Kenwood VRS-N8100 Instruction Manual page 21

Preparing for playback
4
Select the setup method.
1 Select "Speaker Setup" and press the ENTER key (or
the Enter key) to select the speaker setup method.
2 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
for the following displays.
HTB 1 HTB 2
6.1ch 5.1ch 6.1ch 5.1ch 6.1ch
C
L SW
LS
BS
R E
S P
1 "HTB1 6.1CH": Select "HTB1 6.1CH" if you use speaker
system KS-3100EX. *
2 "HTB1 5.1CH": Select "HTB1 5.1CH" if you use speaker
system KS-2100HT. *
3 "HTB2 6.1CH": Select "HTB2 6.1CH" if you use speaker
system KS-708HT+KS-308EX or KS-308HT+KS-308EX. *
4 "HTB2 5.1CH": Select "HTB2 5.1CH" if you use speaker
system KS-708HT or KS-308HT. *
5 "HTB3 6.1CH": Select "HTB3 6.1CH" if you use speaker
system KS-908EX. *
6 "HTB3 5.1CH": Select "HTB3 5.1CH" if you use speaker
system KS-908HT.*
7 "Custom": Select to set up the speakers according to the
speaker system in use. (Speaker setup is required every
time after the speaker system is changed.)
8 "Exit": Select "Exit" and press the ENTER (or the Enter key)
to return to the previous display.
* Model availability may differ depending on the country
and sales area.
÷ When the 5.1 channel speaker system configuration is
used or the speaker setting is set to "BS/SW Amp Off",
the PL IIx, DTS-ES and DOLBY EX listen modes cannot
be selected.
If you selected "HTB1 6.1CH", "HTB1 5.1CH", "HTB2 6.1CH",
"HTB2 5.1CH", "HTB3 6.1CH" or "HTB3 5.1CH" in the above:
Press the ENTER (or the Enter key), then press the MULTI
CONTROL % / fi (or the Multi % / fi keys) to select "Yes", and
press the ENTER (or the Enter key) again to establish the setup.
÷ Select "No" to return to the status before setup.
÷ When you use a KENWOOD speaker system and select
"HTB1 6.1CH", "HTB1 5.1CH", "HTB2 6.1CH", "HTB2
5.1CH", "HTB3 6.1CH" or "HTB3 5.1CH" set the speaker
setup, the audio will be corrected automatically accord-
ing to the speaker characteristics.
Speaker Setup
Speaker Setup
HTB 3
Custom Exit
5.1ch
R
RS
C E I V E R S E T U P
E A K E R S E T U P
H T B 1 6 . 1 c h
If you selected "Custom" in the above:
Press the ENTER (or the Enter key) to proceed to detailed setups.
After this, continue the procedure from step 5.
The flow of the SETUP is as follows;
SPEAKER SETUP SPEAKER LEVEL
HTB 1 6.1CH
Test Tone Auto
HTB 1 5.1CH
HTB 2 6.1CH
Left
HTB 2 5.1CH
Center
HTB 3 6.1CH
Right
HTB 3 5.1CH
Custom
Right Surr.
Exit
Back Surr.
(RB/ LB)
Left Surr.
Subwoofer
Subwoofer
Front
Test Tone Manual
Test Tone Off
Center
Left
Surround
Center
Right
Back Surr.
Right Surr.
Back Surr.
BS/SW
(RB/ LB)
Amp
Left Surr.
Subwoofer
SW Re-mix
Exit
5
Select a speaker system.
1 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate subwoofer setting.
Subwoofer
On
C
L SW
LS
BS
R E
S P
1 "Subwoofer On":
When a subwoofer is connected.
2 "Subwoofer Off":
When no subwoofer is connected.
÷ The initial setting is "Subwoofer On".
÷ When "Subwoofer Off" is selected and the selection is estab-
lished by pressing the MULTI CONTROL # (or the Multi # key)
in step 2 below, the front speakers are set automatically to
"Front Large" and the procedure jumps to step 5.
2 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
3 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate front speakers setting.
1 "Front Large":
Large front speakers are connected to the receiver.
Speaker Distance Assignment
LEF Level
Game
Meters Digital
Input Function
Feet
Component
Exit
Video
Mode 1
Exit
Left Mode 2
Off
Center
Right
Right Surr.
Back Surr.
(RB/ LB)
Left Surr.
Subwoofer
Speaker Setup Custom
R
RS
C E I V E R S E T U P
E A K E R S E T U P
S U B W O O F E R
O N
Continued to next page
Exit
21
EN