Table of Contents
Advertisement
QQ
3 7 63 1515 0
PANEL VIEWS
REAR PANEL 2
ANTENNA
These jacks are for connecting the FM indoor antenna and AM loop
antenna that are supplied with the DTR-8.2.
AUDIO IN/OUT
These are the analog audio inputs and outputs. There are eight audio
inputs and 3 audio outputs. The audio inputs and outputs require
RCA-type connectors.
• When connecting a VCR or other video component, make sure
you connect the audio and video leads together (i.e., both to
VIDEO 3).
• The PHONO (PH) input jacks on the DTR-8.2 is designed for
use with turntables that use moving magnet cartridges.
RCA type
MONITOR OUT
The monitor output includes both composite video and S video
configurations. This output is for connecting television monitors or
projectors.
ZONE 2 AUDIO/VIDEO OUT
TE
L 13942296513
Connect the device that will be used in the remote zone (Zone 2).
COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component video
connectors, be sure to connect them to these component video
connectors on the DTR-8.2. The DTR-8.2 has two component video
input connectors to obtain the color information (Y, PB, PR) directly
from the recorded DVD signal or other video component and one
component video output connector to output it directly into the
matrix decoder of the display device. By sending the pure DVD
component video signal directly, the DVD signal forgoes the extra
processing that normally would degrade the image. The result is
vastly increased image quality, with incredibly lifelike colors and
crisp detail.
A-BUS
Congratulations for purchasing a most efficient, modern-day remote
controllable whole house audio system. A-BUS is a simple,
efficient, elegant audio distribution system. The wiring installation
time is significantly reduced as only a single CAT-5 wire is run to
each location. A-BUS is easy to use, reliable, affordable, and most of
all, far better sounding than conventional autoformer based volume
controls.
ZONE A/B/C/D:
Use a CAT-5 (eight conductor twisted) cable to
www
connect directly from the receiver ' s A-BUS RJ45 Hub to an A-BUS
keypad. A-BUS outputs enable connection up to four A-BUS
keypads.
.
http://www.xiaoyu163.com
x
ao
u163
y
i
http://www.xiaoyu163.com
2 9
8
Warning:
DO NOT connect A-BUS outputs to any computer or network
connections (i.e. ethernet). It will cause damage to the computer or
network components as 24-volt power runs on this same cable to
power the amplifier stages of the amplifier module.
IR control: Another feature of the A-BUS system is the ability to
control source equipment in another room where the A-BUS module
is installed. If you wish to control another source from the receiver at
the A-BUS keypad by remote control, connect A-BUS or another
brands' IR emitter on the receiver's 40 k terminal. Then place the
emitter on the remote receiver on the front panel.
Typically, the emitter will work when you connect with a 40 K
connector. If it does not work, try a 56 K connector.
DC INPUT: Connect A-BUS power supply. Do not use any other
AC Adapter on this connector as it may cause severe damage to the
receiver.
SPEAKERS
Seven terminals are provided for the front left, front right, front
center, surround left, surround right, surround back left, and
surround back right speakers. Speaker outputs are compatible with
banana plug connectors.
AC OUTLETS
The DTR-8.2 is supplied with AC mains outlets for connecting the
power cords from other devices so that their power is supplied
through the DTR-8.2. By doing this, you can use the Standby/On
Q Q
button on the DTR-8.2 to turn on and off the connected devices as
3
6 7
1 3
1 5
well.
Caution:
Make sure that the total capacity of the other components connected
to this unit does not exceed the capacity that is printed on the rear
panel (e.g., 120 watts).
AC INLET
Plug the supplied power cord into this AC INLET and then into the
power outlet on the wall.
•
Do not use a power cord other than the one supplied with the
DTR-8.2. The power cord supplied is designed for use with the
DTR-8.2 and should not be used with any other device.
•
Never have the power cord disconnected from the DTR-8.2
while the other end is plugged into the wall outlet. Doing so may
cause an electric shock. Always connect by plugging into the
wall outlet last and disconnect by unplugging from the wall
outlet first.
12V TRIGGER A/B/ZONE 2 terminal
These terminals are provided so that you can use the operation of the
DTR-8.2 control the operation of another externally connected
device. Connect the component to this 1/8-inch mini-jack terminal
and when the set input source is selected, the device will turn on. Set
the 12V TRIGGER terminal using the Setup menu: Input setup
12V trigger.
When the DTR-8.2 is in the ZONE 2 mode, this terminal outputs at
co
12 V/100 mA.
.
9 4
2 8
0 5
8
2 9
9 4
2 8
m
DTR-8.2
9 9
9 9
Advertisement
Table of Contents
