Install Volcanic Stone, Embers And Logs - Lennox Elite EDV35RNM Care And Operation Instructions Manual

INSTALL VOLCANIC STONE, GLOWING
EMBERS AND LOGS
NOTE: Turn off all electricity to the appliance
before you install volcanic stone, embers and
logs.
WARNING
• DO NOT attempt to install the logs
until the appliance installation
has been completed, the gas
line connected and tested for
leaks and the initial burner
operation has been checked out.
• The size and position of the log
set was engineered to give the
appliance a safe, reliable and
attractive flame pattern. Any
attempt to use a different log
set in the fireplace will void
the warranty and will result
in incomplete combustion,
sooting, and poor flame quality.
• Logs get very hot and will remain
hot up to one hour after gas
supply is turned off. Handle
only when logs are cool. Turn
off all electricity to the appliance
before you install grate, volcanic
stone, vermiculite, embers and
logs.
• This appliance is not designed
to burn wood. Any attempt to
do so could cause irreparable
damage to the appliance and
prove hazardous to your safety.
• If logs are not installed
according to the log installation
instructions, flame impingement
and improper combustion could
occur and result in soot and/or
excessive production of carbon
monoxide (CO), a colorless,
odorless, toxic gas.
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No.
88L53 FGE Bag of Glowing Embers
Bag of Decorative
80L42 FDVS
Volcanic Stone
12
Figure 6
Step 1. Remove the appliance front door (see
Removing Glass Encloslure panel on Page 11.
Step 2. Install decorative volcanic stone -
Sprinkle the decorative volcanic stone in a pleas-
ing pattern. The volcanic stone should be placed
directly on top of the firebox bottom, along the
front and to the back at the right and left sides of
the burner. Position any optional ceramic fiber
liners before placing the stone. Logs should be
positioned after the volcanic stone.
NOTE: This appliance is provided with enough
Glowing Embers for several applications, do
not feel compelled to use all that is in a new
bag. For best glowing effect, replace the ember
material annually. Replacement Glowing Em-
bers are available (Catalog Number 88L53).
Step 3.
(Rockwool) into pieces about the size of a
quarter (Figure 5). Keep the pieces fluffed up,
not matted. Distribute these pieces over the
front surface of the burner, as shown in Figure
6. Do not use more than is necessary. When
properly positioned, the Glowing Embers will
cover approximately 65% of the front burner
and with no appreciable gaps or openings.
Ensure that the main burner ports remain
uncovered by the ember material.
Description
Embers (rockwool)
Figure 5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Separate the Glowing Ember
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Glowing Embers
Step 4. Placement of Logs -
All top logs that rest on lower logs, do so over
notches, indents or nubs. Proper log placement
is critical to prevent sooting. Logs should be
placed in the gaps between the flame peaks and
should be positioned so they do not impinge
the flames.
Step 5. Position the individual logs as shown
in Figures 7 and 8. Logs should be placed in
the order shown. All logs that have notches
to fit over the grate tines should be positioned
with these notches directly against the grate.
Handle logs carefully to prevent breakage.
Proper log placement is critical to encourage
outstanding flame appearance and prevent
sooting. When positioned properly as shown,
logs will be positioned between flame peaks
and will not impinge any flames.
Refer to Figure 7 for EDV35 Series appliances
and to Figure 8 for EDV40 and EDV45 Series
appliances.