Messages - Panasonic SC-XH70 Operating Instructions Manual

USB
The USB drive or its contents cannot be read.
≥The USB drive format or its contents is/are not
compatible with the system. (
≥The USB host function of this product may not work
with some USB devices.
≥USB devices with storage capacity of more than 32 GB
may not work in some instances.
Slow operation of the USB device.
Large file size or high memory USB device takes longer
time to read and display on the TV.
HDMI progressive video
There is ghosting when HDMI progressive output is
on.
This problem is caused by the editing method or material
used on DVD-Video, but should be corrected if you use
interlaced output. When using the HDMI AV OUT
terminal, set "Video Resolution" in Video menu to "480i/
576i". Or, disable the HDMI connection and use the other
video connection. (
Radio
Distorted sound or noise is heard.
Adjust the position of the FM antenna.
A beat sound is heard.
Try to keep a certain amount of distance between the
antenna and the TV.
If noise is excessive.
Change the audio to be output as monaural.
Press and hold [PLAY MODE]9 to select "MONO".
The sound becomes monaural.
≥To cancel the mode, press and hold the button again
until "AUTO ST" is displayed. (The mode is also
cancelled when you change the frequency.)
In normal circumstances, select "AUTO ST".

Messages

The following messages or service numbers may appear
on the TV or unit's display.
TV displays
"/"
The operation is prohibited by the unit or disc.
"/ Incorrect Disc Region"
Only DVD-Video discs that include or have the same
region number as the one on the rear panel of this unit
can be played. ( Cover page)
Unit displays
"NO PLAY"
≥You inserted a disc the unit cannot play; insert one it
can. ( 22)
≥You inserted a blank disc.
≥You inserted a disc that has not been finalised.
"NO DISC"
≥You have not inserted a disc; insert one.
≥You have not inserted the disc correctly; insert it
correctly. ( 13)
26
18)
8, 19)
"USB OVER CURRENT ERROR"
The USB device is drawing too much power. Switch to
"DVD/CD" mode, remove the USB and turn the unit off.
"F61"
Check and correct the speaker cable connections. If this
does not fix the problem, consult the dealer. (
"F76"
There is a power supply problem. Consult the dealer.
"DVD U11"
Disc may be dirty. Wipe it clean.
"SET OK"
"SET OK" is displayed when the stations are set, and the
radio tunes to the last preset station.
"ERROR"
≥Incorrect operation performed. Read the instructions
and try again.
≥"ERROR" is displayed when automatic presetting is
unsuccessful. Preset the stations manually.
"TUNED/STEREO"
Displayed when receiving stereo broadcasting.
"TUNED"
Displayed when receiving monaural broadcasting or
monaural sound is selected.
"DVD H∑∑"
"DVD F∑∑∑"
∑ stands for a number.
≥Trouble may have occurred. The numbers following "H"
and "F" depend on the status of the unit. Turn the unit
off and then back on. Alternatively, turn the unit off,
disconnect the AC mains lead, and then reconnect it.
≥If the service numbers fail to clear, note the service
number and contact a qualified service person.
"U70∑"
∑ stands for a number. (The actual number following
"U70" will depend on the state of this unit.)
≥The HDMI connection acts unusually.
–The connected equipment is not HDMI-compatible.
–Use the High Speed HDMI Cables.
–The HDMI cable is too long.
–The HDMI cable is damaged.
"REMOTE 1" or "REMOTE 2"
Match the modes on this unit and remote control.
Depending on the number being displayed ("1" or "2"),
press and hold [OK]8 and the corresponding numbered
button ([1] or [2]) for at least 2 seconds. (
7)
4)