (press the key) to select the
desired station.
23
AUTO SOUND DIGITAL AUTO
PRO LOGIC S.DIRECT MEMO
ST.
3 STEREO MONITOR
DOWN MIX DSP TUNED
AUTO SOUND DIGITAL AUTO
PRO LOGIC S.DIRECT MEMO
3 STEREO MONITOR ST.
TUNED
DOWN MIX DSP
AUTO SOUND DIGITAL AUTO
PRO LOGIC S.DIRECT MEMO
3 STEREO MONITOR ST.
TUNED
DOWN MIX DSP