Audio Setup - Kenwood KDV-MP6433 Instruction Manual

The setting range of each feature is as follows:
Feature Setting range
BAS F 40/50/60/70/80/100/120/150 (Hz)
BAS Q 1.00/1.25/1.50/2.00
B EX OFF/ON
MID F 0.5/1.0/1.5/2.0 (kHz)
MID Q 1.0/2.0
TRE 10.0/12.5/15.0/17.5 (kHz)
4
Exit the detailed settings
ATT
VOL
AUD
SETUP
Q MENU STOP SCAN
• For each adjustment feature, see <Help? Term> (page 64).
• Setting audio control will set the System Q to "USER". For
System Q, refer to <System Q> (page 38).

Audio setup

Sets up volume offset, dual zone function, etc.
1
Start audio setup
ATT
VOL
AUD
SETUP
Q MENU STOP SCAN
2
Select features to set
ATT
VOL
AUD
SETUP
Q MENU STOP SCAN
Each time the knob is pressed, the type
changes in the following order.
Feature Setting range
HPF Specifies the front high-pass filter cutoff frequency.
HPR Specifies the rear high-pass filter cutoff frequency.
LPF Specifies the low-pass filter cutoff frequency.
PHAS Specifies the subwoofer phase.
V-OFF Adjusts the volume difference between sources.
LOUD Corrects treble and bass when the volume is low.
AVOUT Specifies the output level of the AV OUT terminal.
2ZON Turns the dual zone function ON/OFF.
AUTO
FM SCRL
AME
DISP
M/S SW
AM
RDM REP F.SEL M.RDM
SRC
AUTO
FM SCRL
AME
DISP
M/S SW
AM
RDM REP F.SEL M.RDM
SRC
AUTO
FM SCRL
AME
DISP
M/S AM SW
RDM REP F.SEL M.RDM
SRC
3
Set up each feature
ATT
VOL
AUD
SETUP
Q MENU STOP SCAN
The setting range of each feature is as follows:
Feature Setting range
HPF/HPR THRU (Filter Off)/40/60/80/100/120/150/
180/220 (Hz)
LPF 50/60/80/100/120 (Hz)/THRU (Filter Off)
PHAS REV (180˚)/NML (0˚)
V-OFF -8 – 0
LOUD OFF/ON
AVOUT -15 – 0
2ZON OFF/DVD/AUX
4
Exit audio setup
ATT
VOL
AUD
SETUP
MENU STOP SCAN
Q
• If a volume offset is set for each source with "V-OFF", the
volume will be nearly the same for all sources when the
source is changed.
• KDV-MP6433:
You can select "AUX" for "2ZON" only when CA-C1AX/CA-
C2AX (optional accessory) is connected.
• When "2ZON" is ON ("DVD"/"AUX"), you can only set "V-
OFF" and "LOUD".
• If the dual zone function is used, different sources can be
output from the front speakers (source of this unit) and
the rear speakers (disc source of this unit or the sound
input to the AUX).
• For "LPF" and "PHAS", the feature "SWPRE" needs to
be set to "SW" (subwoofer) in the menu setup, and
the subwoofer output to ON. For details on how to set
up "SWPRE", refer to <Menu setup> (page 44), and for
subwoofer output, refer to <Subwoofer output control>
(page 38).
• "PHAS" cannot be set up when "LPF" is set to "THRU".
• "AVOUT" can be set when the feature "SWPRE" in <Menu
setup> (page 44) is set to "AV".
#
: Press for # seconds.
AUTO
FM SCRL
AME
DISP
M/S SW
AM
RDM REP F.SEL M.RDM
SRC
AUTO
FM SCRL
AME
DISP
M/S AM SW
RDM REP
F.SEL M.RDM
SRC
English 37